Reviews
Rectification Diode changed (Repost)
20240312Review
Initially, the selection of Diode was based on the wisdom of our predecessors (1N4148 100V200mA) But it broke, so I replaced it with an Emon one. I was worried because I needed 700mA for the NORMAL bulb and 900mA for the replaced bulb, but it was still no good. It was easy to work with. The diode itself is large and sturdy even with a weaker one.
↓ The following Review is a Diode change from the last one I posted.
good point
It seems to be small and unbreakable.
Maintenance is also easy, since the corresponding Valve can be purchased at Home center. (W number confirmation required)
A bad point
Single Bulb, so depending on the year, position modification may be required.
Bullet Terminal has Female and Male, so Large Mortgage Wiring needs to be processed.
Blinker relay in md44 must be replaced
Parts used
12 v10w13tValve×4
POSH Blinker Conversion Coupler Code Hondafor Front (18-19CB1300SF/SF-SP) ×Quantity:1pc.
・Emon (amon) Rectification Diode 6A Quantity:2pc. Set in 1556 ×2Pack (4 pieces in total)
Sumitomo Wiring Systems, Ltd. 050-type HCSeries2-poleFConnector2P050-HC-OR-F-tr ×Quantity:1pc.
Sumitomo Wiring Systems, Ltd. 050-type HCSeries2-poleFConnector2P050-HC-SB-F-tr ×Quantity:1pc.
Sumitomo Wiring Systems, Ltd. 050 type 1 pole F-side Connector1P050-WH-F-tr ×2co.
POSH) Motorcycle accessories Wide watt blinker relay (LED compatible) 3-wire Type 090011-WR ×Quantity:1pc.
Nut or Bolt, RubberWasheretc., number required
The included Valve is 12v8w10t and a little dark, so I changed it to 12v10w13t. The Valve generates a lot of heat, so I think you should inspect it carefully.
Front Blinker's Connector is "Made in USA" and I couldn't get it from Wiring.com.
For position processing, a rectifying diode is inserted in the position line and the turn signal line to prevent reverse current flow. If this is not done, the Indicator will remain on all the time.
I bought all the connectors for the rear blinker from Wiring.com. plus side connectors are in KITACO's ConvenienceParts, but minus side is not available.
The Rear bracket is a Fender Eliminator Kit from DRC, and the Front bracket is an appropriate Bracket that I found at Home center. I was surprised to find that it hooked up EXACTLY.
Blinker relay must be replaced. rally's blinker relay is for LED, but there is information that DRC's LEDFlasher is high flasher, so I thought I could use unbreakable lens with low w number, but it was not possible. I bought a used OEMRelay for md38 and it is a high flasher. It is better to buy ICRelay.
Posh's Blinker relay has a waterproof body, but the connector is exposed and needs to be treated. I wrapped it with tape from Vinyl housefor Repair.
View detail
Off-road standard
good point
It seems to be small and unbreakable.
Maintenance is also easy, since the corresponding Valve can be purchased at Home center. (W number confirmation required)
A bad point
Single Bulb, so depending on the year, position modification may be required.
Bullet Terminal has Female and Male, so Large Mortgage Wiring needs to be processed.
Blinker relay in md44 must be replaced
Parts used
12 v10w13tValve×4
POSH Blinker Conversion Coupler Code Hondafor Front (18-19CB1300SF/SF-SP) ×Quantity:1pc.
UniversalSmall Signal High Speed Switching/Diode 1N4148 100V200mA ×4Co
Sumitomo Wiring Systems, Ltd. 050-type HCSeries2-poleFConnector2P050-HC-OR-F-tr ×Quantity:1pc.
Sumitomo Wiring Systems, Ltd. 050-type HCSeries2-poleFConnector2P050-HC-SB-F-tr ×Quantity:1pc.
Sumitomo Wiring Systems, Ltd. 050 type 1 pole F-side Connector1P050-WH-F-tr ×2co.
POSH) Motorcycle accessories Wide watt blinker relay (LED compatible) 3-wire Type 090011-WR ×Quantity:1pc.
Nut or Bolt, RubberWasheretc., number required
The included Valve is 12v8w10t and a little dark, so I changed it to 12v10w13t. The Valve generates a lot of heat, so I think you should inspect it carefully.
Front Blinker's Connector is "Made in USA" and I couldn't get it from Wiring.com.
For position processing, a rectifying diode is inserted in the position line and the turn signal line to prevent reverse current flow. If this is not done, the Indicator will remain on all the time.
I bought all the connectors for the rear blinker from Wiring.com. plus side connectors are in KITACO's ConvenienceParts, but minus side is not available.
The Rear bracket is a Fender Eliminator Kit from DRC, and the Front bracket is an appropriate Bracket that I found at Home center. I was surprised to find that it hooked up EXACTLY.
Blinker relay must be replaced. rally's blinker relay is for LED, but there is information that DRC's LEDFlasher is high flasher, so I thought I could use unbreakable lens with low w number, but it was not possible. I bought a used OEMRelay for md38 and it is a high flasher. It is better to buy ICRelay.
Posh's Blinker relay has a waterproof body, but the connector is exposed and needs to be treated. I wrapped it with tape from Vinyl housefor Repair.
View detail
Right size
Found this fog light attractive and the size is just nice to fix it on my MT09. It would be great if it's come with dual colour. Quality is excellent. View detail
Couplet-on and easy!
It is often said that the Light of CT110 HUNTER CUB is dark, but it is really dark.
When you enter a dark Tunnel from a bright place, such as an old Tunnel at night or even during the day, you can't see anything.
So, after considering the introduction of KITACOLED Shuttle Beam with Mukawa and KITACO's auxiliary light, they purchased KITACOLED Shuttle Beam.
Installation is completed by connecting the Connector such as Couplet-on and Switch to Headlight's Attachment power supply.
If anything, it took a little more time to remove the Headlight Connector and the power supply coupler.
I turned on the auxiliary light installed in the nighttime test,
Satisfied with the brightness of the front and both SIDE of the car body hand of the Normal headlight.
I am not sure about the durability as I am just starting out, but I am a little concerned about wet weather and washing the car as it was not marked as Completely Waterproof.
、
View detail
Transplant to XG250 TRICKER
Mounting bolts, wiring extension, mounting bracket, etc. were modified and ported to XG250 TRICKER.
The difference in valve resistance made it a high flasher, but the Small blinker made it Stylish.
View detail
CT125 Auxiliary Lamp
Finally installed the auxiliary Lamp.
CT125CT110 HUNTER CUB Light is dark ...
If possible, it would be nice if there was a standard product that would allow the LEDs inside to be replaced,
If the entire reflector and headlight unit are replaced in accordance with the H4 standard, the cost of the gold is not unreasonable.
So there is Kit from Mukawa and KITACO, which has a proven track record in auxiliary Lamps from various companies,
Decided to go with the less expensive KITACO product.
If you install USB power supply and Auxiliary Light together in Attachment power supply, the voltage capacity will be Over.
Remove the USB power supplyConnector that has been attached.
About, SmallInstalled in about an hourCouplet-on and easy to work with.
Installation is completed in Large form.
All installation is completed when the irradiation test and angle adjustment is done at night.
As for durability, we will see.
View detail
For Custom
I bought this for Custom for Grom.
I thought about LEDs, but Wiring and other
I thought about the hassle w this one for the time being.
I am satisfied with the product.
This time, we purchased the front and back together.
View detail
COSPA is good.
As with the Front, I was disappointed that the included Orange-colored bulbs were transparent, so I painted them Silver and installed them myself. There are products from other manufacturers that come with bulbs painted silver, but KITACO's products are very kind in terms of price. View detail
MONKEY125 pica.
The power supply is taken out from the front brake switch, and the power supply for the motorcycle I used to ride is the same as that of the front brake switch.
I used KITACO's headlight switch and installed it on the front fork with a band.
View detail
Body tightening!
It is good for tightening the body line. However [Color] The Smoke color was a little darker than I expected, I would have liked it better if it had been a middle ground between the Clear color and the Smoke color. I had no problem at all with the quality and installation. View detail
Fits: HONDA JADE, HONDA GYROUP, HONDA GYROX, HONDA TOPIC, HONDA TOPIC, HONDA TOPIC, HONDA NS-1, HONDA JADE
90's Scribner's Tail
The Tail lamp was cracked and missing, so I converted it to a clear tail at this time.It contains a Clear Lens, a red painted bulb and a reflector. I had to shave off a little too much of the red from the License Plate Light when I installed the bulb, but I did…The Tail lamp itself is great because it glows a pale pink. I can see a bit of the bulb color at the bottom…It goes well with the Silver car body! View detail
Wiring
Since it is a KITACO product, it is well made, and I think the quality is consistent. Unfortunately, the wiring is only 30CM, so when connected to the front fork, the wiring connected to the Bullet Terminal cannot be hidden under the tank, so the front fork has to be used as a weather suit for the wiring. It is a pity that the eyes are exposed to rain. View detail
Fits: SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125
It is satisfied. A color will merely be reflected in case of an attached red electric lamp. However, legally, since the electric lamp must be made into red, it is a recommend which is changed into LED etc.
It is satisfied.
A color will merely be reflected in case of an attached red electric lamp.
However, legally, since the electric lamp must be made into red, it is a recommend which is changed into LED etc.
View detail
For Dress-up
Installed on a 14 grom, very easy to install, just remove one screw and replace. It looks much tighter and more parenthesis. View detail
I was concerned about visibility, but it looks fine.
OEM Replacement Type
more than I thought [Color] I was worried about visibility because Smoke was dark, but it looks fine.
View detail
Parenthesis is good in Plating style!
[How is it used?
I was looking for a Bracket to attach the Blinker to the Front fork in a Classic Plating style, and I found it at a reasonable price!
Was the one you received as per Image?
Parenthesis is as good as Image!
Was the installation difficult?
It is easy with a split system.
How was your experience with it?
Steel, but the thickness is so thin that distortion will occur.
[Included Parts:were they on?
Bracket and Screw only
[Was there anything that disappointed you?
Not particularly
Please note that the front fork is not NORMAL.
View detail
I'm not sure the fit is good enough.
Tail. [Color] Ordered this to create a unified look since I switched to Smoke LEDs.
The look of the Rear is tightened ………, but the Right Side is not hooked tightly enough, probably due to the accuracy of the Screw Mount.
It makes a crackling sound when lightly tugged. (Lol) 。
New Rubber packing and Screw but no effect.
I have had no choice but to reorder the same product and hope that it will get hooked up properly.
View detail
light
The Blinker is a classic, but this was my first time using it.
It is smaller than the OEM's typical blinker and gives a SMART impression.
Small Type is lightweight and has little protrusion from the body, so it will not be glued to the ground even if the Front is tipped over.
It would have been better if there was a Bullet Terminal product for the Rear for use with other vehicles.
View detail
Does it make you look better?
It's a pimped out version of the NORMAL Lens and just changes the sphere.
The Lens. [Color] Smoke and Matte Black of the body color.
Match.
View detail
Since the OEMBlinker has been smashed.
After driving on the forest road, I found that the rear blinker was missing, I ordered the OEM product and put it on, but it was gone soon. I decided to replace it with an Unbreakable lens. I changed the mounting position to License PlateCarrier Top, and removed License PlateCarrierBottom.
If the front blinker is also broken, I will replace the unbreakable lens.
View detail