Reviews
Fits: YAMAHA Super Jog ZR, YAMAHA SUPER JOGZ, YAMAHA AXIS 90, YAMAHA JOG (2Cycle), YAMAHA JOG (2Cycle), YAMAHA JOG (2Cycle), YAMAHA JOG90
4JPAPRIO is now attached.
The Center Stand for 4JPAPRIO that was given to me was wobbly, so I bought it FOR REPLACEMENT.
Webike's site does not list it as an applicable model, but KN Kikaku's site lists it as an applicable model.
4JP does not guarantee the suitability of Webike, so you are on your own, and if you have any questions, you should contact KN Planning directly.
I have no particular problem using it.
Installation requires a bit of hang, but you can find a lot of information if you search.
In my case, I had a separate Side Stand, so I worked standing on the Side Stand, but for those who only have the Center Stand, I think it is better to work by standing it on the wall etc. while protecting it from damage.
However, it is difficult to work from the Left if it is standing up.
When removing the spring, it is easy to make it move easily with CRCetc., pull out the pin with radio pliers, put the Penetrating Driver on the shaft, tap the shaft lightly with a hammer, pull out the shaft, and finally remove the spring.
(Be careful not to interfere with the Rear Brake Wire and Shaft.)
If two people can work on it, it would be easier to install the spring first, then put the pin through the spring from the left side, one person should hold the right end of the stand and align it while extending the spring, and the other person should apply the penetrating driver from the left side and tap the spring lightly with a hammer. The other person should hold the Penetrating Driver from the Left and tap it lightly with the Hammer.
Since it is not possible for one person to do this, you need to install the STAND first, hook the spring to the body side, put the other side through a long slotted screwdriver, put the tip of the screwdriver near the base of the spring attachment part on the STAND side, and slide the spring while stretching it using the lever principle. Then, using the lever principle, slide the driver near the base of the spring on the STAND side, and hook the spring.
I used the OEM spring only because the notch where the spring hooks was narrower than the OEM spring and it was difficult to install. Therefore, I gave it 4 stars.
View detail
Fits: YAMAHA BWS125 (Bewith), YAMAHA BWS125 (Bewith), YAMAHA BWS125 (Bewith), YAMAHA Cygnus X
Stylish Design
[How is it used?
Touring and city use.
It's been a Motorcycle for 12 years.
The steel parts began to rust.
I had to make do with a Touch pan.
With STAND, every time you park your bike, it gets scratched.
The game of weasel.
Further rust is contained in the water droplets.
When scattered, it can cause damage to non-rusty areas.
I bought it because I thought it would be bad if I didn't.
Was the one you received as per Image?
The length is also the same as the OEM's.
I was able to install it with peace of mind.
The inclination of the Side Stand is also
It's just like it's always been.
No rattling.
Design is slim and Sharp.
In a way, you're used to OEMs.
It may not be reassuring, but...
Where there seems to be no stability.
Intend to use Center Stand.
Was the installation difficult?
SE462 Taiwan's 5th season.
Unlike the structure picked up on Net
Reverse side (Inside Cowl) The deepest part of the
There is a BoltHead and
Bolt removal can be done by
It was difficult to get the tools in and had a hard time.
Bolt uses OEM.
How was your experience with it?
The feeling of the product is light.
Anodized indeed!
Put your foot on the OEM Product.
It's missing something like a handle.
Design by Sharp.
When you make a STAND.
They became sensitive to touch.
Although it is called Dual Color
Black and Matte Black
Because it is a combination of
It appears to be almost all Black.
For those who want to look OEM-chic.
Maybe it's a recommendation.
[Included Parts:were they on?
STANDSpring is
SilverStainless Steel.
It came with a Spring.
The OEMSTAND used to be used for the
Titaniumium coated by Other Brand Product.
It has been used without any problems.
View detail
Fits: YAMAHA BW'S 125, YAMAHA BW'S R, YAMAHA BW'S X, YAMAHA BW'S125, YAMAHA GTR 125, YAMAHA GTR AERO 125, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X, YAMAHA CYGNUS X
Parenthesis OK
Tools required.
If you have the tools, you can change it immediately.
View detail
Fits: YAMAHA Super Jog ZR, YAMAHA SUPER JOGZ, YAMAHA AXIS 90, YAMAHA JOG (2Cycle), YAMAHA JOG (2Cycle), YAMAHA JOG (2Cycle), YAMAHA JOG90
Center Stand
Great service. Fits Jog 50 3KY 1994-1998. Same OEM. Perfect! Thank you staff WEBIKE.TH :D View detail
Well made product. Is only about 5mm longer than standard. Red anodising is more of a pinky colour. There was no hole for the side stand switch for the 2017 model grom, easy to mark and drill one. otherwise fitted perfectly.
Well made product. Is only about 5mm longer than standard. Red anodising is more of a pinky colour. There was no hole for the side stand switch for the 2017 model grom, easy to mark and drill one. otherwise fitted perfectly. View detail