Reviews
Fits: YAMAHA BWS100(BWS), YAMAHA GRAND AXIS, YAMAHA AEROX100
Oh no!
Overheat immediately after replacement and Engine stops and seizes? It was immediately returned to OEM and runs fine. View detail
Fits: HONDA gyro canopy, HONDA LEAD 50, HONDA LEAD 50, HONDA TODAY, HONDA DIO(4Cycle), HONDA DIO (2Cycle), HONDA DIO (2Cycle), HONDA TACT, HONDA TACT, HONDA TACT, HONDA ZOOMER, HONDA SMART DIO, HONDA SMART DIO, HONDA SMART DIO, HONDA SUPER DIO, HONDA SUPER DIO, HONDA SUPER DIO, HONDA SUPER DIO, HONDA SUPER DIO, HONDA SUPER DIO
Too inaccurate to use!
It is so inaccurate that I can't use it at all because I can't fit it into a Large, and I can't move the Plate! I replaced it with an OEM one and it worked Smoothly. View detail
Fits: YAMAHA vino, YAMAHA vino, YAMAHA vino, YAMAHA vino, YAMAHA JOG, YAMAHA JOG Zr, YAMAHA VINOMolar feh, YAMAHA VINOMolar feh, YAMAHA VINOMolar feh
Failed after only 4000 km.
Purchased as a replacement for VINO (SA26J).
（The V Belt (which had been replaced at the same time as this assembly) was shattered after only 4000 km.
After replacing the V Belt at a Motorcycle shop, the car was shattered again, after only a dozen or so kilometers.
(The motorcycle shop had just changed the belt, but this time they didn't cut corners.) The clutch was also inspected.
Then, an anomaly was found in two Pulleys in ASSYRear.
V Not the surface that Belt hits.
The convex part of the Rear Pulley (SecondarySieveComplete) and the tubular part of the Front Pulley (SecondarySlideIngSieveComplete) that it is penetrating are wobbly and rickety when touched by hand.
This caused uneven rotation and the wavy V Belt seemed to break into pieces.
But to begin with, the two pulleys do not rotate separately, so the part is not even worn.
Cause unknown.
Was either Pulley a manufacturing defect with a shaky core?
Since it is an assembly, we did not disassemble it after purchase and installed it on the Motorcycle as is.
Other parts, the surfaces interfering with the shaft, are not worn.
Clutch plates are not so worn.
View detail
Fits: HONDA TODAY, HONDA TODAY, HONDA DIO 4 Str., HONDA DIO4st CESTA
6 months of use
Self-replacement, riding for 6 months, there was a speed increase of about 10km, but at some point, the initial torque did not rise and the vehicle did not move. I do not know, but I returned the parts to the original condition --------------------------------------- ------------------- Self -replacement, riding for six months, and a 10km speed up, but from one point, the early torque did not rise and the vehicle did not go. The vehicle was checked. I'm not sure, but I put it back with a pure part. Powered by Google Translator View detail
Fits: YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA jog sports, YAMAHA Apprio
I do not recommend it.
The inner diameter of the pulley boss seems to be slightly smaller than the OEM product, so it could not fit in the shaft and could not be installed. View detail
Fits: HONDA TODAY, HONDA TODAY, HONDA DIO 4 Str., HONDA DIO4st CESTA
Product is fine.
The product could be used without any defects.
Product Page delivery date is scheduled to ship tomorrow. (In stock at Partner warehouse) However, when I actually placed the order, I found that the expected shipping date was a week later, and I was troubled. If I had to wait a week, I would have bought it from Amazon or Rakuten, even if it costs a little more. Please display a more accurate delivery date!
View detail
Fits: YAMAHA vino, YAMAHA vino, YAMAHA vino, YAMAHA vino, YAMAHA JOG, YAMAHA JOG Zr, YAMAHA VINOMolar feh, YAMAHA VINOMolar feh, YAMAHA VINOMolar feh
Not worth repairing.
A few days after popping it on, a noise occurs?
Rose the Clutch, Clearanceetc.Check….
I could understand the messiness of the Made in Taiwan product. The mounting plate of the three clutches is distorted. Because of the distortion, one of the clutches is not open. The thickness of the sieve is also RoseRose….
It's not Repair.
View detail
It was defective
It is not durable and it went bad in a month.Cost performance is great. Cost performance is great, but the part where you put the collar is deformed and the gold collar on the inside is cracked. View detail
Fits: SUZUKI ADDRESSV125S CF4MA L0, SUZUKI ADDRESSV125S CF4EA L0, SUZUKI ADDRESSV125LIMITED CF4EAK9, SUZUKI ADDRESSV125LIMITED CF46AK9, SUZUKI ADDRESSV125G CF4EAK9, SUZUKI ADDRESSV125G CF46AK9, SUZUKI ADDRESSV125 CF4EAK9, SUZUKI ADDRESSV125 CF46AK9, SUZUKI ADDRESSV125LIMITED CF46A K9, SUZUKI ADDRESSV125LIMITED CF46A K7, SUZUKI ADDRESSV125G CF46A K9, SUZUKI ADDRESSV125G CF46A K7, SUZUKI ADDRESSV125 CF46A K9, SUZUKI ADDRESSV125 CF46A K7, SUZUKI ADDRESSV125G CF46A K6, SUZUKI ADDRESSV125G CF46A K5, SUZUKI ADDRESSV125 CF46A K6, SUZUKI ADDRESSV125 CF46A K5
Pulley back cover chipped and cracked
Standard TypePulley
There are deformations and cracks in the hollow part where the Pulley back cover Slide Piece fits.
I have asked for a return policy, but the communication is slow.
View detail
![Address V125 Clutch Shoe Assy [K9/L0].](https://img.webike-cdn.net/catalogue/14190/12251340_567cc8c14d228_TS.jpg)
Fits: SUZUKI Address V125S, SUZUKI address V125
Clutch Shoe thickness use limit 2.0mm or less
Clutch Shoe thickness, use limit 2.0mm or less, average 2.0mm, Clutch Shoe thickness is not uniform, too many chips and tensions, unusable, can not function uniformly, return and exchange. In case you are interested in a new Clutch Shoe, the thickness is 3.0mm. View detail
![Drivetrain Adjustment Washer [0.5mm] JOG Series [Thin Axis]](https://img.webike-cdn.net/catalogue/14190/12121253_4d044728cdbaf_TS.jpg)
Fits: YAMAHA Cygnus X, YAMAHA Jog (2 cycle), YAMAHA Jog (2 cycle), YAMAHA BWS100 (Bewith), YAMAHA BWS125 (Bewith), YAMAHA Axis 90, YAMAHA Axis Street, YAMAHA Jog 90, YAMAHA BWS100 (Bewith), YAMAHA BWS125 (Bewith), YAMAHA Axis 90, YAMAHA Axis Street, YAMAHA Jog 90
Don't buy this if you are a CYGNUS X rider!
fine shaft (JOG) Even though it is written "CYGNUS X1", there is CYGNUS X1~4 type in the details of the suitable car model.
It does not fit at all because it is a fine for Shaft.
This could be close to a scam…
View detail
![High Speed Pulley Kit [KAISOKU]](https://img.webike-cdn.net/catalogue/images/31791/10170124_507d8a4ad8b26_TS.jpg)
Fits: YAMAHA Cygnus X Type 1, YAMAHA Cygnus X Type 1, YAMAHA Cygnus X Type 2, YAMAHA Cygnus X Type 2, YAMAHA Cygnus X Type 3, YAMAHA Cygnus X Type 3, YAMAHA Cygnus X Model 4, YAMAHA Cygnus X Model 4, YAMAHA Cygnus X Model 5, YAMAHA Cygnus X Model 5, YAMAHA BWS 125 Type 2, YAMAHA BWS R, YAMAHA BWS X 1 type, YAMAHA BWS125 Type 1, YAMAHA MAJESTY125, YAMAHA BWS125 Type 1, YAMAHA Axis Treat, YAMAHA CYGNUS X Type 1, YAMAHA CYGNUS X Type 2, YAMAHA CYGNUS X Type 2
I'm not happy.
CYGNUS X.
It was hard to get it in. I couldn't get into it very well.
And when I test drove it, it was slower than NORMAL. It's slower than NORMAL. No maximum speed.
Wound was attached to the product from the beginning.
Another external Pulley was a completely different story and faster.
View detail
It's the worst
I purchased this product after checking the product information many times and it is defective. I'm not sure if I can get the belt to hit the case or not. I would like to return it or replace it with a normal Drive pulley. View detail
Parts were defective and could not be installed.
I couldn't get to the Ramp Plate because of the misalignment of the center of the spline hole.
It was obviously adulterated with a manufacturing defect that was distributed to the customer.
I'll contact the company you purchased it from immediately and attach a photo of the situation.
I applied for a replacement for the defective product, but I only received an email from the system's receptionist and no contact from the person in charge.
After 5 days, I finally got a call from the rep, only asking me to send them the car's name, model and VIN.
This product is sold clearly stating that it is compatible with all models.
Why do we need the type of
If you are forced to send the requested information
And then two days later, he asked me to send him a picture that shows the problem.
The answer came back to me. I was so appalled that I couldn't say anything.
It's disgusting.
I've filed a bad application with a proper photo first.
Are you looking at nothing and responding to Objection?
What have you been doing all this time to send me pictures now?
A totally insincere answer.
I'm sending you the pictures first, so you can see them.
When we contacted them, we made a mistake and they hadn't seen the photos.
I'll send it to the manufacturer now and see what they can do.
He said he was sorry.
At this point, it has been ten days.
Finally, 12 days after filing the Objection yesterday, we finally got the
I'm trying to get to the Gold level.
And the comments at the time.
It looks like the Hole Center is out of alignment in the photo.
It's just that the parts are shifted around in the picture.
It's possible that this is not a defective part due to a hole center shift
But just in case you're wondering, I'll return the gold.
Well, what a bad product you're distributing and you don't want to admit it.
Even more supercilious comments without sincerity!
I'm causing a lot of trouble for my customers!
I strongly vowed to never buy things from here again!
View detail
Fits: HONDA dunk, HONDA dunk, HONDA Giorno, HONDA JOG DELUXE, HONDA JOG, HONDA Giorno, HONDA Giorno DELUXE, HONDA TACT, HONDA TACT
Not available
I haven't even put 5,000km on it, but the Slide Piece shattered it
The Ramp Plate scraped and damaged the Pulley
If you're an OEM, I've never heard of it being damaged in such a short distance
I can not use it at all
View detail
Fits: SYM RV150, SYM RV125, SUZUKI ADDRESSV125, KYMCO GRAND DINK125, KYMCO GRAND DINK150, HONDA LEAD125, HONDA SPACY125, HONDA PCX125, HONDA PCX150
I bought it because it was cheap, but..
It has 16,000 miles on it and is as pictured
Strange noises from the drivetrain, hitting head on at 80km/h, and poor fuel economy, Crank Case tries to find out why When I opened the Cover, the surface was stripped and the Gold genus of Body was considerably shaved Naturally, PulleyWeightGrease is applied at the time of exchange
The OEM has almost 21,000 miles intact, and honestly, I've never seen the Weight roller do this before I did
We replaced it with a DAYTONA, and it's back to normal with no noise and speeds over 80km/h I did
I will never buy again
View detail
It is different from ordering
Despite ordering Weight Roller for 16 grams [The end number 160 of the model number indicates 16 g] The items we received are 11. Marking 5g and Roller. As it turns out, I will make a return request after all, but only the instruction to the request form is postage prepayment. I can not accept it. You might as well be careful when purchasing.
View detail
Screw will not come off
Of three screens Quantity : 2pc can be off normally, no matter what you do 1 Gap does not happen. Even if you hit with the Penetrating Driver, even if you use Slotted screwdriver, you can not slip even if you apply the anti-slip liquid to the screw head or apply the cooling Spray and push the Impact Driver and rotate it. It does not make sense if performance is good or not usable. For Manufacturer, I think that you can do the least product management before returning it to Package. (The inquiry staff's argument is "The damage of Screw Mountain is caused by customer's work. ~ In this case, the fact that it is being tightened with high Torque, checked the state indicated, and as a result of the customer's work at the judgment of the customer himself, as a result of licking Screw Mountain, various tools It means that the result was damaged as a result of being unable to go out even by using it. It is said that. I'm fooling around. View detail
Fits: YAMAHA Jog 90, YAMAHA Grand Axis, YAMAHA Apprio, YAMAHA BWS100 (Bewith), YAMAHA Super Jog ZR, YAMAHA Axis 90, YAMAHA Jog 90, YAMAHA Grand Axis, YAMAHA Apprio, YAMAHA BWS100 (Bewith), YAMAHA Super Jog ZR, YAMAHA Axis 90
can not use...
Torque Camshaft will not fully open as you build this Slider... In the SUPER JOG Zr 3 YK, when Torque Camshaft is fully opened, the Spring is also completely contracted, so Torque Camshaft can not move by the thickness of the Slider.
When asking KN project...
"If you change to Spring with few windings... "
In short, it seems to be incompatible with Springs with the same number of turns and wire diameter as Normal spring.
View detail
I have a KN variator which I like, so I decided to try the KN belt. I think the photo says it all. I have used several brands of belts, and this is the only one which has done this. It was still almost new. VERY dissatisfied, complete waste of money!
I have a KN variator which I like, so I decided to try the KN belt. I think the photo says it all. I have used several brands of belts, and this is the only one which has done this. It was still almost new. VERY dissatisfied, complete waste of money! View detail