Reviews
Although the shape is different from those made by Ekimon, Yaoki, and others.
The Crimp section has not been modified in any way, such as being slightly folded from the beginning, so it is a little troublesome to Crimp with Electric Works Pliers, but it is good for Crimping several thick or thin Cables at once.
In addition, the sleeves for waterproof and insulation are a little thicker than those of the Title companies, but there were no particular problems when they were mixed with those made by those companies.
View detail
Kiboshi Terminal Set
Quality and Texture Information Typical Jiboshi Terminal Set Full of Male Terminal for usability Product Inquiry Crimper To Buy With, Female Terminal Easy to install Cost performance and comparison sets with other products are affordable WeBike packaging is always great. Arrives in a week for delivery and packaging I ordered it after looking at the word "set" to see if the translation was wrong when I bought it, but only the Male Terminal came and checked the site again, and the notice came up that there were 8 Male Terminals. I need to order again because it's internalism. It goes well with Honda View detail
For branching
This is for use as a branch of a power supply.
110" 2PConnector, Pin Quantity:Set, but it would have been enough if we could have connected with other cheaper ones.
View detail
I would love to see it sold in rolls.
Installed on a GSX-R1000R 2019
Used as Wiring protection for retrofitted electrical components.
Generally, PVCTube is used, but it needs to be threaded before attaching the coupler, and if the wire is long, threading it is also a tedious process.
Furthermore, once installed, it is time-consuming to branch out in the middle.
There are also options such as Colgate Tube and Spiral Tube for wiring that has already been installed, such as Coupler,
Colgate Tube is not very good looking and is not flexible, and Colgate Tube is too stiff to begin with, and may give Damage to Wiring. (especially at both ends)
Spiral Tube is not very good looking, very troublesome to install, and has many gaps, so its protection performance is not very good.
and none of them were willing to actively use it.
That is where this product comes in.
This product is similar to the Colgate Tube in that it is a rounded Habit-attached Sleeve that wraps around the Wiring, so it is easy to put on and take off.
However, this product is different from Colgate Tube,
Cloth-like appearance and high texture
OEMHarness-like atmosphere and not too conspicuous
Flexible and Flexible
Not hard, so it is friendly to Wiring
and Merit everywhere.
It is the best, to say the least.
I am even wondering if I should buy it in Large quantity and Wrapping all the retrofit Harnesses with it.
NegativePoint is ….
If I had to say, it would be the selling method.
Since it is only sold in 1m lengths, it is relatively expensive and not available in lengths longer than 1m.
Also, although there are few situations in which more than 1 m of 1 pc material is needed, it is rare for 1 m to be used up in a good Drill, so a few cm of the SIDE will be Garbage every time.
I would like to see these products sold in rolls of 5m or 10m units.
It is also more eco-friendly, as no scraps are produced.
Anyway, I couldn't be more satisfied with the thing.
Personally, this is my best buy of the year.
We hope Manufacturer will consider selling the product in rolls.
View detail
CRF250L MD47 for ACCWiring extraction
Used on a 2023 CRF250L.
If you remove the Left Side Cover, you can access the upper area of the Accessory Case, where there is a 4-pin Optional Connector hidden by the Waterproof Cover. There is a 4P Optional connector hidden by the waterproof cover.:Since 2pc is ACC, we used this Connector to take out ACC and used it for ACC connection of DAYTONAD-UNIT.
View detail
This is a summary purpose of the branched Wiring.
[How is it used?
To consolidate additional and branched wiring in the front cowl of ADV160.
Was the one you received as per Image?
The size and texture were exactly as shown in the Image.
Was the installation difficult?
Simply remove part of the Cowl and reinsert the Wiring.
How was your experience with it?
It is nicely put together, and since it will also be Cover, we can expect Simple Waterproof.
View detail
Easy to use
Used for Wiring protection around Engine.
The Protective Tube is easy to install and looks like a tube, whereas a normal Protective Tube requires the Connector to be removed.
It would be even better to have Variation such as White color.
I gave it a 4 because it has just been installed, but I don't think there are any problems with its effectiveness.
View detail
It can be used normally
It was rather expensive, but I needed it, so I bought it. View detail
KIJIMA KIJIMA Self-wrap Sleeve
[How is it used?
Dress-up Wiring in Quick shifter.
Was the one you received as per Image?
As per Image
Was the installation difficult?
It is easy just to wrap it around. Can be cut with Scissors to any desired length.
How was your experience with it?
It was a bit Race ish.
[Included Parts:were they on?
nothing special
[Was there anything that disappointed you?
nothing special
View detail
KIJIMA KIJIMA Self-wrap Sleeve
The coupler can be wrapped directly around the wiring for easy installation without the need to cut the wiring or remove the coupler.
It is available in several thicknesses, making it ideal for dress-up.
View detail
It's a safe and reliable product.
I purchased this product because I needed it to get an earth reading for the installation of a DriveRecorder in my car.
The product is an ordinary Stag beetle terminal, but it is solid and not unreliable with PelePera. It is a safe and reliable product.
This time, I combined this terminal with a 0.75 cord to make Minus Wiring. I am planning to redo the wiring for Motorcycle's DriveRecorder- etc. in the near future, so I would like to use the rest of this time for Motorcycle.
Well, it is one of those things that you want to Stock because you will often need it.
View detail
Wiring Protection
Used to wrap Wiring, easy to roll, soft, elastic and good looking, but a little expensive. View detail
that's all right
Used with EngineWiring protection. It looks better than the Sbiral Tube. I think it is good for engine wiring protection, especially for LargeEngine Displacement Volume Motorcycle with high engine heat. Cost is high and it is difficult to install. View detail
For rainy day measures.
I bought this Coupler because the original Coupler was not waterproof specification. It's a bit large, but I think it's safe for rainy days...? View detail
Looking forward to the performance…
I used it through the Controller's Wiring of Sub computer.
I used it for the USB cord to connect to my PC for setting, but I was worried about the heat because I had to put it along the frame.
I did the construction with this Self-wrap Sleeve expecting the flame resistance and the heat resistance. So far, the problem has not occurred, so I guess we'll see.
View detail
Ideal for securing the Earth of the device to the Bolt of the vehicle.
I use it to hold the Earth of the electronics firmly in place through the Bolt on the car body.
The Stag beetle type would have been fine, but it would have fallen off while removing the Bolt. This perfectly round product is attached to the Bolt properly, so there is no need to worry.
Just be careful because you need to remove the Bolt completely.
Also the Sleeve is properly Quantity:It is safe because it is Set.
View detail
The size is a little large, but the practicality is perfect.
[How is it used?
ai-net i-Net Waterproof Mini Flat Type Fuse Holder MINI Flat Type is used to protect PL Insurance Products outside the car. The Fuse holder itself is waterproof, but in order to increase the degree of waterproofing, this Wiring Cover is also used together.
Was the one you received as per Image?
It's a little bigger than I thought it would be.
Was the installation difficult?
It's not difficult at all because it's just threading a cable, but it was difficult to find a place to place it because the body is large.
How was your experience with it?
I wrapped it with WaterproofTape because rain enters from the part where I pass the cable.
View detail
Convenient!
I didn't know there was such a thing! I was surprised and bought it.
I used it in a place where I could connect it with Bullet Terminal, but it would be lumpy and I wanted to put it together in SMART.
You need to melt the solder, so you need to put heat into it.
View detail
Nice finish.
It is a ready-made branch Bullet TerminalWiring.
It's well made and won't get shredded or weird.
It saves valuable time and is cheaper than having the materials available for local use.
View detail
Sufficient performance
Accuracy is good, and the Bullet Terminal snaps into place in a small, spontaneous way.
The Rubber seal is of good quality and still holds up well about two years after installation.
If I ever get the chance to use it again, I will choose this one.
View detail