Reviews
In OEMHelmet holder
I have not been able to install it yet because the weather has been rainy on my vacation since I purchased it, but as far as I have checked Reviewetc., I think it is a highly satisfactory product.
Since the OEMHolder cannot reach the Helmet's Holder...
View detail
Fits: SUZUKI GIXXERSF250, SUZUKI GIXXER250, SUZUKI GIXXER150
That would be handy
The DL1000 V-STROM250SX is mounted on the same frame as the Gixxer 250, so no special modifications were required.
Wrap the Rubber around the Bracket and insert it into the Bracket.
*Because it is only clipped by Bracket, it is better not to run with Helmet hanging down, because there is a risk of it coming off.
I don't think I'll be using it much since I have a top case, but I think it will come in handy when I have a full load of souvenirs, etc.
View detail
I was relieved that it was as good as I imagined.
The vehicle used is z900RS.
Due to the convenience of installing the Side Back on the opposite side of the Exhaust System. The existing helmet holder could not be used.
Then, I thought of for Tandem, Helmet holder.
It can be installed on the opposite side of the existing helmet holder.
This product has arrived. It looks the same in appearance as the existing OEM product.
I wondered if the existing helmet holder could be attached to the bracket as it is, and it did so without any discomfort.
In other words, the Helmet holder that can be used with the Engine key arrived on the opposite side of the existing one.
View detail
Useful if you have it ^^.
[How is it used?
When you stop at Convenience or some other place where you stop for a bit.
Was the one you received as per Image?
Large Image Street
How was your experience with it?
It did not go into the CYGNUS Hell Lock pin as is.
[Points to note]
The pin holes are unexpectedly small, so some modifications may be necessary depending on the vehicle.
How did it compare to other products?
No comparison
Other items that would be helpful
As a side note, the included Carabiner is too small.
The 100 yen shop items of today are of higher quality.
View detail
Helmet is now easier to lock.
I was having a hard time using the helmet holder that I moved when I replaced the rear suspension made by Y's Gear, and when I locked the helmet, it was close to the engine, so I had to be careful about the mounting angle, etc. I saw this product on SNS and thought it looked good, so I bought it.
Tandem Footpeg and Bracket are attached by co-tightening, but our car is equipped with SSB GymkhanaBumper and Quantity:Since the Slider in the set is attached in place of the Tandem Footpeg, the Spacer included in the product was not used.
I was able to install it without hitting the frame.
The OEM lock part was available as is, so the part used in this product was Bracket Only, but I am still satisfied with the ease of locking.
View detail
When parking
Easy to attach to a helmet holder when connected to a D-joint View detail
Fits: HONDA CRF1100L Africa Twin DCT, HONDA CRF1100L Africa Twin Adventure Sports ES DCT, HONDA CRF1100L Africa Twin Adventure Sports ES, HONDA CRF1100L Africa Twin Adventure Sports DCT, HONDA CRF1100L Africa Twin Adventure Sports, HONDA CRF1100L Africa Twin, HONDA CRF1000L Africa Twin DCT, HONDA CRF1000L Africa Twin, KAWASAKI Ninja 1000SX
Purchased because I don't have a Helmet holder.
The 2012 ninja 1000 does not have a helmet holder, so I bought one instead.
The License Plate Holder I had before had a helmet holder, but when I used the Luggage Hook, there was a possibility that the number would be slightly hidden, which would be a violation of the Road Traffic Law. Therefore, I changed to KIJIMA's License Plate Holder with Helmet Holder.
After installation, NORMAL will not interfere anywhere.
In my case, I am changing the License PlateMounting Bolt to a Security Bolt.
It is better than the previous License Plate Holder in terms of refreshing, but like your review, I am not satisfied with the need to carry two Keys, so I gave it 4 stars.
I am satisfied with the rest.
View detail
Fits: DUCATI Panigale V4, DUCATI Panigale V4 S, DUCATI Panigale V4R, DUCATI Streetfighter V4, DUCATI Streetfighter V4 S
Helmet can be fixed!
[How is it used?
Because it is used without Tandem Footpeg,
There is no difficulty in attaching the Helmet to the Holder.
Was the one you received as per Image?
It is as per Image, as I used to use it on a CBR I used to own.
Was the installation difficult?
Installation was easy, as there is no Tandem Footpeg.
In order to match the color with the periphery, a separate Hexagon Socket Bolt was prepared instead of the supplied Bolt.
When adding the TankUnder Cover, a collar was added between the Holder and the TankUnder Cover, and the Bolt was also replaced with a longer one, as it interferes with the Holder.
How was your experience with it?
Because the Helmet interferes with the Swing Arm and Rear Fender, a ShopTowel is placed between them.
[Included Parts:were they on?
An installation Bolt was included.
[Was there anything that disappointed you?
I felt that it would be good to have the mounting bolt in black to unify the color with the bracket.
View detail
I can't do without it.
I was looking for OEM helmet holders and found this one in Aftermarket parts. The installation itself is easy with ScrewQuantity.:It is easy to remove 2pcs, but this Quantity:The 2pc screws were so tight with the locking agent that it was very hard to get them off. It's not that the product is bad, but the installation was more strange than I expected. View detail
Fits: HONDA PCX eHEV, HONDA PCX125, HONDA PCX150, HONDA PCX160, HONDA GROM
I think it is convenient.
Quality and texture information is well finished in chrome The helmet lock has become easier to use for the feeling of use Product to buy together Product # P00040 makes it easy to fix your helmet It's difficult to install Cost performance and comparison with other products, but with high completeness About Shipping and Packaging The concern when purchasing is that collecting and purchasing information first can save time and money to see if it is possible to install I bought this product because I couldn't use the std helmet lock of Monkey 125, but I'm satisfied View detail
Buy again
Quality and texture information Rubber-covered wires the right length to use Design Information Loop Line Size Chart Information 44 cm Excellent cost performance and comparison with other products WeBike packaging is always great. Arrives in a week for delivery and packaging Concerns, caveats, or advice on purchasing The helmet holder on the Monkey 125 fits in a really crazy place. So you can't wear a helmet without this wire. I really recommend it I bought two, and I'm using one as a side bag and one as a helmet lock The side bag comes off while driving, so you can fix it and use it View detail
Small but essentialItems
[How is it used?
It is used for CBR1000RR-R.
Was the installation difficult?
Installation is very easy as it is simply secured with the OEM Bolt that holds the Tandem Footpeg in place.
[Was there anything that disappointed you?
No, it is not. It is an indispensable item, as many OEM cars are equipped with it these days.
View detail
Easy to use
Loading the Pannier case makes it difficult to hang the Helmet on the Holder, but it can be easily locked.
In the case of crf250l, the Holder seems to pop out to the side due to its shape, but it eliminates interference with the Body and makes it easier to remove.
View detail
Fashion and practical
It is used together with Helmet lock for DL1000 V-STROM250 only.
It is for SHOEI's Ratchet lockHelmet, but I like the SMART design better than the Universal Type, so I use it on OGKCUBE's RYUKI and WINS's A-FORCE RS.
I love the bright AnodizedRed in Fashion! (In the photo I uploaded, it looks orangey, but with the naked eye, it is really bright bright red.) 。
This product requires a little extra effort to attach and detach, but it is worth it for Smooth attachment and detachment.
Conversely, I'm not satisfied with Body's Spec. which makes it difficult if I don't bother to buy this, or I feel something like MatchPump….
However, it is inexpensive and looks good as a Key HolderAttachment, so I am satisfied overall.
View detail
perfectly (suited)
It can be attached by simply removing two bolts from the bracket of the Tandem Footpeg.
I'm sure that can be stolen for that, but the same thing goes for the locks on the OEM on the other side.
We have converted it to one-key (can be opened and closed with Motorcycle key) by referring to other sites.
View detail
Somewhat difficult to use...
Used on a ZX10R '24.
The box said it was for 16-17 year models, but the compatibility is perfect.
No problems at all.
The ZX-10R does not have a helmet lock, so I have to attach it myself,
The two choices are Largebody Babyface or KIJIMA.
This one is like a lock coming between the Tandem Footpeg Bar, so to be frank, it is difficult to hang a Helmet.
It may be even more difficult to install because people who ride ZX10R are almost full face.
If you get used to it, it is no problem, but if you install it roughly, the motorcycle and helmet will rub against each other,
Be careful when locking, even if it is troublesome.
View detail
Fits: BMW R1200R, BMW R1200RS, BMW R1250R, BMW R1250RS, BMW S1000RR
Helmet holder can be attached to SS
[How is it used?
Used for storage of Helmet
Was the one you received as per Image?
It was identical to the photo shown on the website.
Was the installation difficult?
Simply remove the Rear Footpeg and reinstall it across the Bracket.
Very easy.
Be careful with tools because the bolt is a torx bolt.
When installing the key on the bracket, be sure to follow the instructions for attaching the Screw Lock to the Screw.
How was your experience with it?
The Holder makes me feel very safe when I leave the Motorcycle.
Since the helmet comes exactly at the rear footpeg, care must be taken not to scratch the helmet.
It was available for the 2023 MODEL.
I had a hard time with Speedra's Helmet lock, but the mounting points will be in the same place.
However, KIJIMA's product has an extended bracket and can escape from footpeg, so this is adopted.
Speedra was forsaken for installation in the same location as the footpeg section.
Babyface was also considered, but the key part is shaped like Straight when it is opened,
I thought about the possibility of Helmet falling off, so I stopped.
KIJIMA and Speedra are expected to prevent falling due to their U-shape.
The frame is black and the bracket is also black, so they are the same color and inconspicuous.
[Included Parts:were they on?
None in particular
[Was there anything that disappointed you?
None in particular
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
helmet lock
JA65 CT125 Korean model also fits well. Installation is relatively simple by removing/attaching the seat hinges. A bracket is installed at the bottom of the seat hinge, and the locking mechanism is bolted to the bracket. It is designed so that the bolt cannot be unlocked in the locked state, and the anti-theft effect seems appropriate. Since it is a single cylinder with severe vibration, it seems that a threadlock is needed for the fixing bolt. View detail
I installed it myself.
There is no Instruction Manual and installation was quite tedious. There was a video showing the removal of a plastic board? I saw a video of a person taking off a plastic board and installing it, but was it too much for an amateur or was I not good at it? It was a bit too much for an amateur. In the end, I managed to install it by shifting it, but it got some scratches on the steel bar. View detail
Easy to use
I lock it through here because I have experienced that the chinstrap of the helmet was cut and the helmet was stolen.
I guess it's a little harder to steal.
View detail