Reviews
Refreshing fit in Handlebar.
I asked PRO to put it on, but it seems that I need to be creative with the wiring, so they connected it in a way that does not put a load on the Battery.
It fits nicely in the Handlebar and looks good.
View detail
Although the shape is different from those made by Ekimon, Yaoki, and others.
The Crimp section has not been modified in any way, such as being slightly folded from the beginning, so it is a little troublesome to Crimp with Electric Works Pliers, but it is good for Crimping several thick or thin Cables at once.
In addition, the sleeves for waterproof and insulation are a little thicker than those of the Title companies, but there were no particular problems when they were mixed with those made by those companies.
View detail
It's a safe and reliable product.
I purchased this product because I needed it to get an earth reading for the installation of a DriveRecorder in my car.
The product is an ordinary Stag beetle terminal, but it is solid and not unreliable with PelePera. It is a safe and reliable product.
This time, I combined this terminal with a 0.75 cord to make Minus Wiring. I am planning to redo the wiring for Motorcycle's DriveRecorder- etc. in the near future, so I would like to use the rest of this time for Motorcycle.
Well, it is one of those things that you want to Stock because you will often need it.
View detail
Fits: SUZUKI SV650X ABS, SUZUKI SV650 ABS, SUZUKI GSX-S750, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI DL1000 V-STROM650XT, SUZUKI DL1000 V-STROM650, SUZUKI GSR750, SUZUKI DL1000 V-STROM1000
I installed it on my GSX-S1000.
I used it to install an external blinker, but since it was a rear blinker, the wiring was not long enough, so I had to extend the wiring. It would have been better if the wiring was a little longer. View detail
Purchased to fix Hose on Tank.
Purchased to buy Tank's Hose.
There are two Band sections, so I think they are holding it in place.
Installation is as simple as turning the Screw with the Driver.
However, there is no prominent notation on the Package, but this is Steel, so you want to be careful of rust.
I can recommend it.
View detail
Wiring Protection
Used to wrap Wiring, easy to roll, soft, elastic and good looking, but a little expensive. View detail
For rainy day measures.
I bought this Coupler because the original Coupler was not waterproof specification. It's a bit large, but I think it's safe for rainy days...? View detail
Ideal for securing the Earth of the device to the Bolt of the vehicle.
I use it to hold the Earth of the electronics firmly in place through the Bolt on the car body.
The Stag beetle type would have been fine, but it would have fallen off while removing the Bolt. This perfectly round product is attached to the Bolt properly, so there is no need to worry.
Just be careful because you need to remove the Bolt completely.
Also the Sleeve is properly Quantity:It is safe because it is Set.
View detail
The size is a little large, but the practicality is perfect.
[How is it used?
ai-net i-Net Waterproof Mini Flat Type Fuse Holder MINI Flat Type is used to protect PL Insurance Products outside the car. The Fuse holder itself is waterproof, but in order to increase the degree of waterproofing, this Wiring Cover is also used together.
Was the one you received as per Image?
It's a little bigger than I thought it would be.
Was the installation difficult?
It's not difficult at all because it's just threading a cable, but it was difficult to find a place to place it because the body is large.
How was your experience with it?
I wrapped it with WaterproofTape because rain enters from the part where I pass the cable.
View detail
It is indispensable for Wiring processing.
The Tie Wrap is a must-have for Custom and Maintenance, whether you are putting together a Wiring or protecting it. It is very durable and good quality and can be used in many situations. The length is easy to handle and easy to use. View detail
Fits: YAMAHA NMAX, YAMAHA CYGNUS X SR, YAMAHA NMAX155
I was able to use it on my Ninja 1000.
I used this on a 2017 Ninja 1000; I took power for Relay operation from the Coupler on the License Plate Light.
Just by interrupting the Coupler, you can get the power supply without modifying the lines of the vehicle.
For Ninja1000, Plus and Minus are reversed, so it is necessary to remove the pin from Coupler and replace it or replace Bullet Type Terminal.
The cable is thin, so it is better not to connect the electrical equipment which needs large current.
In my case, I changed the License Plate Light from a bulb to an LED and decided that it was not a problem because I use only the power supply for Relay operation.
There are also Couplers that are similar in shape to the common Waterproof 2-pole Coupler, the MT090WaterproofILSeries and MT090WaterproofALSeries are slightly different in shape. Check your vehicle's Coupler carefully before purchasing.
View detail
Fits: KAWASAKI ZX-25R SE, KAWASAKI ZX-25R, HONDA REBEL500, HONDA CBR650R, HONDA REBEL250, HONDA CB1000R, HONDA CB650R, HONDA Rebel300
TankUp
Just remove the Coupler and put it in between the two. It's easy to get the power supply. But for the CBR650R, you have to put it on the coupler on the left side of the tank. It depends on the type of car, but it took me about 2 hours. View detail
It's just the right amount.
It is an appropriate amount for replenishment. Because the frequency of use is frequent, it is also early when it runs out though Large always takes an active part to take power supply and Attachment power supply at all times. It is inexpensive in sufficient quantity as a replenishment use because I do not need that much Large quantity. View detail
Fits: SUZUKI SV650X ABS, SUZUKI SV650 ABS, SUZUKI GSX-S750, SUZUKI GSX-S1000F, SUZUKI GSX-S1000, SUZUKI DL1000 V-STROM650XT, SUZUKI DL1000 V-STROM650, SUZUKI GSR750, SUZUKI DL1000 V-STROM1000
Convenient Goods
I bought it to change to LED Blinker
No need for wiringCutting, less time spent on the job and better appearance (^^) v
A little more Reasonable would be nice?
View detail
It's a little expensive, but I'm happy with Wiring's results
Other Brand from Z125PRO's OEM CellKill switch Used to replace the Product
I could have wrapped it around the tape instead of this product because it's not normally visible I want to return it to the same way as OEM parts, so I use this wiring cover
I am satisfied with the condition of the replacement as it is the same shape as the OEM parts
View detail
LEDCustomTail Lamp To install it !!!
WEBIC mode : I bought LED custom tail light smoke for installation on Grom. WEBIC mode : LED custom tail light coupler connected to smoke is different from grom genuine shape, if you examine it : Coupler housing was waterproof type 3 poles HM 090. I think that it takes less than 10 minutes if you are working on wiring. Just to be careful ? ? ? Pay attention to the direction of the waterproof packing attached to each wiring. Because there is no manual also attached here, Google Mr. resorted to Mr.. Another one is a one-shot game because there is no terminal reserve. If it fails and the terminal is damaged, the terminal for HM 090 comes out to Yahoo auction so please rest assured. Also in my experience, as a certain case record ? ? ? When wiring was connected to the terminal and connected to the coupler, only the terminal remained in the coupler, and the connection was disconnected!. Terminals can be removed from the coupler even at such times. Removal tool minus precision screwdriver (Very small size) is. Although a bit of knack is necessary, you can remove the failed terminal from the coupler, so please do not give up! Connection ? Experience and correct tool selection are necessary for terminal crimping. Perhaps tools are also available for purchase at Webbec, so why buy them at the same time? View detail
Just in case...
I do not think it is necessary because it does not ride when it is basic rain, but sudden rain and car wash etc. In mind when considering when Motorcycle gets wet. It looks like insurance.
Used for Power Sub Harness of Y's Gear.
View detail
Somewhat expensive but useful
Although it is somewhat expensive, it does not differ from the Large difference that I buy it with SocketSingle Item,
I bought it because I have no trouble.
Speaking of the fact that Plus and Minus are all plug receptacle,
The code's Length is short..
I just want Plus's Line to be of Male type.
View detail
[Webike Monitor] When the Meter made from a yell Well ACE-2802 was attached to a D tiger, it was used for wiring processing for using a pure Speed sensor. Having used it is not using the Coupler only with a terminal. The triangular type wat
[Webike Monitor] When the Meter made from a yell Well ACE-2802 was attached to a
D tiger, it was used for wiring processing for using a pure Speed sensor.
Having used it is not using the Coupler only with a terminal.
The triangular type water proof Coupler of the
photograph was also fitted satisfactorily.
The pliability of the
Seal is high and it expects waterproof performance.
If [ if the
price is / the back / somewhat cheap ] - ^^
View detail
the electronic autoparts which had taken the Earth with the mulberry type terminal are sometimes separating now and then in slack of a battery terminal -- -- it taking with a mulberry type terminal, when severe in the Space where that of rou
the electronic autoparts which had taken the Earth with the mulberry type terminal are sometimes separating now and then in slack of a battery terminal --
-- it taking with a mulberry type terminal, when severe in the
Space where that of round terminals is positive if an Earth is taken certainly, but.
If it is a place which can be taken, use of round terminals is trustworthy!
View detail