Reviews
Super fuel hose set I.D.Φ3×1m
Used for carburetor overflow hose
I bought Pink last time but 1m was not enough so I bought more.
I decided to use a two-tone color anyway, so I went with Green this time. It is now easier to visually inspect each cylinder.
Now we can also verify which one is more durable. v
Compared to Pink, which is squishy and easy to handle, Large is harder. It is almost as hard as a normal Vinyl type.
Pink is easier to handle (it is soft and stretchy, so you can get a little bit of mouthfuls in the SizeOver area), but either is fine for Overflow.
Green is recommended for use in areas with tight bends, where the pipe is not easily crushed.
As a side note, I always reserve KITACO's Package (plastic) because of the above etc.
It can be used to make a washer for the gap between the clutch lever and holder when there is more play between the clutch lever and holder, or to make a collar to prevent sticking between the accelerator grip and switch holder. And it's free.
View detail
Super fuel hose set 991-0311000
Used for Carburetor lower overflow hose.
This is the case in the Parts List. (mk? was it?) I thought the inner diameter was 3.5mm, but the alternatives from Company P and Company D were also 3mm, and KITACO did not have half as many, so I bought 3mm. KITACO also did not have a half-decent number, so I bought the 3.5mm. I bought a 3.5mm diameter pipe because it is soft and easy to use.
I liked the Pink color, although the slightly firmer Green would be better for Flow Hose.
When I tried to replace it, I discovered the problem:1m is Quantity.:I can only take 2pcs.
Plans to reorder. I'll have to write another tiresome impresario. I have no time to be poor.
Should we try a Pink/Green two-tone color at this point?
View detail
Since it interferes with
I used to use a fuel cock from company T, but it didn't last six months and leaked even when the cook was turned off, so I decided to buy a KITACO fuel cock.
If it leaks in a short period of time, buy OEM like Large people.
The cook outlet can be selected to be forwarded, which is nice because it eliminates interference even if a big carburetor is installed.
View detail
Satisfied
Good cost with 3 different sizes View detail
Easy to use
The ZOOMER OEM fuel hose has a 4.5mm inner diameter, so I could not find the same system in Other Brand Products. I used this product and a conversion joint to install it. The product is inexpensive and easy to purchase, but it is difficult to know if the installation is good or bad without actually assembling such a product. View detail
Easy to use
It has moderate flexibility and is easy to use. I've used it on old Breeder, Fuel Hose, etc.
The translucent design made it easy to check the condition of the inside.
View detail
exchange
The DrainHose was dirty, so I bought it FOR REPLACEMENT.
It is a tube with high Gasoline resistance, and this tube is soft to some extent, and it is a purchase because the evaluation seemed to be good. It is certainly soft and nice, but I wish I had a transparent soft Gasoline resistant tube instead of Pink.
View detail
Purchased in conjunction with DAX carburetor replacement
I bought this to go with my American Ducks carburetor replacement.
In order to install this product, I drilled a hole of about 6" on the body side and installed it.
I found the transition to be a little firm.
View detail
It's safe and easy to use.
Useful for Fuel Tank and Carburetor removal and maintenance. 3 different types of plugs are available in quantity to match the hose's large size:Set and convenient. View detail
It's easy to check the status of Fluid.
The inner diameter of the Breeder and Hose is exactly the same, so there is no need to worry about it falling out, and the translucent design makes it easy to check the air condition. You can cut the hose to any length you want. View detail
To MONKEYYOSHIMURAcarburetor!
I bought this one because the fuel hose was short and became hard The new one is still soft and easy to install View detail
It got hard and I had to replace it!
I bought a replacement because it got hard and old I can use it next time for Repair as it is quite long It's a manufacturer's item so you can use it with confidence View detail
A little hard?
I also bought Pink, but Green Light is a little firmer
You may not expect more weather resistance than the OEMs, but you can shorten the maintenanceSpan If you do, you should be fine
I would like to continue to use FuelLine because it's transparent and I feel more secure in my mental health It is
View detail
I always buy them regularly
CR Carburetor is Exactly to the Fuel Joint part of the Gasoline I like to be able to see the flow If you don't flush Gasoline for years of use or OFFSeason, the Hose will harden and I feel like I'm going to buy it then View detail
Is it reasonable?
When Fuel Cock was set to Reserve, it seems that rust accumulated suddenly Jet got clogged suddenly and cleaned but because I can not afford to clean the Tank I put Filter as a temporary measure for the time being!
It is safe for the time being because rust is tightly cut off!
I think that you can check the accumulation state because it is transparent!
View detail
KITACO Super Fuel Hose Set
Pretty ok for the price. Discolours pretty fast, so it turns yellow/red after awhile, depending on what gasoline you use. Am also using this as a breather hose, and it works fine as that. View detail
As a consumable good enough
Hose always buys this.
It will cure in the end.
It is not that expensive and the Length is as it is.
It also comes with a Clip so you will not have to buy it one by one.
View detail
Harley's split Tank convenient for removal
Harley's split Tank is convenient for removing. If it is an OEM, Hose is connected to the bottom side of the Tank, but once you removed one, you had to pull out Gasoline once, but if you do this you can remove it without having to remove Gasoline and it is useful for Maintenance. However, because it is Plastic, I'm wondering if the durability is Large durable.
Also, is there a way to structure that gasoline spills a little when removed.
View detail
With carburetor exchange ...
This part is necessary when exchanging carburetor with DAX! It is easy to install, but I wanted a manual of where to connect which Hose ... But price is good, Cost performance is high! View detail
Because it is an old SR - - -
Since there is a possibility that there is rust, rust on Tank, I installed it. I think that making is suitable for price.
I installed TMR-MJN 40 of YOSHIMURA but it is good without shortage of Gasoline at full throttle.
I will look at how the garbage can take in the future. I think that Large change is economical in exchange as soon as the price is cheap because it is cheap.
View detail