Reviews
For Wiring of Race Vehicles
I purchased Wire to match Race regulation.
Wires also come in different thicknesses, and although thicker wires are fine for the drain bord and filler caps, fine places such as the split pins of Caliper cannot be wound with thicker wires, so we purchased thinner wires.
Since it is long enough to last almost a lifetime, I think it is cosmetically sound because once you buy it, you will be able to use it for quite a long time.
View detail
Cosmo
The accuracy of the Sprocket is lower than that of other companies' Sprocket. (The difference between where the Chain is stretched and where it is not is large.)
However, if you take this into consideration and Chain tension the product, I think it is a good cosmetic product.
View detail
Fits: SUZUKI GSX1400, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI GSR400, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI ZX-6RR, KAWASAKI ZX-6R, KAWASAKI Z1000 (water-cooled), KAWASAKI Z1000 (water-cooled), KAWASAKI Z1000 (water-cooled)
If only it were a little cheaper…
I am purchasing this because I need it to replace the Slip-on Silencer.
The quality is fine and it prevents exhaust leaks well, but it is a consumable item and I would like it to be a little less expensive.
View detail
Fits: HONDA NSF100, HONDA NS50R, HONDA NS-1, HONDA NS50F, HONDA APE 100 TypeD, HONDA NSR mini, HONDA XR100MOTARD, HONDA NSR50, HONDA APE TypeD, HONDA XR50 MOTARD, HONDA NSR80
Rear Sprocket replacement
The Rear of the installed product seemed to be getting a little sharp, so I bought this new one to replace it with a new one along with replacing the Chain with a new one.
The price was not that much, which was helpful.
It looks Black and does not look bad.
View detail
Fits: YAMAHA GRAND MAJESTY400, YAMAHA TT250R RAID, YAMAHA TT250R
Used for WR155
[How is it used?
I used it to replace the YOSHIMURAExhaust System on my WR155.
How was your experience with it?
It is usable without leaks of exhaust Gas.
How did it compare to other products?
I have never used KITACO and OEM, but KITACO quality is close to OEM quality.
[Points to note]
If not tightened firmly, it will leak.
Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
nothing special
View detail
For Motorcycle commuting to school
Purchased for Motorcycle to use to get to school in the rain. Never used.
Tools are not objects, so the molding is what it is.
View detail
I only want Harness.
MONKEYJB03's Temperature SensorHarness (Extension) I wanted to buy only one, but there is no such sale, so I bought this product.
I think it's because Harness alone is not good for business.
I know I had no choice, but I would have preferred to sell it as a Single Body if possible.
View detail
Fits: HONDA APE 100 TypeD, HONDA XR100MOTARD, HONDA NSR mini, HONDA NSR50, HONDA NS50R, HONDA NSF100, HONDA NS50F, HONDA NS-1, HONDA APE TypeD, HONDA XR50 MOTARD, HONDA NSR80
Affordable Trial
Prepared for the expedition.
When going to an unusual Circuit, it is often necessary to change the final gear ratio by changing the number of Sprocket Dings.
In many cases, it is a gamble, and it is rarely decided in one shot.
So, it is good if you can read the number of hits to some extent (e.g. information from regulars), but if not, you have to run and test it by yourself.
This time, compared to the usual Home, it will be a large width and high speed course, so it is almost impossible to predict how many pins will be used.
Material:The lightweight Aluminum Sprocket is obviously better, but I don't want to waste money buying a bunch of products that I don't know if I will use in the future, so I always use the Iron Sprocket made by KITACO to test it.
Strictly speaking, the heavier weight will have some effect on the driving characteristics, but I don't have that SEVERE sensitivity, so it's not a problem lol.
I was too Long for the results lol.
Still, it is useful for TEST purposes for the future.
View detail
Fits: HONDA CRF250M, HONDA CRF250L, HONDA CBR250R, HONDA CB250F
usually
I don't know because I had it installed, but I wish it had been included with the purchase of the exhaust pipe. View detail
Fits: HONDA NSF100, HONDA LITTLE CUB, HONDA CB50, HONDA glom, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA CROSSCUB110(FI Vehicles), HONDA CROSSCUB110(420Conversion), HONDA CROSSCUB110(420Conversion), HONDA SUPER CUB110-PRO(FI Vehicles), HONDA SUPER CUB110PRO, HONDA SUPER CUB110(FI Vehicles), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110(420Conversion)
Purchased to replace Driven Sprocket and Chain and 3 other items at the same time.
The standard 14T was replaced with a 15T and the Driven Sprocket was replaced with a 33.
As for Image, it looks like Drive was changed to 15.5 Ding.
The RPMs were lowered, so the fuel consumption was up 5 km.
The first gear can now be handled like a normal Motorcycle.
But as the Shop Owner said during installation.
OEM has anti-vibration Rubber, but this one does not.
He said that the running sound would change.
This is especially noticeable at low speeds. It is a clatter from toot-toot.
What do you want from a CUB?
This is what I felt most after the exchange.
Personally, I plan to return to the OEM standard 14T and 34-ding next time.
View detail
Protection.
I purchased this product to protect and prevent scratches and scuffs on the Exhaust System part.
It is thick and seems to be heat resistant, so I am installing it with high expectations.
I hope it will be somewhat durable, sticky, and long lasting.
If the size were a bit larger and cheaper, it would be helpful for consumables.
View detail
Maintenance
I purchased this product for maintenance of Clutch Wire. View detail
Fits: HONDA NSF100, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA glom, HONDA CROSSCUB110(FI Vehicles), HONDA CROSSCUB110(420Conversion), HONDA CROSSCUB110(420Conversion), HONDA SUPER CUB110-PRO(FI Vehicles), HONDA SUPER CUB110PRO, HONDA SUPER CUB110(FI Vehicles), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110, HONDA APE 100 TypeD
I raised it from 12T to 13T and 13T to 14T.
I went from 12T to 13Th to lower the Engine RPM when driving. I went from 13T to 14T to lower the RPM a little more. Now I can cruise 60km before the engine roars even on a moped. Of course, it is only a moped when going uphill.
When I bought it, I noticed that the Washer shape is different between Takegawa and Tokico (the position of the Bolt hole and the notch to enter the Spline are reversed), so it cannot be fastened without using the Washer included in the package.
View detail
Good cosmetics if you don't take it on and off often.
[How is it used?
Used on OEM Exhaust pipe and Silencer joint of MainMotorcycle's XJR1300C that had been inspected.
The Exhaust System itself is the same as the normal XJR1300, so Gasket could be used normally.
How was your experience with it?
The exhaust leaks were normally prevented, and this black shiny joint gasket from KITACO was able to keep the exhaust from leaking once it was used.
Even if successfully removed, it is basically non-reusable. This is a type of Gasket that is quite crushed and sealed.
How did it compare to other products?
I decided to go with KITACO because the OEM Product costs 2300 yen.
However, the OEM gasket is a metal type that can be used over and over again as long as the shape does not get messed up when tightened.
I think they are essentially disposable. In fact, it can be used normally.
So it is cosier to buy OEM if you have to wear it on and off a lot.
[Points to note]
Anyway, Gasket sticks to it and I can't peel it off. I wish you could do something about this.
Even if I wanted to make a new Gasket, it just falls apart and won't come off at all.
Can it be removed quickly if I apply something to it before installation?
View detail
Fits: HONDA LEAD110 EX, HONDA LEAD110, HONDA BENLY50110 PRO, HONDA BENLY50110, HONDA BENLY50 PRO, HONDA BENLY50
passing mark
It gets dirty very quickly, and the air cleaner replacement is several times benly50110
The air cleaner I am currently working with from KN Planning is about 105% larger than STD and I had to shave a lot to get it to fit, so I felt bad and wanted to try another company, so I bought KITACOBrand.
As a result, KITACO was 97% of STD, so it fit perfectly, but the position of the fixing hole was also on the inside, so we had to widen the hole a little.
Well, Quantity:Pair (for Left and Right) It's only about 1mm each, and since it's plastic, it's easy to process, so if you're willing to do it, it's a good idea.
However, there is no doubt that OEM is the best when it comes to air cleaner for Benly50.
View detail
Fits: HONDA CUB press 50, HONDA CUB press 50, HONDA CUB press 50, HONDA CUB press 50
For maximum speed UP!
Since CUB's Engine is limited, I aimed to increase the maximum speed with Final. The effect is so-so. View detail
Fits: HONDA CRF250M, HONDA CRF250L, HONDA CBR250R, HONDA CB250F
When replacing the Exhaust System
[How is it used?
It was used for Exhaust System replacement.
Was the one you received as per Image?
As per Image.
How was your experience with it?
Not too much, not too little. Excellent cosmetics.
[Points to note]
None in particular
How did it compare to other products?
I have not used any other products.
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
Fits: HONDA LITTLE CUB, HONDA LITTLE CUB, HONDA Monkey Baja, HONDA MONKEY RT, HONDA MONKEY R, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MONKEY, HONDA MOTRA, HONDA MAGNA50, HONDA MAGNA50, HONDA CL50, HONDA BENLY50CD50, HONDA BENLY50CB90, HONDA BENLY90 S, HONDA BENLY50S, HONDA CUB PRESS, HONDA CUB PRESS, HONDA CUB PRESS
Quantity:1 Set of 2pcs. and inexpensive.
I used it on a LITTLE CUB and the size is perfect, no problems. View detail
Fits: HONDA NSF100, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA glom, HONDA CROSSCUB110(FI Vehicles), HONDA CROSSCUB110(420Conversion), HONDA CROSSCUB110(420Conversion), HONDA SUPER CUB110-PRO(FI Vehicles), HONDA SUPER CUB110PRO, HONDA SUPER CUB110(FI Vehicles), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110, HONDA APE 100
Let's change it if we're going to Bore up! (^^ゞ
KITACO's have holes in them, so they're lightweight and provide heat protection! View detail
Fits: Others KEIHIN(KEIHIN)PWKΦ28MCarburetor, Others KEIHIN PWKΦ28Carburetor(Old type), Others KEIHIN(KEIHIN)PEΦ24Carburetor, Others KEIHIN(KEIHIN)PEΦ22Carburetor, Others KEIHIN(KEIHIN)CRMINIΦ22Carburetor
Perfect if you want to change PWK's Chalk.
Product Name
KITACO KITACO Choke Cable Assembly
Item Number
905-1122900
Vehicles
GIORCUB
Number of man-hours
About 10 minutes
Why did you choose this product?
We have prepared a Chinese YD Chalk, which is attached to the GIORCUB we are currently working on, so that it can be pulled from the outside.
Impressions after using it
This chalk will return to its original position as soon as it is pulled, so it is necessary to keep pulling when applying the Engine.
It eliminates the Chalk pull, but I felt it was not as user-friendly as it could have been.
However, installation is easy and the Wire is long, so there seems to be some freedom in the mounting and fixing position.
I would recommend it if the Chalk is hidden by the body of the car as I am.
▼ Attention
Chalk will return on its own, so it must be kept pulled at all times.
View detail