Reviews
CT125 was not supported.
I bought it with the naive hope that it would fit ServiceCoupler, but it did not fit at all.
I used only MarkTube, Bullet Terminal and Wiring and discarded Coupler.
View detail
Fits: SUZUKI GSX250R, SUZUKI DL1000 V-STROM250, SUZUKI DL1000 V-STROM250
Something ….
I'm sorry, but this is the price for this.
It is so plain that even I forget that I put it up.
I only notice it when I put Gasoline in.
View detail
It is covered with scratches.
Installed to protect the Meter panel.
It is unfortunate that Film is so easily scratched and the line scratches are all over just wiping off the dust.
I would like to see an improvement in the Material to make it less vulnerable.
View detail
How can I use this...
The bar was installed in front of the handlebar, and I honestly wondered what I should put on this part.... I installed the Smartphone Holder in the opposite direction, and the position of the Smartphone Holder looked good, but this time, it was attached to the bar so that the area around the Meter could not be seen by the bar, I was agonizing over how to make the best use of it, but I decided to just put it on for the time being. View detail
Fits: HONDA glom, HONDA SUPER CUBC125, HONDA MONKEY125, HONDA SUPER CUB110, HONDA CROSSCUB110, HONDA DAX125, HONDA CT125CT110 HUNTER CUB, HONDA SUPER CUBC125
I'd like to see a better inspection.
I was looking at the Option Parts Catalogue and thought it looked good, so I ordered it. When I opened the package and assembled it temporarily, I found that the parts were not aligned with the crankcase, so I looked at the back side and found that one bolt that holds the plate with the KITACO manufacturer's name on it was completely sticking out and touching the case, so I could not install the plate.
I had no choice but to buy an M3 8mm countersunk screw from Home center and reattach it.
I measured the original screws and found that they were 10mm and 5mm, too long and too short. The instruction manual also had M3 in the Parts List but M4 in the instruction manual.
Also, I would like to mention that the rattling of the Change Pedal in the lateral direction affects the pedal. The Up pedal is fine, but the Down pedal is already getting chipped off as the corners hit it.
View detail
![[K・TOUR] Helmet Holder](https://img.webike-cdn.net/catalogue/images/111680/80-564-13200_1_TS.jpg)
Quality is good
The quality is good and the installation was easy even for an amateur. However, I am not sure if it is just my car model or the installation location, but the noise that resonates with the vibration of the engine from near the key cylinder while driving is quite loud. View detail
It is not OEM compatible.
It was Repair Parts for High Solo.
It is not OEM compatible.
View detail
hard to understand
The instruction manual is too hard to understand….
The ease of stepping on it is crazy good. (Lol)
View detail
Fits: YAMAHA ROYALSTAR1300, YAMAHA ROYALSTAR1300, YAMAHA XG250 TRICKER, YAMAHA XG250 TRICKER, YAMAHA SEROW250, YAMAHA SEROW250, YAMAHA SEROW250, YAMAHA XT250X, YAMAHA V-MAX 1200, YAMAHA TX650, YAMAHA SR500, YAMAHA SR500, YAMAHA SR500, YAMAHA SR500, YAMAHA SR500, YAMAHA SR500, YAMAHA SR500, YAMAHA SR500, YAMAHA SR400, YAMAHA SR400
Smaller than OEM
I used it on my YAMAHAXG250 TRICKER and the outer circumference is smaller than OEM.
There were no functional problems and no exhaust leaks, but there was no snagging at all during installation, making temporary fixation very difficult.
View detail
![[K TOUR] USB Power Kit](https://img.webike-cdn.net/catalogue/images/78922/a_1_TS.jpg)
USB Power Kit
It was installed on a 2023 MODEL REBEL 500.
There is nothing wrong with the product itself, but it says to just connect the Wiring, but there is actually no electricity flowing to the connected wire, so I asked the Motorcycle shop and found out that I need a Relay to run electricity to this Wiring.
There is a place to install a Relay under the tank, and a dedicated Relay could be installed and used.
Relay is 38501-MKP-DN1 and is Honda OEMParts.
I think there is another way to connect the power supply, but I think it is better to check if Relay is available before purchasing.
View detail
Fits: KAWASAKI Z900RS-Cafe, KAWASAKI Z900RS, KAWASAKI NINJAH2, KAWASAKI NINJAZX-10R, KAWASAKI NINJAZX-10R
I installed it on a Z900RS cafe 2019 and it was always on.
DriveRecorder - purchased for installation.
Installed on a 2019 Z900RS CAFE VINTAGELime green where indicated. (Exterior changed to Tiger color)
The installation itself was easy, but it was a constant power source.
Once the DriveRecorder is installed, the DriveRecorder is activated even when the power is turned off.
I ended up looking for it on the Tester and it originally came with one ACC mounting location.
It was not necessary.
Maybe it can be used in other years.
View detail
One-touch helmet clip 503-0000220
Used for ARAI's Full face ASTRO-GX.
ARAI has a hook to fasten the excess chinstrap, but it is a tricky thing to put through the chinstrap and is quite difficult. Other K company has something similar, but due to the shape of the bracket, it would be impossible to use without modification.
I have been using it for more than 20 years and it is a good product with durability except for rust. It would be better if the length could be made more compact.
The reason for the low rating this time is that I got a slightly defective product.
One of the movable claws on the female side was sticking at an angle, making it difficult to engage with the male side. 。 HelmetBody was apparently safe as it was picked up in one van, but this is also Shield, which was just purchased and installed. (PROShadeSystem) is covered in scratches and visibility is poor. [Color] It was not usable as Smoke, just Sunshade.
I've blown Silicon spray and messed it up for a while and the movement got better for Large, but it will either recur eventually or get better with wear and tear.
Please do not distribute these items without inspection, as they are life-threatening parts. I am liable for compensation. Shield, I want you to compensate me for the high price.
View detail
Changed from one that draws power from DAYTONA's BrakeLight switch
I had been using a Harness that draws power from DAYTONA's BrakeLight switch, but I replaced it with a Harness that draws power from within the Headlight to refreshing the Handlebar area.
GRAND was taken from the 10mm Bolt under the Horn and the 3-tooth part.
I added a Fuse and installed ETCHarness and USB extraction harness in the Headlight, but it was the Space of Limit. It is troublesome, but when there are many Included Parts:, it might be better to take out the power supply from the Battery under Seat.
View detail
Good color and shape.
I bought it because of its color and shape.
I want to make the commuting groms BlackGold coded, so I installed it as part of that.
However, when I tried to install it, I found that it was the wrong model, and even if it was a JC61, it could not be installed unless it was a Second Type Model. My Grom is in the first term, so I am currently looking for a way to attach it.
View detail
![[K・TOUR] Helmet Holder](https://img.webike-cdn.net/catalogue/images/97787/80x564x28030xa0_TS.jpg)
Helmet hits Exhaust System …Helmet's protective coating peels off.
I purchased KITACO's Helmet lock, which had been out of stock for a long time, because it was back in stock.
Good for those who plan to install single seat cowl.
Seat Cowl must be removed for installation.
The difference between KIJIMA and KITACO is
KIJIMA's Helmet lock is placed next to the Tandem seat.
KITACO Helmet lock is installed next to the tandem bracket.
The ease of installation and feel of the helmet is definitely better with KIJIMA.
KITACO's seems to be attached in a manner of speaking.
KIJIMA is better for those who do not want to apply the helmet to the Exhaust System.
KITACO is cheaper.
View detail
Not much was needed.
I didn't feel the need for it. I don't feel inconvenienced without them. View detail
Looks good
Satisfied with appearance and texture.
But it is hard to see.
View detail
Too hard.
I bought it to improve the footing, but I sit in the front and it doesn't change the footing at all. View detail
Fits: HONDA XR50 MOTARD, HONDA APE 50, HONDA MONKEY, HONDA DAX, HONDA GORILLA, HONDA MONKEY, HONDA CD50, HONDA BENLY50S, HONDA CL50, HONDA JAZZ, HONDA GIORCUB, HONDA solo, HONDA APE 100, HONDA XR100MOTARD, HONDA SUPER CUB110, HONDA DIO, HONDA SUPER DIO, HONDA LIVE DIO, HONDA G DASH, HONDA Giorno
Not much different from OEM
Product Name
KITACO KITACO Super Throttle Set (STH-4)
Item Number
03-1077000
Vehicles
GIORCUB
Number of man-hours
Around 5 minutes
Why did you choose this product?
I purchased the GIORCUB to make the Throttle of the GIORCUB I am currently working on a little more High Solo.
Impressions after using it
To be honest, I didn't feel like I was High Solo.
I still feel that the use of an OEM Throttle body does not allow for a larger take-up diameter, resulting in a more modest slot.
I chose this product because I will be using the OEM Brake lever circumference as is, but if you are only going for High Solo, you probably should not buy it.
If you want the functionality of a High Solo, you should choose a proper High Solo.
▼ Attention
The product is not so large that it can be called High Solo.
View detail
Flexible but floats.
It was a soft Sticker with flexibility.
The adhesiveness is about the same as a regular Sticker etc., so it will come off quickly.
The surface has been degreased, but there is some floating.
The paste part of zx25r is pear skinned and does not adhere well.
It has to be a Type like Cover.
Size is also Small ....
View detail