Reviews
Good manufacturing, as good as OEM.
It can be tightened with confidence.
It is well made, so let's tighten it up with a proper Band.
View detail
I put it on as a spare.
External Fuel filter attached to ESTRELLA.
It has been immobile for a while, and you can often find a little bit of age-related deterioration in various parts of the car. 。
There does not appear to be any fuel seepage, especially in the Fuel Cock area, but there is no denying that the Fuel Cock has deteriorated over time.
The other day, I was worried about the rust in the fuel tank, and although I have removed rust to prevent impurities from entering Gasoline, I am not sure about it, so I will install an additional external type of fuel filter.
Fuel filter
A filter device used in automobiles to filter fine impurities contained in fuel.
It is used for the purpose of removing water, sand, and dust mixed in during refueling, etc., and maintaining sufficient fuel efficiency.
There seems to be a time for replacement, though not up to the air filter.
■ 50,000 km at Carburetor Vehicles
■Injection car with 100,000 km
■Diesel car with 50,000 km
is the standard.
Continued use of the filter past its replacement time will not only clog the fuel filter element and cause a lack of engine output, but will also cause the filter to lose its original function of capturing foreign matter and separating moisture.
[When the fuel filter clogs.
‥
Idling of ▲Engine is unstable.
Engine seems to stop when driving.
▲ Suddenly, Engine stopped spewing.
Failure to start = Engine will not start.
I haven't experienced the clogging of the Filter yet, but considering the distance and age, it should be replaced. 。
In my 90's ESTRELLA, the fuel filter is integrated with the fuel cock and inserted into the tank. That is not so bad, but I wanted to be sure.
I also added an external Type as a spare.
I chose KIJIMA's because it was inexpensive and I had used it before.
The deciding factor was the transparency, which makes it easy to see dirt.
Replacement procedure.
(1) Fuel Cock is turned off
↓
(2) To be sure, Gasoline in the carburetor should also be removed.
↓
(3) Interrupt the fuel filter between the rubber hose connecting the fuel cock and the carburetor.
It is wise to prepare Oil Resistant Hose separately because OEM Hose is not long enough.
↓
(4) Turn on Cook and apply Engine.
Operation check.
Fuel Cock flows by Engine pressure.
after replacement
No problems
They seem to be getting rid of the impurities for sure.
Durability...? I think Large is durable because it is inexpensive and will be replaced with a con stunt.
It is a good idea to have insurance on older Motorcycles.
Installation is also easy.
View detail
Fits: BMW R1200GS, BMW R1200GS Adventure, BMW R1200R, BMW R1200RS, BMW R1200RT, BMW R1250GS, BMW R1250GS Adventure, BMW R1250R, BMW R1250RS, BMW R1250RT
It's a must for Oil replacement.
BMW is said to be a Motorcycle only for the rich, but I still want to put in my favorite Oil and keep the cost down.
The only thing I decided to ask Dealer for was the price, and the price is meta-fucking-high.
So I changed the Oil by myself!
Attachment, too!
This is essential in that case!
View detail
Fits: KAWASAKI Ninja 250, KAWASAKI Ninja 400 (2014-)
Cospa strongest
OEMRear Fender was so creepy that I decided to convert it to a Fender Eliminator, because the Kit is cheap, the License Plate looks like it grows directly from the Motorcycle, and there is a Loading Hook. (In Z400, removing the OEMRear Fender means losing the Loading Hook.) The fact that you can use an OEMBlinker is also Gold-friendly.
KIJIMA's description claims that it is for NINJA400 and NINJA2 Helmet50R, and does not mention a single word about my beloved Z400, but this Quantity:I bought this one because I saw some guys on the Internet who installed Set on their Z400, and the back of Z400 is almost the same as the current NINJA400.
The Kit itself is carefully processed and absorbent to the touch. I thought I got my money's worth at this stage. The installation instruction manual is also very detailed and easy to understand. The hardest part of the installation was the removal and installation of the blinker and the coupler of the license lamp, and the porting of the OEMB blinker. I cut off the rubber cover around the Coupler and solved the Blinker by my own efforts. All of them are Kawasaki's fault, not KIJIMA's. Kawasaki designed the blinker with poor maintainability. What is going on with Kawasaki?
The Loading Hook is also very useful and in a very good position. It is a great product that makes me feel like a fool to buy a kit around 20,000 yen for the same purpose when such a great kit is available.
View detail
Surely this is useful.
However, the helmet lock of CRF250L I bought this year is located near the rear fender, and it is indeed difficult to hook the helmet, so when I used this KIJIMA's Helmet lockAssist, I found it very easy to use. It became easy to use at a stretch when I used this KIJIMA Helmet lockAssist.
I usually leave it attached to the helmet lock and hook it up, and remove it when I use the helmet lock.
It is a very simple Ideas product, as all you have to do is pass these Parts through the DRing and hook it to the Helmet lock, but it is certainly useful.
It depends on the position of the helmet lock, but if the position of the helmet lock is not quite right and it is difficult to use, this is a convenient product that I recommend.
View detail
Fits: SUZUKI GIXXERSF 250, SUZUKI GIXXER 250, SUZUKI GIXXER150, SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI BURGMAN 400
You should change the cheap ones often.
This is a reasonably priced Filter for a 2012 KTM DUKE200. If you are a normal rider, it is better to change the cheap one frequently than to buy an expensive Filter and use it persistently.ОRing should be changed once in a while, and at that time you should use Quantity:Buy Set's stuff!
Motorcycles that have been run a lot do not have gold dust, so it is enough without magnet.
The replacement procedure assumes that the Oil is drained.
Remove the lid of ?Filter. 8mmWrench
?This time we will use the lid side and the back ОRing.
Remove the filter and tighten the Bolt on the lid to finish. After replacing the filter, run it for a while to check for leaks.
By the way, the cheap ones seem to have large filter holes. The cheap ones may have oil leaking out from the gap, not into the filter but into the inside of the filter.
View detail
Exactly to the OVER baxter!
Rubber Only replacement is available at a lower price than OVER's Kit. View detail
Fit and perfect
I installed it on the Yamaha Tracer 900 GT, one on each side. The position is accurate and firm. It is convenient for parking and placing the helmet. It is securely locked. The price is cheap and it is worth installing. A good experience. The logistics is fast. Recommend you to buy this item------------------------------------------------ ---------- I installed it on the Yamaha Tracer 900 GT, one on each side. The position is accurate and firm. It is convenient for parking and placing the helmet. It is securely locked. The price is cheap and it is worth installing. A good experience. The logistics is fast. Recommend you to buy this item Powered by Google Translator View detail
Good visibility
It is easy to see and use even during the day. It is also good that USB can be used for power supply. View detail
Fits: HARLEY-DAVIDSON Universal
Used to secure Tool Bag
If you use it with a Carrier, you need to be creative when installing it because it interferes with the Carrier's legs. View detail
Fits: HUSQVARNA SVARTPILEN 401, HUSQVARNA VITPILEN 401, HUSQVARNA SVARTPILEN 200, HUSQVARNA SVARTPILEN 125, HUSQVARNA SVARTPILEN 250
The best choice for waterproof bag storage
It was useful during long distance tours.
Since the rear seat of the Svartpilen is short and narrow, this carrier can stably hold a waterproof bag of about 40 liters.
The design is simple, so it doesn't look too distracting.
Both 1st and 2nd generation fillens can be used. -------------------------------------------------- -------- It was useful during long distance tours. Since the rear seat of the Svartpilen is short and narrow, this carrier can stably hold a waterproof bag of about 40 liters. The design is simple, so it doesn't look too distracting. Both 1st and 2nd generation fillens can be used. Powered by Google Translator
View detail
tw200
The appearance has been improved by the Large change,
The instruction manual was easy to understand and I had no trouble installing it.
View detail
Insistence is strong
The bar is quite high and has a strong presence.
The color and texture are nice.
View detail
a perfect fit for a bike
very precise and sparkly It's easy to wear It would be nice if the prescribed torque value for the fastening bolt was written. The combination with "overracing subframe" is good My bike has become a little more shiny. View detail
Repair of external Exhaust System.
The Band of Earls Gear's Slip-on Silencer that I bought used is not usable because the Screw does not turn in RustRust.
I checked and it was the same as this product.
The band itself is stainless steel, and the screws are iron, so Copa Coat is applied to the screw threads to prevent biting and rust.
It can be tightened normally and looks normal. No exhaust leaks, probably because it is evenly tightened.
I thought it was a good, safe product.
View detail
Good
If you read the manual, it is easy to install and fits well. It weighs more than you think. The cooling fins have a nice shape. View detail
inconspicuous
I was a bit surprised at the price for such a bracket, but considering the time and effort required to find a substitute and the fit, it may be inexpensive.
The method of installation is up to you.
View detail
It can also be used on the lower road!
I bought it on impulse, thinking that it would be good if I could use it mainly on downhill roads. Surprisingly, my right hand became very comfortable. I have heard some people say that they can't use it because it slides too much, since the grip varies depending on the large size and texture. In my case, it was just right. So, if you feel it is going down, you can easily put it back up. It almost never comes down, though. This is a great buy! I wish I had tried it sooner! View detail
Reliable Engine Guard
I bought this because I was worried that the side pipe on my NC750X alone would interfere with the side pipe when it tipped over. I was told that it would interfere with the side pipe and that it was Large sturdy, but it did interfere with the side pipe. I had to cut it with a sander and paint the cut surface matte, but I was satisfied with the finished product.
Sparks and noise are great when cutting, so be careful if you try it.
View detail
Fits: HARLEY-DAVIDSON FXLRS SOFTAIL LOW RIDER S, HARLEY-DAVIDSON FXLRST SOFTAIL LOW RIDER ST, HARLEY-DAVIDSON FXRST SOFTAIL LOW RIDER EL DIABLO
Pull back easily
It is just right to be able to pull back easily without changing wiring.
If this isn't enough, you could replace the Riser and raise it.
It's cheap and helpful.
View detail