Reviews
Fits: HONDA glom, HONDA glom, HONDA MONKEY125, HONDA MONKEY125
While we're at it ClutchO/H
My jc92 grom girl.
The clutch started to slip after 8000km, probably because I am running the car at full throttle on mountain passes, so I decided to replace it with a reinforced clutch set from Endurance.
Net says OEM Lifter is chipped, so buy it.
Lifter was no problem, but the legs of the Pressure plate are WW.
I ordered OEMPlate anyway.
I would like to have a reinforced type pressure plate.
View detail
Clutch weight reduction
When I go touring for a day with Small Engine Displacement Volume every time, the number of times I grip the clutch exceeds 500~1000 times in the habit of raising it to 6th gear immediately, so when I return home, my grip strength will be gone.
Although it was anxious whether or not it would be attached to the special machine called Gilera CX125 in appearance and Suzuki Wolf 200 in content, somehow Setting completion.
At first, the setting was too severe, and the Large was strange because it idled even if the Clutch was connected, and the half-clutch continued even if the Clutch was turned off.
Clutch wire adjustment is increased from 2 to 4 positions.
If you can do the setting by yourself, I recommend it because it is quite effective for the Machine that Clutch is heavy and Large strange!
I wish I had noticed the product sooner and put it on…
For your information.
With the Motorcycle standard playful Wire handling, you will definitely be out of Setting range.
It is possible to start setting by eliminating 1mm of play as much as possible.
If you understand how the Clutch works and have the patience, it will be Large sturdy.
View detail
It is wonderful to incorporate this mechanism into this Size
The first thing we must say is to say that it is wonderful to make this mechanism a product at this large price, this price.
(On the principle of Lever) It will be hard to install if the load gets lighter, Stroke gets longer, the screw is not tightened, it is fastened by Material elongation, unless you understand the machine.
If you do not understand this meaning, let's ask PRO. (I am not a mechanic, but it is a PRO of mechanical equipment design, processing, assembly)
RubberBoots' durability is low, it may be inevitable for this lot production. How can such things be made with our ingenuity.
[Mounting Machine]
YAMAHA TDM850 1999UK 4TX
[Installation result]
37% decrease (Pivot pinCenter) It's set, and it got lighter than it in terms of bodily sensation.
Although Stroke got longer, there was no slippage of Clutch, Clutch could not cut so much that Neutra would not come out.
OEMClutch Cable Attachable in the range of play adjustment screw included.
[impression]
Clutch became lighter, operation became smooth and easy to handle.
Because we are accelerating Release, this is just fine and just fine.
[Mounting]
Light clutch's Cable play adjustment (What about the picture? Tighten up to the end end by hand (Wrench is not used)
Adjust play of Clutch lever holder (In the picture?) , Light clutch input side Quantity : Pair (for Left and Right) Use for adjusting Clearance.
Clutch meatPoint, the recipient of Crankcase (Photo?) Adjust with.
There is no play of Cable at all. Where PullLever starts.
In Light clutch, I added the Grease of Mochuru. Cork is running Fork oil # 10.
The play adjustment screw portion on the Clutch Cable side was hard to enter because the attached Rubber Boots was hard, so protected with WaterproofTape.
Since Cable is surplus, we changed the handling to the outside of Fork.
[How I ride]
Make circle with forefinger and thumb and surround Grip (Index finger between Grip and Lever)
Pull Clutch lever with middle finger and ring finger. ,
Clutch is switched off only when starting, gearshift is half Clutch.
Release at the time of shifting is open at a stretch.
Because fingers are long, Clutch meatPoint is far away.
View detail