Reviews
Fits: SUZUKI Address V100, SUZUKI address V125
Probably 2000rpm UP Spring
For ADDRESSV125. Probably 2000rpmClutch meatTimingUP RedSpring.
If you weigh 85kg, at least WR weight is lighter than 16g, and under the condition that an external exhaust system is installed, it will be faster from low speed to high speed. However, the clutch will wear faster than the NORMAL because it meets at higher rpm.
View detail
Fits: HONDA ADV150, HONDA PCX125, HONDA PCX150, HONDA Click125, HONDA Spacy125, HONDA LEAD125, KYMCO GRAND DINK125, KYMCO GRAND DINK150, SUZUKI ADDRESSV125, SUZUKI Avenisu, SUZUKI swish, SYM RV125, SYM RV150
0.WR in 5g increments
KN Project Dasan Only Round TypeWeight roller (WR) Weight is set in 0.5g increments (And then there's the oddly shaped Dr. Pulley) 。
The same is true for all WRs, but since there is BALI, just remove the BALI with sandpaper, etc. and the rotation will be smooth.
WR weight matching is possible down to 0.1g, and the same number of grams is placed diagonally for smoother rotation loss. (without eccentricity) The WR of KN project had an error of ±0.1g, which is a normal accuracy.
Durability is normal.
The price is half that of a well-known manufacturer.
No Grease required for WR (It will be a resistance, and it will also lure in Beltkus, which will also be a resistance). Axel full open highest speed to full closed/full Brake to full open (Re-acceleration) When the stickiness is a little bit by Grease etc. at the time of (resistance) Response is delayed if there is a
View detail
Fits: YAMAHA Super Jog ZR, YAMAHA BJ, YAMAHA BWS(BWS), YAMAHA APRIO, YAMAHA JOG APRIO Type 2, YAMAHA SUPER JOGZ, YAMAHA Remote controller jog, YAMAHA VINO(2Cycle), YAMAHA Remote controller jog, YAMAHA VINO(2Cycle)
I guess it's worth the price
It wasn't what I expected, but it wasn't bad either. View detail
Fits: HONDA MONKEY, HONDA SUPER CUB 50, HONDA LITTLE CUB, HONDA NSR50, HONDA NSR80, HONDA NS-1, HONDA NS50F, HONDA MBX50, HONDA CRM50, HONDA CRM80, HONDA MONKEY, HONDA GORILLA, HONDA Monkey Baja, HONDA MONKEY R, HONDA MONKEY RT, HONDA DAX50, HONDA DAX70, HONDA JAZZ, HONDA MAGNA50, HONDA CHALY 50
CUB press 50 AA01 Fi No fit ….
The Bolt was in a different position than the one originally attached.
Since the suppression plate is not included, it cannot be installed if the screw position does not match that of the installed Sprocket.
I'm still not sure if it's a product defect or a non-conformity.
View detail
Fits: KYMCO LOOKER 50, KYMCO SOONER 50, KYMCO SUPER9 50, KYMCO LOOKER 50, KYMCO SOONER 50, KYMCO SUPER9 50
KN Planning Reinforced Slide Piece
I replaced it with a drive belt because there was sometimes a strange noise coming from the drive train while waiting at a traffic light or idling. The old Slide Piece had a large rattle, and the new one had almost none. The noise has been eliminated and I can ride comfortably. View detail
Fits: YAMAHA SUPER JOG ZR, YAMAHA Remote controller jog, YAMAHA Remote controller jog, YAMAHA VINO(2Cycle), YAMAHA VINO(2Cycle), YAMAHA SUPER JOGZ, YAMAHA JOG APRIO Type 2, YAMAHA APRIO, YAMAHA BWS(BWS), YAMAHA BJ
OEM Replacement
Used on SA10J 2-stroke VINO.
The OEM clutch had about 28,000 km on it, and when starting the car, the clutch would connect with a loud "shock".
ClutchJudder or Clutch Slip?
The Clutch Shoe was still there, so I scrubbed the Clutch Shoe and Clutch outer with sandpaper to cover it up, but the Shock remained a little.
I replaced only the Clutch Shoe with this one because it is cheaper than the OEM.
Shock at startup has also been eliminated and the car can now start off Smoothly.
The quality of the product is reasonable, but not as good as OEM products. I don't know about the durability as I will be using it more and more.
The rating is 3 stars because it is a replacement for an OEM replacement consumable, so it was not particularly easy or impossible to use.
If OEM is too expensive and you are having trouble replacing it, you can try this one.
View detail
Fits: SYM RV150, SUZUKI ADDRESSV125, SYM RV125, KYMCO GRAND DINK150, KYMCO GRAND DINK125, HONDA LEAD125, HONDA SPACY125, HONDA PCX150, HONDA PCX125
Replaced at 20,000 km
[How is it used?
Replaced after 20,000 km.
Acceleration and deceleration were normal.
How was your experience with it?
No different than OEMs
How did it compare to other products?
OEMLevel
[Points to note]
Note the direction
View detail
Fits: HONDA DJ-1, HONDA DJ-1, HONDA Gyro UP, HONDA gyro X, HONDA gyro canopy, HONDA Julio., HONDA Johno., HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA Superdio, HONDA baton, HONDA baton, HONDA diocesan, HONDA TODAY., HONDA TODAY., HONDA Livdio ZX, HONDA livudio, HONDA baton, HONDA baton
Functions but no hole to Wrench.
The title is true
When integrating the Clutch into the Driven, it cannot be secured because there are no holes.
If you have various tools, you can handle it, but if you don't have them, you may lack Torque tightening if you tighten it properly.
Dio that was only 35 kilos. (Mileage just under 30,000) is now close to 60, so I think its performance as Clutch is not bad.
View detail
Fits: YAMAHA vino, YAMAHA vino, YAMAHA vino, YAMAHA vino, YAMAHA JOG, YAMAHA JOG Zr, YAMAHA VINOMolar feh, YAMAHA VINOMolar feh, YAMAHA VINOMolar feh
Good product, but 2 weeks from order to arrival
The NORMAL Clutch has two pieces, but this item has three.
Be careful when you want to replace only the Clutch or Spring at a later date by reducing the ASSY.
Center spring is stronger.
So far, no problems.
However, I had to wait two weeks for delivery.
This is despite the fact that when I placed the order, the order page indicated that it would ship in 3 days.
Partner Warehouse. Into In stock." I'm just saying.
It is too late to be informed by email after the order has been accepted.
If I had been in a hurry, I would have definitely purchased elsewhere.
Even if they were waiting to be assembled, there is no way they would be so slow in communicating with FOR JAPAN MODEL.
The delay was probably due to waiting for deliveries from China, Taiwan, and other foreign countries.
View detail
Fits: HONDA GYRO system (TA01), HONDA GYRO system (TA02), HONDA GYRO series (TD01), HONDA jorio, HONDA Giorno, HONDA GIORNO CREA, HONDA ZOOMER, HONDA TACT, HONDA TACT, HONDA TACT, HONDA DIO General, HONDA TODAY, HONDA Byte, HONDA LEAD 50, HONDA LEAD 50, SYM DD 50
KN Planning Weight Roller6g
I have only installed it for a short time, but I felt that the start was not as good as the NORMAL.
Response is better compared to NORMAL while driving.
I gave it 3 stars because I don't know how durable the rest will be.
View detail
Fits: YAMAHA MAJESTY125, YAMAHA CYGNUSZ, YAMAHA BW'S R, YAMAHA BW'S125, YAMAHA BW'S X, YAMAHA BW'S125, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X
I'll wait for someone to post the results to see if there are any bad effects.
I'm holding off on replacing it because I think it might have the same effect as lengthening the belt because the OD is smaller and reaches deeper into the Torque Camshaft groove, but it would increase the rattling in the groove, so I thought I could wait until I see what someone else has done before replacing it. View detail
Fits: YAMAHA Tricity155, YAMAHA tricity, YAMAHA Tricity155, YAMAHA tricity
It was cheaper than OEM Product.
I purchased this product as a Belt replacement for my Initial ModelBirdCity125.
The reason for our decision was that it was cheaper than OEM Product and we had used the same Manufacturer's product to replace the belt on a 50cc Scooter we had previously ridden.
The vehicle was bought used, so the BeltTrip was the same as the Odo, but the OEMBelt that came with it was not particularly thin or cracked…….
I hope this Belt will last as long.
The Roller was also replaced at the same time, and after the replacement, the start was smoother.
View detail
Fits: SUZUKI Let's 2 (2-stroke), SUZUKI Let's 2 (2-stroke), SUZUKI Let's 2 (2-stroke), SUZUKI Let's 2 (2-stroke), SUZUKI Let's 2 (2-stroke), SUZUKI Verde., SUZUKI Verde.
Rating for Pulley Set
The durability of the plastic product of the Guide part is not good. It is necessary to apply some kind of coating agent like paint type. In addition, the grease etc. scatter and disappear immediately.
Belt strength is not considered to be a problem.
View detail
Fits: YAMAHA BWS 125 type 2 domestic specification BG1, YAMAHA BWS R type 2, Taiwan specification 2JS, YAMAHA BWS X 1 type Taiwanese specification 46P, YAMAHA BWS125 Type 1, Taiwan specification 5S9, YAMAHA Cygnus X model 1 domestic specification 5UA, YAMAHA Cygnus X Model 1 Taiwan Spec 5TY, YAMAHA Cygnus X Model 2, Domestic spec 28S, YAMAHA Cygnus X Type 2 Taiwan Spec 1CJ, YAMAHA Cygnus X Type 2 Taiwan Spec 4C6, YAMAHA Cygnus X Model 3 Domestic 1YP, YAMAHA Cygnus X Type 3 Taiwan Spec 1MS, YAMAHA Cygnus X model 4 domestic spec BF9, YAMAHA Cygnus X Model 4 Taiwan Spec 2UB, YAMAHA Cygnus X Model 5 Domestic spec B8S, YAMAHA Cygnus X Model 5 Taiwan Spec B2J
Repeat purchase.
It seems to have become thin somehow. Because of that, Grease is flying outward by centrifugal force.
This wasn't the case when I bought it before (19.8).
View detail
Fits: YAMAHA BWS125(BWS), YAMAHA BWS125(BWS), YAMAHA SMAX, YAMAHA Axis Treat, YAMAHA CYGNUS X, YAMAHA MAJESTY125, YAMAHA MAJESTYS
For Setting
I bought it to explore Setting of CYGNUS.
The price is low and it doesn't hurt to make a mistake.
View detail
Fits: YAMAHA BWS125 (Bewith), YAMAHA BWS125 (Bewith), YAMAHA BWS125 (Bewith), YAMAHA BWS125 (Bewith), YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X
Easy to replace!
[How is it used?
I used it for my commuter vehicle CYGNUS X SE44J Japanese specification type 3.
While driving, I suddenly heard a crack and a rattle.
If you look closely, you will see that the Red outside cooling fan that came with the unit when you bought it has been shattered.
I chose this product which was in stock at short notice.
Was the one you received as per Image?
It was just like the image, but the lightness was slight, and the wings were so small that I was a little worried about whether the air was being delayed in the Head firmly.
Was the installation difficult?
It is easy. But don't be bothered, remove the Helmet in and prepare the L-shaped +Driver.
How was your experience with it?
To be honest, it's the same as before, and the Engine is NORMAL.
I think the Yellow color stands out and I don't like it a little, lol.
[Included Parts:were they on?
It was just the fans!
[Was there anything that disappointed you?
Not really!
View detail
Fits: YAMAHA FORCE 155, YAMAHA SMAX, YAMAHA Majesty S
Depends on the rider's preference.
As it is, it is a set of pontoon, but if you change only this, it becomes difficult to ride.
As stated in the product description, the angle of the Torque Camshaft groove is much lower than OEM and is almost straight.
Therefore, KICKDown becomes strong and it becomes difficult to accelerate.
If I lighten the Weight Roller, the acceleration will be better.
The Quickly feeling didn't work for me, so
Only the Clutch is used and the Torque Camshaft is a different one.
It's a lot cheaper than buying a complete set from OEM.
I think it depends on the Setting and the rider's preference.
View detail
Fits: YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA Cygnus X, YAMAHA BWS125 (Bewith), YAMAHA BWS125 (Bewith), YAMAHA BWS (Bewith), YAMAHA BWS (Bewith), YAMAHA Axis Street, YAMAHA Majesty 125, YAMAHA Cygnus Z, YAMAHA Axis Street, YAMAHA Majesty 125, YAMAHA Cygnus Z
I bought the lightweight version.
I bought the lightweight version.
Is the acceleration maybe better? I think so.
But the top speed dropped so much.
View detail
Fits: YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X
Replace regularly.
The Clutch Spring seems to have broken, so we disassembled it and found a scratch in the Pulley and the Weight roller is also in the Quantity:2pc. The set was cracked.
I decided to change the Belt at the same time, and the Quantity:Buy the set product.
The original weight roller was 9g and this product's weight roller is 10g, so shifting is faster.
The top speed seems to have dropped slightly and the hills are a bit slow.
There is no problem for normal driving.
View detail
Fits: SUZUKI LETS4Palette, SUZUKI LETS5, SUZUKI LETS4Basket, SUZUKI LETS4, SUZUKI LETS4Palette, SUZUKI LETS4Palette
Pulley and Belt can be used, but
Pulley and Belt are available.
I think it's worth it just to buy two items.
The Weight roller/Slide Piece is not worth using!
Rather, using it will hurt Pulley.
Pulley can be used for processing!
View detail