Reviews
Use as a cargo hook Size is also unobtrusive and fashionable dress-up!
Quantity attached to the Main pipeCover of CROSS CUB110 (JA60):Pair (for Left and Right) Remove the screws at three locations each,
I changed to License bolt to use it for Carco Hook.
The size is just right for hooking Cargo Net or Elastic band.
I am concerned that the Center cover may be damaged, but I would like to find something to protect it.
Main pipeCover Screws are available in M5 and M6.
M5 screws have a gap of about 10mm, while M6 screws have a gap of about 5mm,
NylonSpacer and NylonBush are available.
This will hold it firmly in place without any rattling.
View detail
Parenthesis good!
Parenthesis is good. I replaced Mirror of Takekawa, but it is hard to see as I expected. [Color] It is not clear, so it may be difficult to distinguish fat cars and White Motorcycles… You have to be careful about tracking.
The Mirror and Bracket are operated by the ball, but it has a screw so that it can be re-tightened if it gets loose.
View detail
Use with Bush Face's License Plate Holder.
I combined it with PolishFace's License Plate Holder. I use Cemedine's METAL Lock to fix the Holder and Bracket tightly. It has a good feeling of rigidity. View detail
To Restore.
I used it on a MAJESTY 125 Restore that I purchased used.
The oil leak from the cylinder head, which is a pre-existing condition of this vehicle, was so severe that we decided to replace it because it was in a very scary condition to drive.
The work went smoothly and the leak was stopped without incident.
I have no problems with the quality and I would repeat it again because it is inexpensive.
View detail
Looks GOOD!
I purchased it at the same time as the Front Blinker part.
To install, simply attach it to the Body with Double-sided Tape and affix it to the vehicle body.
Front Blinker is the same, but the Fit is not quite right; Wobble is not, but there is a gap.
It looks GOOD, but the Fit feeling was not so good.
View detail
It looks good
[How is it used?
Town ride
Was the one you received as per Image?
It is not too dark at night on Image Street.
It looks better.
Was the installation difficult?
We used double-sided tape to affix it, but since there were no instructions on where to affix it, we affixed it where it would adhere best.
Additional double-sided tape was also applied.
[Included Parts:were they on?
Double-sided tape only, no Instruction Manualetc.
[Was there anything that disappointed you?
It's not so much that I need an instruction manual, but at least explain where to put the double-sided tape.
Also, the fitting is not good. It does not fit snugly and seems to float a little.
I guess I can't help it since I'm so focused on appearance.
View detail
For a little Accent
[How is it used?
The bolts that hold up the exterior of my long-owned motorcycle have become rusted over the years, If we're going to replace the Bolt anyway, let's put some Accent in it." This product was purchased to match the Cap bolt with the
The several color variations are useful because they allow Spacer to be used in accordance with the color of the car body.
Was the one you received as per Image?
Standard for this type of aluminum spacer. FUJI TUBO type. The product was just as beautiful as the image on Webike's website, and it was exactly as shown in the image, without the uneven staining that is common in low-priced aluminum collars from other companies.
Was the installation difficult?
There is nothing difficult about this product, as it is installed by biting it in place of a washer when using a cap bolt.
How was your experience with it?
Since it is made of aluminum material, each piece is light in weight and can also serve as a washer, making it a very convenient product that can be used in a wide range of applications.
The BoltSingle Body can be used as a one-point accent when installing the License Plate, which is not so easy with the BoltSingle Body.
It is not lightweight, reinforced, etc. (strictly speaking, there is a slight increase in color), and it costs a lot of money, but I like this kind of product, and I am very grateful for it.
The appearance is that of the FUJI TSUBO Type Design from a generation ago, so in the age of 2025 Fashion!" I'm not a middle-aged person, but I'm not a trendy middle-aged person.
[Included Parts:were they on?
None
2 piecesQuantity:The price for the set is 880 yen, and I would appreciate it even more if it were a little cheaper, but the product is out of season, so I guess I should be glad that it is on the market.
[Was there anything that disappointed you?
If you like the design as shown in Webike's image, you can buy it. Disappointing. It is lightweight enough.
Make good use of the wide selection of 9 colors to add flair to the Accent of your car body.
Other items that would be helpful
Point and hang of installation
As mentioned above, it is like a fashion color used in place of a bolt washer, so it is a simple job to use the Barnacle Collar when attaching a cap bolt of the appropriate length to the bolt stop on the attachable part.
[Availability and clarity of the Instruction Manual
No Instruction Manual is available
The ease of understanding is at the top level, so I don't think that wrong usage is likely to occur (unless you get twisted and use it in a different way on purpose).
[Notes]
None in particular, in Color variations. The color tones are different from what I saw in the picture." There may be some things that are not so common in motorcycle accessory stores anymore, but that may not be a problem.
[ITEMS TO BUY TOGETHER
Cap boltTypeExclusive Since it is like a collar, please purchase a cap bolt of each material & length that you want to install.
[Opinions and requests to Manufacturer
It is easy to purchase large quantities if the price is a little lower, so a quantity of 10 pieces is 10% cheaper.:A Set would be even more appreciated, please.
View detail
Fits: YAMAHA Super Jog ZR, YAMAHA BJ, YAMAHA BWS(BWS), YAMAHA APRIO, YAMAHA JOG APRIO Type 2, YAMAHA SUPER JOGZ, YAMAHA Remote controller jog, YAMAHA VINO(2Cycle), YAMAHA Remote controller jog, YAMAHA VINO(2Cycle)
I guess it's worth the price
It wasn't what I expected, but it wasn't bad either. View detail
Fits: HONDA DIO, HONDA SUPER DIO, HONDA DIO FIT, HONDA LIVE DIO, HONDA SMART DIO, HONDA CREA SCOOPY, HONDA ZOOMER
Nice quality front fork
This machined aluminum front fork works fantastic on a Honda NPS50. They are of good quality and look nice. Do better than the original front fork. -------------------------------------------------- -------- This edited aluminum fork is fantastic on a Honda NPS50. Are of good quality and look nice. Do better than the original fork. Powered by Google Translator View detail
Fits: YAMAHA VINO(2Cycle), YAMAHA SUPER JOGZ, YAMAHA SUPER JOGZ, YAMAHA SUPER JOG ZR, YAMAHA JOG POCHE, YAMAHA JOG APRIO Type 2, YAMAHA JOG (2Cycle), YAMAHA APRIO, YAMAHA APRIO
scratch
Carbon paint peeling
without Logo
Are you inspecting?
View detail
Fits: YAMAHA NMAX155, YAMAHA NMAX, YAMAHA NMAX155, YAMAHA NMAX
The feeling of shifting gears has changed quite a bit.
The Belt was replaced because it had traveled 18,000 km since the last Belt replacement. When we looked at the removed Belt, we found that it had not worn down to the limit of use, but the side angles were worn and attached.
I was worried about how the shifting would feel after installation, but I got the impression that the shifting became smoother, which was a good impression. However, I had the impression that the Engine RPMs dropped a little when shifting throughout the entire range, and the maximum speed dropped. (Tears)
I need to re-set with Weight Roller.
View detail
Prepare just in case
We prepared just in case this was the first time we had to replace a Tire. View detail
Fits: YAMAHA JOG (2Cycle), YAMAHA Remote controller jog, YAMAHA JOG, YAMAHA JOGDELUXE, YAMAHA Axis Treat, YAMAHA Remote controller jog, YAMAHA Remote controller jog, YAMAHA Remote controller jog, YAMAHA Remote controller jog, YAMAHA JOG (2Cycle), YAMAHA JOG, YAMAHA JOGDELUXE, YAMAHA JOG (2Cycle), YAMAHA JOG (2Cycle), YAMAHA JOG (2Cycle)
It's like OEM, and the price is very low.
The last 2-stroke JOG instead of a foot Remote controller jog I purchased this product because one of the blinker lenses was broken at that time. I purchased this product because one of the blinker lenses was cracked at that time.
OEM parts are also available, but the price is more than three times different, so we have to settle for cheap products.
No modification is required for installation, and the venue is about 98% the same as NORMAL. If you look strictly at the BALI, there are some things such as the presence or absence of BALI, but there are no obstacles.
The color difference from the OEM was the same as the OEM for a quick look. The one that needed to be replaced was the one side, but this product is Quantity:Pair (for Left and Right) Therefore, the Quantity:Pair (for Left and Right) We also exchanged with
I can spare the NORMAL for the one that is available!
I want to make sure I don't fall and Repeat.
View detail
![Reinforced Center Spring Middle Type [Medium]](https://img.webike-cdn.net/catalogue/images/31791/12151649_566fc6017084c_TS.jpg)
Fits: SUZUKI address V125, SUZUKI address V125, SUZUKI address V125, SUZUKI Address V125S, SUZUKI address V125, SUZUKI address V125, SUZUKI address V125
Excellent spring for increased torque
Fits: SUZUKI Address V100, SUZUKI Address V100
OEM's with Stages for acceleration modification.
As a precaution for installation, …Crank is an Opposite Thread Screw and the length of the Spline is limited, so there is a possibility of crushing it if it is tightened too much.
Grease is applied to the WR, but it is too little, so I applied additional grease. The Plus screw on the back cover is hard, but it loosens easily with the Impact Driver.
The PRESS processing on the back cover is rough in some areas and requires a compromise by the user.
The performance is more than sufficient, and although it may not be as good as the High Speed Pulley, it accelerates linearly with the Axel without any staggered acceleration.
To take advantage of the High Speed Pulley, it is necessary to consider the driven side as well, so if you are assuming that you are going to install it by itself, I think you will not be dissatisfied with this Pulley kit.
The weight of the attached wr is also a good feeling. I think it could be a little lighter for a young girl.
View detail
stage 6 mirrors
item received as described and well packed. received on time as well. will order more in the future stage6 mirrors are one of the most soughts mirror for small CC scooters such as namx xmax aerox... View detail
Cheap and affordable_OEM alternative
Something cheaper than OEM." I was looking for a Motorcycle supply store with the motto of
Although there are variants for Custom Ordinary." is not surprising.
I'm glad I found it on webike!
This is a great price for the front and rear parts and Screws included.
View detail
Custom
Recommended for those who do not want to put CALSeal directly on the License Plate! View detail
Fits: YAMAHA SMAX, YAMAHA SMAX, YAMAHA FORCE 155, YAMAHA Majesty S, YAMAHA Majesty S, YAMAHA BW'S R, YAMAHA BW'S 125, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X
All the OEM Parts you need are included.
It is better than ordering by parts Single Item, because it contains the parts you need. View detail
Fits: YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA CYGNUS X, YAMAHA CYGNUS X
CYGNUS-X Taiwan 5th stage is finally fully LED♪
[How is it used?
Touring and mainly city driving, with some night driving.
We had changed OEMTail to Smoked lens, and now the Rear blinker has become LED Blinker with this product.
The front blinkers were previously LEDs, so they were upgraded to front and rear LEDs.
Was the one you received as per Image?
Quantity:Pair (for Left and Right) The two blinkers are also wiring processed, so there is no need to replace the blinker relay when converting LEDs!
Double-sided tape is also included for easy installation.
Was the installation difficult?
In Taiwan 5th period, Tail is LED and Blinker is ValveLamp.
Valve is a member of the [Color] Clear, with OrangeCover attached with Screw, removed and installed.
A single screw in the middle and double-sided tape on the SIDE hold it firmly in place, so it will not rattle due to vibration.
How was your experience with it?
A sharp, LED-specific glow.
The sense of luxury has been improved.
The number of balls also looks good for rearward visibility.
The lens is used with a smoked lens and is clearly visible even in bright light.
I feel that the blinking lights are more vivid, and I feel that safety is improved when using the Blinker or Hazard lamps.
[Included Parts:were they on?
Two screws are provided for fixing.
There is no Instruction Manual, but just remove and install. It is easy to install.
View detail