Reviews
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110-PRO, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA MONKEY125, HONDA DAX125, HONDA glom, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA SUPER CUB 50-PRO
Cheap but good product
I purchased it as a replacement for the original C125. Not only was there not much difference from the original price, but Kitako is a trustworthy brand, so I chose it without hesitation.
The product reviews were good, so I ordered it without even thinking about it. Now the C125 is for life. -------------------------------------------------- -------- I purchased it as a replacement for the original C125. Not only was there not much difference from the original price, but Kitako is a trustworthy brand, so I chose it without hesitation. The product reviews were good, so I ordered it without even thinking about it. Now the C125 is for life. Powered by Google Translator
View detail
Fits: HONDA LITTLE CUB, HONDA BENLY50CD50, HONDA BENLY50CD90, HONDA BENLY50S, HONDA SUPER CUB 90, HONDA SUPER CUB70, HONDA SUPER CUB 50, HONDA SUPER CUB 90, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA CL50
It is fun to try the Best Match with FSprocket!
I always enjoy climbing a certain public road with a 3-speed LITTLE CUB, but 3rd gear is not good at all when the DRIVEN is set at 40 with the standard +1. However, the engine load was too large during the long full throttle sections, and I did not know when the engine would break down. I wanted to give the engine a little more room to rev the engine so that even at 40km/h in 2nd gear, the engine was not at full throttle, so I decided to raise the DRIVEN 2 steps at once to 40, skipping over the standard 39. I didn't have a very good Image at the standard 39 Ding.
So I lowered the Driven to 38 Ding and the result was as I expected at first. I was able to get out of 2nd gear at 40km/h±α without having to go full throttle on every Corner. I was happy to find that I did not have to drop to low even on the tightest Corner climbs, and I did not have to drop Engine RPM on most Corner exits when entering the Corner, so as a result, I was able to drive without spoiling the acceleration feeling too much.
In addition, the engine RPMs are now more generous in 3rd gear on the downhill corner, allowing the driver to enjoy a greater sense of speed when entering the corner.
It's fun to experiment with different FRSprockets and see how they run.
View detail
Fits: HONDA CUB press 50, HONDA CUB press 50, HONDA CUB press 50, HONDA CUB press 50
There are not many varieties.
Rear sprocket was replaced because it was rusted and still wanted to swing to the high speed side.
Since PRO's Sprocket seems to be special, NORMALCUB's Sprocket cannot be installed, so this is installed.
It is close to NORMAL but a little on the fast side.
I am comfortable with KITACORear sprocket, which I use all the time.
View detail
Fits: HONDA SUPER CUB110, HONDA CROSSCUB110, HONDA CT125CT110 HUNTER CUB, HONDA MONKEY125, HONDA DAX125, HONDA glom
Kitako I trust!!
The packaging, condition and quality of the item are all good. However, in the case of JB03 Monkey imported to Korea, the screw hole size does not match, so additional 10-pi expansion work is required. Since it has been converted to 428, I believe there will be more reliable driving force transmission and durability. View detail
Fits: HONDA MONKEY125, HONDA glom, HONDA HRC Grom
Black color Simple
I replaced the front and rear Sprocket with Chain on my 2021 Grom JC92. 1 Driven Sprocket to Long and left the Driven Sprocket at 38 and it seems to run very good for me. The KITACO Driven Sprocket is black, unlike the Normal Sprocket, so the suspension feels tighter. View detail
Fits: HONDA APE 100 TypeD, HONDA XR100MOTARD, HONDA NSR mini, HONDA NSR50, HONDA NSF100, HONDA NS50R, HONDA NS50F, HONDA NS-1, HONDA APE TypeD, HONDA XR50 MOTARD, HONDA NSR80
Balance of practicality and price
We replaced it at the same time when we replaced the Chain on the APE 100TypeD.
The replacement will be from OEMSprocket.
There is no problem in use. If you just want to replace it, installation is easy.
However, if you want to work more precisely when installing the Sprocket on the Wheel, it may be better to have a little ingenuity and a certain level of maintenance skill. However, since there is a lot of play in the diameter of the holes, there is a little less than 1mm of space between the Stud bolt and the Sprocket. Therefore, the center of the wheel and the center of the Sprocket must be aligned before tightening the nut, otherwise the wheel will be shaky in the circumferential direction when it rotates.
I think it is possible to improve the tolerance accuracy of the hole diameter, or to prepare a nut that can be centered in the circumferential direction by making the nut ground surface taper and tightening it, or to have a simple dedicated installation tool for high precision installation. or a simple dedicated installation tool would allow for highly accurate installation.
The material is steel, but the surface is coated with a black coloring, so it can change the atmosphere from the OEM-like silver iron.
View detail
Fits: HONDA CHALY 70, HONDA XL80, HONDA CHALY 50, HONDA XL50, HONDA CB50, HONDA XE75, HONDA XE50, HONDA R&P, HONDA XR80, HONDA MOTRA, HONDA MONKEY R, HONDA MONKEY RT, HONDA JAZZ, HONDA DAX, HONDA DAX70, HONDA Nauty Dax, HONDA GIORCUB, HONDA APE 100, HONDA APE 50, HONDA MAGNA50
I appreciate the Lineup of each tooth number of Sprocket with old car gaiters.
The 50CCE engine was replaced by the 100CCE engine, and the Sprocket was installed to increase the speed. This type of KITACO's Sprocket has a lineup of teeth and is very useful even though it is for an old vehicle. View detail
GSX-S125Driven Sprocket replacement
I swung from an OEM 45 to a Short, which is one up. I thought there would not be much change, but the Torque was increased quite a bit. I often stop and go in the city, so it became quite easy to ride. The ministry was Cospa Large. View detail
Fits: HONDA XL50, HONDA XR80, HONDA XL80, HONDA XE75, HONDA XE50, HONDA R&P, HONDA CB50, HONDA CHALY 50, HONDA CHALY 70, HONDA JAZZ, HONDA DAX, HONDA DAX70, HONDA Nauty Dax, HONDA MOTRA, HONDA MONKEY R, HONDA MONKEY RT, HONDA APE 50, HONDA APE 100, HONDA GIORCUB, HONDA MAGNA50
I still appreciate the variety of Sizes.
I bought it to make 5TSmall Rear sprocket for my old Motorcycle, but it was too big for the Chain tensioner, but I was happy to use it without packing the Chain. View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110-PRO, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA MONKEY125, HONDA DAX125, HONDA glom, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA SUPER CUB 50-PRO
Good
Sau 1 tháng trải nghiệm thì sản phẩm này rất tuyệt nhẹ và cứng lớp sơn phủ vững chắc không có dấu hiệu gì cả ăn khớp mượt mà với sợi sên ---------------------------------------------------------- After 1 month of experience, this product is very light and hard -working painted with solid coating without any signs of smooth joints with slugs Powered by Google Translator View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110-PRO, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA MONKEY125, HONDA DAX125, HONDA glom, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA SUPER CUB 50-PRO
be cheap and good
Monkey jb03 version needs to be machined because the genuine wheel sprocket bolt is 10mm. The Kitako sprocket is 8 mm bolt size, so it needs to be machined to widen the hole with a drill View detail
High performance not only Sprocket with good durability.
For the test from 30 NORMAL Rear to 29 Short Specification, we changed to KIJIMA's Sprocket this time.
The Sprocket to be replaced is steel, but it is a few 10g lighter than the NORMAL one. Is it because of the parts under the spring?
There was almost no runout and it turned beautifully. I can say that this performance at this price is too good to be true.
To replace the Sprocket, simply remove the Rear wheel, remove the Rear sprocket fixing bolt, and replace the Sprocket to be replaced.
The Bolt side where the Sprocket is installed will probably be pushed by the Sprocket at the moment it is installed, and will be concaved into the middle of the Wheel. After tightening the bolt nut fixing the Sprocket, fix the nut with the locking plate.
There were no problems with operation checks, and the work was completed easily and simply.
The Torque drop on climbs, which we were worried about, was not a concern, and in town, the RPMs were as pleasant as ever compared to the NORMAL, and there was no Torque drop at top speed in the round-the-clock practice course measurement.
The same is true for descending mountain passes, and the negative pressure of engine braking is also lessened in downshifts.
After the replacement, the Corner ring has a slightly milder feel to it, but this is actually easier to ride and makes it easier to enter the Corner.
Meter errors were also corrected from the NORMALHappyMeter to the actual measured values, resulting in an almost accurate display of speeds.
Black color also looks good with the gold chain.
View detail
Fits: KAWASAKI Z250 (2013-), YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA YZF-R25, YAMAHA YZF-R25, KAWASAKI Z250SL, KAWASAKI Z250SL, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R25, KAWASAKI NINJA2 Helmet50RR, KAWASAKI NINJA250R, KAWASAKI NINJA2 Helmet50RSL, KAWASAKI NINJA2 Helmet50RSL
Steel and good cosmetics
This product is the only one in this price range in the Steel & Black color Sprocket (*).
(Quality, such as texture and paint quality, is commensurate with price; roughness is visible in Edge machining accuracy and paint uniformity.)
The SUNSTAR Sprocket (JK-102-44), which is 2,000 yen more than this item, is also black in the image, but the actual item appears to be silver. Around 5,000 yen, Steel, Black color Then, I have no choice but to select this product....
Vehicle:Ninja 250 (JBK-EX250L)
View detail
Fits: HONDA XR50 Motard, HONDA APE 100 TypeD, HONDA APE TypeD, HONDA XR100MOTARD, HONDA NSR mini, HONDA NSR80, HONDA NSR50, HONDA NSF100, HONDA NS50R, HONDA NS50F, HONDA NS-1
KITACO Driven Sprocket (Rear)
About quality and texture Kitaco Sprocket has a really good quality About the feeling of use I'm still collecting the ape100 disc parts, so I'm not using it, but the kitaco kitaco sprocket is reliable Products to buy together none Difficulty of installation It can be tough without a bike rack Cost performance and comparison with other products The quality and price are more reasonable than other products About shipping and packaging It took a week and the packaging is great Any concerns, cautions, or advice when purchasing The product installed in my app100 is also Kitaco, and it is working well without any problems This product is the best, and everyone knows it's reasonable View detail
Fits: HONDA LITTLE CUB, HONDA SUPER CUB 50, HONDA SUPER CUB 90, HONDA BENLY50CD90, HONDA SUPER CUB70, HONDA BENLY50CD50, HONDA BENLY50S, HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA SUPER CUB 90, HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA CL50
Good durability
[How is it used?
For Sprocket Replacement
How was your experience with it?
Steel and heavy lol.
However, I think it is quite durable
It's a commuter car, so this is good enough.
How did it compare to other products?
[Points to note]
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
View detail
Fits: KAWASAKI Z250 (2013-), YAMAHA MT-03 (2015-), YAMAHA MT-25, YAMAHA YZF-R25, YAMAHA YZF-R25, KAWASAKI Z250SL, KAWASAKI Z250SL, YAMAHA YZF-R25, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA YZF-R3, YAMAHA MT03, YAMAHA YZF-R25, KAWASAKI NINJA2 Helmet50RR, KAWASAKI NINJA250R, KAWASAKI NINJA2 Helmet50RSL, KAWASAKI NINJA2 Helmet50RSL
Let's start with the iron.
I use SL for Circuit, commuting, Gymkhana and many other purposes.
I'm buying more to get the Final = reduction ratio I was aiming for with a certain Circuit.
In the case of the above applications, the decision is rarely made after a single change, but rather multiple trials are required, and the Sprocket to be used will naturally change as the time increases or the running style changes.
But Material:In the case of Aluminum, the prices are high, so we can't have so many.
In such cases, KITACO's steel Sprocket is relatively inexpensive and is recommended for experimental purchases.
I have used it not only on SL but also on NSR50 etc.
I think there is, well, KITACO, since it is a rich Lineup.
However, since I use it only for such purposes and frequently change it to another Sprocket, I cannot make a long-term Life judgment.
It seems to wear a little fast from what I can see, but maybe that's just my imagination lol.
Use this Sprocket to determine the number of ding you want to use, then Material:I think it would be better to change to Aluminum things to avoid unnecessary expenses.
View detail
Fits: HONDA LITTLE CUB, HONDA SUPER CUB 90, HONDA BENLY50S, HONDA BENLY50CD50, HONDA BENLY50CD90, HONDA SUPER CUB70, HONDA SUPER CUB 50, HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA SUPER CUB 90, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA SUPER CUB 50, HONDA CL50
CUB Rear sprocket
I bought this product because it was cheaper than buying OEM Product.
I haven't used it yet, but I'm looking forward to seeing how long it will last.
View detail
Fits: HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110-PRO, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA MONKEY125, HONDA DAX125, HONDA glom, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA SUPER CUB 50-PRO
Best
I love Kitaco sprocket. First thing is quality. Second affordable price and most of the Kitaco stuff for my grom is look good easy install View detail
Fits: HONDA Ape 100, HONDA GIORCUB, HONDA JAZZ, HONDA CHALY 70, HONDA CHALY 50, HONDA APE 50, HONDA XR80, HONDA XL80, HONDA XL50, HONDA XE75, HONDA XE50, HONDA R&P, HONDA CB50, HONDA MAGNA50, HONDA MONKEY RT, HONDA MOTRA, HONDA Nauty Dax, HONDA DAX70, HONDA DAX, HONDA MONKEY R
GEAR ratio adjustment after Bore up
I purchased this GEAR ratio in order to lower the GEAR ratio. This time, I replaced it with Driven Sprocket on the front side due to the target maximum speed. The quality of the Sprocket is good and it was installed without any problem. View detail
Fits: HONDA MONKEY BAJA, HONDA MONKEY, HONDA GORILLA, HONDA MONKEY BAJA, HONDA GORILLA, HONDA MONKEY
KITACO is the best!
KITACO's Sprocket is Black on the rear and Silver on the front! The front is Silver! It's not as good as Takekawa or GCraft, but it's better than those! My top speed has changed by 5km! Thank you KITACO! View detail