Reviews
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Partially made of Steel, it is prone to rust.
[How is it used?
The Normal pedal was a bit tasteless, so it was attached to the Brake pedal version up.
Was the one you received as per Image?
The size was larger than expected and easy to step on.
Was the installation difficult?
Install the Normal brake pedal so that it is sandwiched between the Normal brake pedal.
Plus screw allows installation with a single Driver.
How was your experience with it?
The driving operation is easier because there is more area to step on.
However, it took some time to get used to it because of the slight increase in height.
[Included Parts:were they on?
Mounting Screws, Mounting Hardware, etc.
[Was there anything that disappointed you?
Body is Material:Aluminum, but the Plus screw and the bracket on the reverse side are rusted with steel. Especially when the Plus screw is rusted, it is difficult to remove it.
▼This is a common design, but you can enjoy a slightly Mischief atmosphere.
I think the discomfort during operation depends on the person.
View detail
Rubber thick!
It was a bit pricey, but I bought it at the Shop because it didn't seem to be in stock at WeBig.
I have a GB250 CLUBMAN with Back's Tep, but the Rubber is worn out and I think the Rubber thickness is a bit more Shift change feeling (I just put it on and haven't run it yet). (I haven't run with it yet, just put it on.) It looks more durable because of the thicker rubber.
View detail
Position is good. Attached Screw is easy to lick.
The attached mounting bolt is easy to lick. Is it soft? View detail
Fits: SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI GSX-R125, SUZUKI GSX-S125
It will be a comfortable position.
I test rode the GSX-R125 before purchasing it and felt uncomfortable with the footpeg position.
So I installed this Footpeg Plate when I bought my new car and have been using it since new.
The condition is good in Large and also good in Sports driving in Circuit.
I think it is essential Items for GSX-R125.
View detail
Easier to obtain than OEM
The OEM change rubber was getting worn out and I was thinking of replacing it, but it was too much trouble to ask for the OEM Product, so I decided to go with this one I found at a Motorcycle supply store.
I bought it without measuring the size, but it is almost the same size as OEM and I was able to install it without any problem.
The old OEM product is not reused, so it is cut with a cutter, and this product can be easily installed by using Parts Cleaner as lubricant and pushing it in.
The operating feel is not too different from the OEM, neither better nor worse.
View detail
Fits: SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI GSX-R125, SUZUKI GSX-S125
Step Up Bracket
I think it would have been better to have a part that collapses like the Change Pedal on the Off car, where the Normal step is longer and the Knee Slider is sharpened. View detail
Fits: HONDA Super Cub 70, HONDA MD50, HONDA MD70, HONDA MD90, HONDA Super Cub 50, HONDA Super Cub 90, HONDA Little Cub, HONDA Benly CD90, HONDA Benly CD50, HONDA press cub, HONDA solo, HONDA Ape 50, HONDA Ape 100, HONDA XR50, HONDA XR100, HONDA DAX, HONDA Chaly, HONDA Little Cub, HONDA Benly CD90, HONDA Benly CD50
Is it an individual difference….
The rubber on the Brake Side was easily replaced, but the Shift Pedal side seemed to be made much tighter and could not be inserted all the way in.
The quality is solid, and considering that it is a consumable product, I think it is sufficient.
View detail
Mostly satisfied
[How is it used?
Installed and ran for about 200 km. Tuned to the higher setting.
Was the one you received as per Image?
Street Image
Was the installation difficult?
Easy
How was your experience with it?
Can be firmly converted to Rear Sets
[Included Parts:were they on?
There was a minimum of Included Parts:required
It would have been better if it had a Tie Band, because I had to turn off the Tie Band when I set it to the higher setting.
[Was there anything that disappointed you?
nothing special
Other items that would be helpful
The installation was not difficult, and I recommend it to those who want to convert to Rear Sets easily.
Side Stand hooks turned easily when I put my weight on them.
View detail
Cushioning is good and Change is easy!
[How is it used?
I replaced the OEM Rubber on the Change Pedal, the cushioning is better and the change is easier.
Was the installation difficult?
I'm using it through an 8mm Bolt so it was easy to just thread it through the Bolt.
How was your experience with it?
The inner diameter is just 8mm. The outer diameter is 20mm, so it was larger than what I had imagined, but I think it's just right for the Cushion.
[Included Parts:were they on?
None
[Was there anything that disappointed you?
The texture is cheap for the price.
View detail
Fits: SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI GSX-R125, SUZUKI GSX-S125
I bought one, but it might have been wasted on this model of car.
I bought it thinking that it would be Custom, but I realized that it would be more cramped if I upstayed it in position, so I didn't install it.
I shied away.
View detail
Shame about the included Bolt.
The Position can be adjusted to two levels. It is a pity that the quality of the included Hexagon Bolt is not very good, there is play between the Hexagonal Wrench and the Bolt. View detail
It's a little lower than I expected.
You can make some Rear Sets.
You can see the amount of change and it is recommended for low Handlebar.
But Link Rod is short in NORMAL.
Please make sure you adjust that area.
The person who cares might be concerned because footpeg is going to appear outside.
It's cheesy.
View detail
So so
I like the Position very much, but the included Bolts are of poor quality It is impossible to tighten the bracket of the included bracket completely because it touches the OEM bracket It's about half the price of the original one View detail
It's a thing, but …
It's what's called an Ideas product type
I think it's good for people who don't need Rear Sets, but footpeg is not enough
However, the Bolt's accuracy is not so good I did … the M8x40 Bolts are the worst quality I bought a new Bolt separately, so you should be prepared to pay for that
I used the proper tools, and the strength of the hexagon holes doesn't match the tightening strength
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey, HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
A little stylish with Small items?
NORMAL's Brake pedal is a little Small, definitely
As my fingers and groin usually hurt to use around the thumb of the foot usually [I only?) There is a feeling of uneasiness or try to improve slightly Brake pedal a thing color!
Large If you do not want to wear it, do not worry too much! And at an affordable price! If possible, if you have a little playfulness ○
So I chose KIJIMA's footprint Pedal cover. Painting is peeled off if used, so we selected no painting.
This product is Parts for Mongoli, APE,
I also purchased it with playful spirit that it could be diverted to any type of car for the impression.
Installation was possible without problems.
However, in order to pinch this letter Plate of the attached Parts in PedalSIDE, the Size of the part to be fitted is Small and the direction is reversed (I flipped it over) It was quite easy to install. If you are worried if you worry if you are worried Tie Wrap with Bolt from the part of Bolt Let's pass through the part of Peda Lure It'll be durable Large It was Large I was trying to use it.
Feeling feeling is felt comfortably felt widely stepped width than NORMAL's toes only.
Also, footprint Design preference can be separated but I purchased it with playful spirit. Large I feel a little Large, but I usually do not mind as I can not see from the side around my feet while driving.
View detail
Fits: HONDA JAZZ, HONDA CROSSCUB110, HONDA SUPER CUB110, HONDA CUB, HONDA MONKEY
Since it can not be installed, it can not be evaluated
There was LITTLE CUB in the compatible model, but my rating was not fitted to my LITTLE CUB, I could not install it, I can not evaluate it, but the texture was nice.
View detail
Fits: HONDA CUB [CUB] Super Cub (Standard 12V), HONDA Ape 50, HONDA Ape 100 Type D, HONDA CUB [CUB] Super Cub (Custom 12V), HONDA CUB [CUB] Super Cub (DX 12V), HONDA CUB [CUB] Super Cub (Business 12V), HONDA Ape 100, HONDA little cub, HONDA Ape Type D, HONDA CUB [CUB] Super Cub (Standard 12V), HONDA Ape 50, HONDA Ape 100 Type D, HONDA CUB [CUB] Super Cub (Custom 12V), HONDA CUB [CUB] Super Cub (DX 12V), HONDA CUB [CUB] Super Cub (Business 12V), HONDA Ape 100, HONDA little cub, HONDA Ape Type D
Color variations are ...
Quality itself is OEM same etc. Although it seems, it is an impression that it is slightly less than OEM.
The installation itself was done without difficulty.
I made the color Dark brown, but even by just setting footpeg to Dark brown
The atmosphere of the car changes for a long time.
By the way it is a price that does not differ from OEM, but it is Merit that there are color variations.
It might be better to buy OEM for Black color.
Dark Brown and Black are only strange colors, so a little more exquisite Color
I hope Variation will increase.
View detail
Is it good well? since it obtained even if affinity with safety shoes was seemingly bad and it could delete at the uncanny speed and more than half was lost although he hoped such a thing and that you hardly exhausted, he bought this with things. Sinc
Is it good well? since it obtained even if affinity with safety shoes was seemingly bad and it could delete at the uncanny speed and more than half was lost although he hoped such a thing and that you hardly exhausted, he bought this with things.
Since the pure twist was also thin at first, it regarded as ? whether the feeling of a shift change would change, but there is also no sense of incongruity of the neighborhood, and if it thinks from the amount of money, I will think that it is enough.
View detail