Reviews
I put it on as a spare.
External Fuel filter attached to ESTRELLA.
It has been immobile for a while, and you can often find a little bit of age-related deterioration in various parts of the car. 。
There does not appear to be any fuel seepage, especially in the Fuel Cock area, but there is no denying that the Fuel Cock has deteriorated over time.
The other day, I was worried about the rust in the fuel tank, and although I have removed rust to prevent impurities from entering Gasoline, I am not sure about it, so I will install an additional external type of fuel filter.
Fuel filter
A filter device used in automobiles to filter fine impurities contained in fuel.
It is used for the purpose of removing water, sand, and dust mixed in during refueling, etc., and maintaining sufficient fuel efficiency.
There seems to be a time for replacement, though not up to the air filter.
■ 50,000 km at Carburetor Vehicles
■Injection car with 100,000 km
■Diesel car with 50,000 km
is the standard.
Continued use of the filter past its replacement time will not only clog the fuel filter element and cause a lack of engine output, but will also cause the filter to lose its original function of capturing foreign matter and separating moisture.
[When the fuel filter clogs.
‥
Idling of ▲Engine is unstable.
Engine seems to stop when driving.
▲ Suddenly, Engine stopped spewing.
Failure to start = Engine will not start.
I haven't experienced the clogging of the Filter yet, but considering the distance and age, it should be replaced. 。
In my 90's ESTRELLA, the fuel filter is integrated with the fuel cock and inserted into the tank. That is not so bad, but I wanted to be sure.
I also added an external Type as a spare.
I chose KIJIMA's because it was inexpensive and I had used it before.
The deciding factor was the transparency, which makes it easy to see dirt.
Replacement procedure.
(1) Fuel Cock is turned off
↓
(2) To be sure, Gasoline in the carburetor should also be removed.
↓
(3) Interrupt the fuel filter between the rubber hose connecting the fuel cock and the carburetor.
It is wise to prepare Oil Resistant Hose separately because OEM Hose is not long enough.
↓
(4) Turn on Cook and apply Engine.
Operation check.
Fuel Cock flows by Engine pressure.
after replacement
No problems
They seem to be getting rid of the impurities for sure.
Durability...? I think Large is durable because it is inexpensive and will be replaced with a con stunt.
It is a good idea to have insurance on older Motorcycles.
Installation is also easy.
View detail
tw200
The appearance has been improved by the Large change,
The instruction manual was easy to understand and I had no trouble installing it.
View detail
Rubber hose is consumable!
[How is it used?
Used for SUZUKI/CHOINORI Fuel Hose and Negative Pressure Hose.
I purchased this product to replace the hose that had been attached to my car because it had deteriorated over time.
How was your experience with it?
It is brand new Rubber so it is very soft.
Does this make it easier to get the fuel down? I think it has become easier.
How did it compare to other products?
We selected KIJIMA because it was the one with the lowest gold price, although other manufacturers also offer similar products.
I am glad to hear that it is working fine.
[Points to note]
You will be handling Gasoline, so be careful not to ignite it.
View detail
No wasting Gasoline
The Breather Hose 650mm 6mm Diameter on the tank cap of the KLX230R does not have a valve, so when it falls over, gasoline leaks out. However, I wanted to prevent leakage by attaching a valve to the tank cap to prevent physical exertion if I rushed to wake the tank cap up. Actually, I bought a Short Type with a Valve on the tip of the Hose before this one, but when I fell down, Gasoline dripped out of it. It is a pity that I cannot match the color with Kawasaki. View detail
Particularly good for places where there is a lot of ROSS
Reusable Tie Wrap for easy removal.
It is especially effective for parts that are frequently removed and attached. It is a little thicker than regular tie wrap, so be careful, but I use it to tie parts that are often removed when disassembling.
Off-road motorcycles are especially used for this purpose.
The thicker the wire, the sturdier it is, so there is no need to worry too much. However, if you cut the extra length, you can only use the same length or a shorter portion.
View detail
The ability to release as intended is still an advantage.
Vehicles used in Races and competitions are often cleared.
If Tie Wrap can be Released in such cases, it can be used once more.
This is important.
But it's not cosmetic. Definitely.
But they are SDGs. Because they can be reused.
Even if you are not a "good" person, you don't have to use a nipper to cut it, so you don't have to choose a place for it. It is surprisingly possible even in a gap where tools cannot fit.
View detail
Used to supply Gasoline as a startup check
Installed between the connection from a simple Gasoline container to Carburetor to prevent CarburetorOverflow.
Effective without CarburetorOverflow after adding Filter.
View detail
Fits: YAMAHA SR400, YAMAHA Cerro 250, YAMAHA TW200, YAMAHA TW225E, YAMAHA SR400, YAMAHA Cerro 250, YAMAHA TW200, YAMAHA TW225E
Cost and Performance
Power Filter, the standard Tune for intake and exhaust, Powerful.
The Power Filter makes the air flow smoother and provides air without stress to the throttle work, making the engine more responsive and increasing torque and power.
Throttle response when opening the axel has also been improved, and you will be surprised at the difference in the comfortable start.
Setting the carburetor and injector is essential for installation. After the carburetor and injector are installed, the power of the carburetor and injector can be experienced, but there are also Merit and Demerit.
Merit to be replaced by Power Filter
[Merit1] Power up The shorter the intake pipe is and the rougher the filter is, the more air resistance can be reduced by replacing it with an air cleaner. 。 Most OEM filters that use filter paper, etc., have low airflow per area and large intake resistance, whereas the mesh Power Filter has much lower intake resistance. 。 When the intake resistance is reduced, the negative pressure resistance when the piston is lowered during the engine intake process is also reduced, so both power and response can be increased. 。 The higher the RPM, the more air intake per hour, the larger the benefit will be, and as long as the fuel condition is well controlled, the power can be increased by replacing the power filter. 。
[Merit2 Sound change The Merit of replacing with the Power Filter is that the intake sound becomes easier to hear. 。 Normal air cleaner box is designed to reduce intake noise, so intake noise is barely audible 。 The bare power filter directly emits the sound of the engine intake, and this alone creates a sporty atmosphere. 。
[Merit3 Space-saving By eliminating the air cleaner box, which occupies a large volume of space in the motorcycle, the available space can be effectively utilized. In addition, it contributes to weight reduction. 。 Mopeds with less loading Space can increase their loading capacity, albeit slightly, by installing an Accessory Case! 。
It seems to be a Power Filter full of good things, but there is also this Demerit.
Power Filter Demerit
[Demerit1] When replacing the noisy Power Filter, not only the intake sound but also the blasting sound of the Engine and even the Mechanical Noise can be heard.
The air cleaner also serves as a silencer, and replacing it with a power filter will significantly reduce the silencing performance of the intake system, etc., so when the RPM is increased, the noise may be greater than the exhaust noise. 。 I like it (laughs).
[Demerit2] Low-speed Torque becomes thinner and harder to ride. 。 The Power Filter and direct carburetor certainly increase power by reducing intake resistance, but precisely this is only the result of the TorqueBand shifting to a higher RPM side. Therefore, the starting acceleration may seem weak, or the TorqueBand may lack the feeling of Torque when the Throttle is slightly opened, and the motorcycle may become difficult to handle.
[Demerit3] If the Power Filter has a nipple to install the blowby hose, there is no problem if the hose can be inserted there. However, it is illegal to release the blowby gas discharged from the engine to the large airflow because there is no installation point for a blowby hose. 。 Blowby gas is sucked out by the negative pressure of the intake air and is discharged because the replacement of the Power Filter or opening of the large air intake does not provide enough negative pressure as the OEMAir cleaner box does, and blowby gas cannot be sucked out as efficiently, The increase in the internal pressure of the engine crankcase prevents the piston from moving, resulting in power loss. 。 While replacing with a power filter will increase power by reducing intake resistance, it may also cause power loss by reducing blowby gas discharge efficiency.
Based on Merit and Demerit, I purchased KIJIMA's Power Filter this time, and it is not bad relatively speaking. In a word... it runs well (with Carburetor setting).
good point
◎Filter capacity, well treated joints, and durable performance.
◎Cheaper than K&N.
After Fire will not appear.
A bad point
◎ Cannot be used on rainy days. →Because it absorbs water.
◎Intake noise became annoying.
◎Carburetor setting is required.
◎Engine characteristics become closer to high rpm. →If I say that it has come to revolve, it does (laughs).
◎Cleaning will be necessary for the blisters.
Some people do not have the Merit to install the Power Filter from Demerit, but it depends on how you use it and the form you want to use it in.
The purpose is to set the intake and exhaust to match the current running conditions. 。 In such cases, we think the Power Filter is a logical part.
View detail
Installed on VIRAGO250
The size fits the intake of my VIRAGO 250 just right. The price is low and the quality is not bad, so I use it for other vehicles as well. View detail
Durable!
Colorful and good looking Fuel hose. In the product description section Vulnerable to ultraviolet rays." It was stated that the Is it less durable?" I was convinced that it was a good idea to buy it, but I don't see much difference in durability between it and the OEM fuel hose. I am recommending this product because it looks very different and cool! View detail
For those who feel more comfortable seeing what's inside.
[How is it used?
I purchased this product to refresh the hose around the fuel cock and carburetor of a vehicle I have owned for many years, as they have begun to harden over time, while keeping costs down.
Thanks to the fact that the same parts were used in vehicles up until recently, OEM parts are available for hoses, but they are a bit expensive, and the price is a bit high. CostCut" "Where commercial products can be used, CostCut uses commercial products." So I checked Webike and found that KIJIMA's Hose was cheaper this time, so I bought it.
Was the one you received as per Image?
The familiar Clear pink Fuel Hose, a supple and flexible Fuel hose, which is natural since it is brand new.
Incidentally, the OEM fuel hose we had been using up until now had no cracks, but it had deteriorated over time and was in a bad shape, making us glad we replaced it.
How was your experience with it?
We replaced the above-mentioned CaChicatiHose with this flexible product and everything is better.
The part used is a Carburetor drain hose, and the new one is good.
[Points to note]
Several different sizes of HoseLineup are available in the same package, so be sure to check the inside diameter of the hose you want to replace and order the size that fits.
How did it compare to other products?
I have only used KITACO and KIJIMA products, but I think they are both similar products and there is no problem no matter which one you buy.
I feel that the pink clear type fuel hose hardens a little faster than the black rubber hose, etc. If you do not neglect daily maintenance, there is no problem, but for a lazy person like me, it is better to check it once a year or so. I felt it would be better for a lazy person like me to check it once a year.
Other items that would be helpful
Point and hang of installation
I am not sure if I am doing it the right way, but if I apply a small amount of silicon grease during installation and insert it into the cook, it works Smoothly.
As a matter of course, let's pass the Clip through the hose first before jointing the hose.
The most Large-picture work may be to insert it firmly and prevent it from coming loose with a firm hose band.
[ITEMS TO BUY TOGETHER
The inside diameter of the hose from the fuel cock and the hose around the carburetor may be different, so be sure to check the inside diameter of the hose that was originally installed before purchasing the appropriate product.
If the Fuel Hose is replaced with a new one, it may be better to purchase a new Hose clip (Hose Band) as well, considering its deterioration over time.
[Opinions and requests to Manufacturer
Please continue to sell this product as long as possible, as it is necessary to replace the fuel hose on older motorcycles.
View detail
To Refresh around Fuel Cock
[How is it used?
I purchased this product to refresh the Fuel Cock area of my 27 year old SEROW225 WE.
Thankfully, Yamaha still sells the 1997 SEROW225 WE Fuel CockAssembly, but the price tends to be higher.
So, we searched Webike to try CostCut using the available Universal Product, and decided to purchase a Fuel hose made by KIJIMA, which we have been using for a long time.
Incidentally, the 1997 SEROW225 WE will need three fuel hoses, each PipeFuel1 for $715. Pipe2 for $1,331. Hose for $275. for a total of 2,321 yen. (The "Spring Compression" used for Pipe2 will be used again.) 。
Did you receive the item as per the Image?
It has the same inside diameter as the SEROWOEM Product and is a supple and flexible fuel hose, which is natural since it is new.
Incidentally, the OEM fuel hose we had been using up until now had no cracks, but it had deteriorated over time and was in a bad shape, making us glad we replaced it.
How did you like it?
We replaced the above-mentioned CaChicatiHose with this flexible product and everything is better.
The two-layer Type is a reliable and secure product that is resistant to breakage even when curved.
[Points to note]
Several different sizes of HoseLineup are available in the same package, so be sure to check the inside diameter of the hose you want to replace and order the size that fits.
Too thick will increase the risk of fuel leakage, and too thin will affect fuel flow.
How did it compare to other products?
My personal impression is that clear type fuel hoses in pink, etc. tend to harden easily, which is not a problem for those who do not neglect daily maintenance, but for a lazy person like me, a product like this with high durability and weather resistance would be safer.
Other items that would be helpful
Point and hang of installation
I am not sure if I am doing it the right way, but if I apply a small amount of silicon grease during installation and insert it into the cook, it works Smoothly.
As a matter of course, let's pass the Clip through the hose first before jointing the hose.
The most Large-picture work may be to insert it firmly and prevent it from coming loose with a firm hose band.
[ITEMS TO BUY TOGETHER
Hose clip if you have a new fuel hose. (Hose Band) may also be better to purchase new ones to account for age-related deterioration.
[Opinions and requests to Manufacturer
Please continue to sell this product as long as possible, as it is necessary to replace the fuel hose on older motorcycles.
View detail
MONKEYTachometer out-of-lighting measures
The lighting bulb of Takex Tachometer, which was installed in MONKEY, went out, so we installed KIJIMA's lighting bulb as a Universal Product, and it worked fine.
We will fit the product with confidence, so please use it as a reference!
View detail
I would like to make Carburetor a Large thing.
I put it on after purchasing a slightly more expensive Carburetor to prevent Rust and Garbage from getting into the Fuel Tank. The price is reasonable and it is well made and this is the third time I have purchased this product. View detail
I use it a lot.
It is useful to have one. Used for minor repairs and electrical custom work. I have not used it for a long time, so I am not sure, but I think there will be no adhesive residue. It is very easy to use and I like it. View detail
Essentials for Hose Replacement
Fuel Hose hardens and deteriorates, but so does the Clip:Rust, broken, spreading. It's also cosmetically good! View detail
I can't find anywhere that sells parts.
This is very helpful since there are no Motorcycle parts dealers nearby,
The product is cosmetically excellent.
View detail
For Stock
I have already purchased this product last time and bought it for Stock.
It's for old Custom parts,
In the countryside, items are difficult to obtain.
Thanks.
View detail
It was new and had some kind of Stain on it.
I installed it on a K&N filter and it held tight. However, there was a 5mm large stain on the filter even though it was brand new, but the cleaner did not remove it. View detail
Fits: KAWASAKI ZX-9R, KAWASAKI ZR-7/S, KAWASAKI ZEPHYR750 RS, KAWASAKI ZEPHYR400, KAWASAKI Z750 (water-cooled), KAWASAKI VERSYS 650, KAWASAKI ESTRELLARS, KAWASAKI ESTRELLA, KAWASAKI ER-6n, KAWASAKI ER-6f, KAWASAKI ZZR600, KAWASAKI ZZR600, KAWASAKI ZZR400, KAWASAKI ZZR400, KAWASAKI ZZR400, KAWASAKI ZZR250, KAWASAKI ZZR250, KAWASAKI ZZR250, KAWASAKI ZZR250, KAWASAKI ZZR250
Affordable as Repair
The Kawasaki OEM Lever is rather expensive, so I bought an external one as a replacement.
We are using it by transplanting the entire Holder to a vehicle without lever adjuster of another manufacturer.
It broke from the root when I fell on the Circuit, it is not as tenacious as OEM.
View detail