KITACO Motorcycle Drive Parts Reviews

Filter

Write a review and get Webike Points!

Reviews

KITACO

23 Feb 2024

Driven Sprocket (Rear)

Fits: HONDA NSF100, HONDA NS50R, HONDA NS-1, HONDA NS50F, HONDA APE 100 TypeD, HONDA NSR mini, HONDA XR100MOTARD, HONDA NSR50, HONDA APE TypeD, HONDA XR50 MOTARD, HONDA NSR80

Japanese Webike user

3/5

Rear Sprocket replacement

The Rear of the installed product seemed to be getting a little sharp, so I bought this new one to replace it with a new one along with replacing the Chain with a new one.
The price was not that much, which was helpful.
It looks Black and does not look bad. View detail

KITACO

11 Oct 2023

Reinforced Clutch Spring Set

Fits: HONDA LEAD125, HONDA DIO110, HONDA PCX150, HONDA PCX150, HONDA PCX150, HONDA PCX125, HONDA PCX125, HONDA PCX125, HONDA PCX125

Japanese Webike user

3/5

Did I change my mind? It was about the same.

I replaced it with a Belt replacement to see if it would increase acceleration in the early stages of launch. Although it is not compatible with the Belt, I checked carefully to make sure that it could be installed. As a result, I was able to install it without any problems.

The RPMs at which the clutch connects may have increased slightly. The speed at which the clutch was connected was about the same as the speed at which the clutch was connected.
It was out of conformity, so Spring rate may not be appropriate.

The Belt, which was replaced at the same time, caused the Engine RPM to drop a little when shifting throughout the entire range, and this caused a sluggish feeling.

It has nothing to do with Clutch, but.... View detail

KITACO

16 Aug 2023

Driven Sprocket (Rear)

Fits: HONDA APE 100 TypeD, HONDA XR100MOTARD, HONDA NSR mini, HONDA NSR50, HONDA NS50R, HONDA NSF100, HONDA NS50F, HONDA NS-1, HONDA APE TypeD, HONDA XR50 MOTARD, HONDA NSR80

Japanese Webike user

3/5

Affordable Trial

Prepared for the expedition.

When going to an unusual Circuit, it is often necessary to change the final gear ratio by changing the number of Sprocket Dings.
In many cases, it is a gamble, and it is rarely decided in one shot.
So, it is good if you can read the number of hits to some extent (e.g. information from regulars), but if not, you have to run and test it by yourself.

This time, compared to the usual Home, it will be a large width and high speed course, so it is almost impossible to predict how many pins will be used.

Material:The lightweight Aluminum Sprocket is obviously better, but I don't want to waste money buying a bunch of products that I don't know if I will use in the future, so I always use the Iron Sprocket made by KITACO to test it.
Strictly speaking, the heavier weight will have some effect on the driving characteristics, but I don't have that SEVERE sensitivity, so it's not a problem lol.

I was too Long for the results lol.
Still, it is useful for TEST purposes for the future. View detail

KITACO

04 Aug 2023

Front Sprocket

Fits: HONDA NSF100, HONDA LITTLE CUB, HONDA CB50, HONDA glom, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA CROSSCUB110(FI Vehicles), HONDA CROSSCUB110(420Conversion), HONDA CROSSCUB110(420Conversion), HONDA SUPER CUB110-PRO(FI Vehicles), HONDA SUPER CUB110PRO, HONDA SUPER CUB110(FI Vehicles), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110(420Conversion)

Japanese Webike user

3/5

Purchased to replace Driven Sprocket and Chain and 3 other items at the same time.

The standard 14T was replaced with a 15T and the Driven Sprocket was replaced with a 33.
As for Image, it looks like Drive was changed to 15.5 Ding.
The RPMs were lowered, so the fuel consumption was up 5 km.
The first gear can now be handled like a normal Motorcycle.
But as the Shop Owner said during installation.
OEM has anti-vibration Rubber, but this one does not.
He said that the running sound would change.
This is especially noticeable at low speeds. It is a clatter from toot-toot.
What do you want from a CUB?
This is what I felt most after the exchange.
Personally, I plan to return to the OEM standard 14T and 34-ding next time. View detail

KITACO

18 May 2023

Front Sprocket

Fits: HONDA NSF100, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA DAX125, HONDA MONKEY125, HONDA MONKEY125, HONDA MONKEY125, HONDA glom, HONDA glom, HONDA glom, HONDA CROSSCUB110(FI Vehicles), HONDA CROSSCUB110(420Conversion), HONDA CROSSCUB110(420Conversion), HONDA SUPER CUB110-PRO(FI Vehicles), HONDA SUPER CUB110PRO, HONDA SUPER CUB110(FI Vehicles), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110(420Conversion), HONDA SUPER CUB110, HONDA APE 100 TypeD

Japanese Webike user

3/5

I raised it from 12T to 13T and 13T to 14T.

I went from 12T to 13Th to lower the Engine RPM when driving. I went from 13T to 14T to lower the RPM a little more. Now I can cruise 60km before the engine roars even on a moped. Of course, it is only a moped when going uphill.
When I bought it, I noticed that the Washer shape is different between Takegawa and Tokico (the position of the Bolt hole and the notch to enter the Spline are reversed), so it cannot be fastened without using the Washer included in the package. View detail

KITACO

20 Nov 2022

Drive Sprocket (Front)

Japanese Webike user

3/5

Let's change it if we're going to Bore up! (^^ゞ

KITACO's have holes in them, so they're lightweight and provide heat protection! View detail

KITACO

05 Jul 2022

Super Drive Face Type X

Fits: YAMAHA CYGNUS X FI, YAMAHA CYGNUS X FI, YAMAHA CYGNUS X FI, YAMAHA CYGNUS X FI, YAMAHA CYGNUS X FI, YAMAHA CYGNUS X, YAMAHA BWS125(BWS), YAMAHA Axis Treat

Japanese Webike user

3/5

Lighter than NORMAL, but...

[How is it used?
I purchased this product to be installed at the same time as the High Prix.

Was the one you received as per Image?
It was just like the image.

Was the installation difficult?
Large may be odd because the drive system requires a special tool.

How was your experience with it?
I have been able to use it without any glitches, but I don't feel it is very effective.

[Included Parts:were they on?
There was nothing in particular

[Was there anything that disappointed you?
The fins are well made, but the large size of the fins is obviously smaller than the NORMAL fins.

▼ This is for installation at the same time as KITACO's Hi-Pre, and should not be installed as an OEM replacement. View detail

KITACO

14 May 2022

Front Sprocket

Japanese Webike user

3/5

Almost no change

[How is it used?
I purchased Sprocket to take it in the Short direction to compete in the CUB Race.
The OEM was 13, but we have changed it to 12, one notch lower.

How was your experience with it?
I didn't feel much of an effect, probably because the Engine was already done in the first place, and Time was almost the same.
About one gun on the Front side may not be nearly as effective for a 50cc CUB.

How did it compare to other products?
It was quite solidly made, with a meat-removal process and so on.

[Points to note]
Nothing in particular. Installation is not difficult.

Other items that would be helpful
Whether there are Included Parts:/ Items that should be purchased together/Opinions and requests to the Manufacturer
The number of Chain Piece could be handled without any change. View detail

KITACO

15 Aug 2021

Drive Sprocket (Front)

Fits: YAMAHA RZ50, YAMAHA YB-1 FOUR, YAMAHA TZM50, YAMAHA RZ50, YAMAHA MATE80, YAMAHA MATE80, YAMAHA MATE80, YAMAHA MATE80, YAMAHA MATE80, YAMAHA MATE80, YAMAHA MATE50, YAMAHA MATE50, YAMAHA MATE50, YAMAHA MATE50, YAMAHA MATE50, YAMAHA DT50, YAMAHA TT-R90

Japanese Webike user

3/5

I've just been proven wrong about the Net rumors.

I'm talking about Net's rumor Level. "I heard that the front sprocket of RZ50 fits CHOINORI. The inside diameter of Spline (16?) did not fit and I gave up to install. This size (17?) is the same as 80?Minimoto, Monkey, Cub and so on. I'll use it for Spare. View detail

KITACO

19 May 2021

Power Drive Kit Type 3

Fits: HONDA Byte, HONDA ZOOMER, HONDA CREA SCOOPY, HONDA CREA SCOOPY, HONDA SMART DIO, HONDA SMART DIO, HONDA SMART DIO, HONDA SMART DIO

NO NAME

3/5

One missing part was delivered

Hello, I received the product yesterday and checked it. As a result, it was delivered without pulley grease (5.0g) X1. It was delivered in good condition, but the pulley grease was missing in the photo. Please check it~ Good job ------------------------------------------------------- -------------- Hello, me check results hayeoseo yesterday received the goods, The pulley Greece (5.0g) X1 is shipped without. Shipping status, although preferably Shipping The photo shows Greek shipping pulleys were missing in the state. OK, thank you ~ work hard Powered by Google Translator View detail

KITACO

27 Apr 2021

Front Sprocket

Japanese Webike user

3/5

Trusted KITACO

Sprocket is available from many companies.
I bought Mr. KITACO from MAJOR place.
I think Sprocket is the Manufacturer of choice. View detail

KITACO

21 Mar 2021

Rear Sprocket

Fits: HONDA SUPER CUB 50, HONDA SUPER CUB110, HONDA SUPER CUB110, HONDA SUPER CUB110-PRO, HONDA CROSSCUB110, HONDA CROSSCUB110, HONDA MONKEY125, HONDA DAX125, HONDA glom, HONDA SUPER CUBC125, HONDA SUPER CUBC125, HONDA SUPER CUB 50-PRO

Japanese Webike user

3/5

jc92 grom needs large size screw hole.

[How is it used?
Cannot be pimped.
Was the one you received as per Image?
Street Image
Was the installation difficult?
Screw holes need to be machined to increase the size of the SprocketBolt on the Type 3 Grom.
How was your experience with it?
I changed my mind. Looks better than NORMAL!
[Included Parts:were they on?
None
[Was there anything that disappointed you?
None
Other items that would be helpful
I can't wait to get one for the Type 3 jc92 Grom. View detail

KITACO

07 Mar 2021

Power Drive Kit Type X

Fits: YAMAHA CYGNUS X FI, YAMAHA CYGNUS X FI, YAMAHA CYGNUS X FI, YAMAHA CYGNUS X FI, YAMAHA CYGNUS X FI, YAMAHA CYGNUS X, YAMAHA Axis Treat, YAMAHA BWS125(BWS)

Japanese Webike user

3/5

be unsteady

I changed a lot of things together, so I didn't really understand the effect.
Why does the Pulley rattle? It's like that.
Did they fail to install it?
At any rate, there is no problem in the test run, but the Idling sound became noisy. View detail