Reviews
Fits: KAWASAKI ZX-25R, KAWASAKI ZX-25R SE, KAWASAKI NINJA2 Helmet50R EX250P
I don't want to hurt OEMHarness.
I want to use CouplerON as much as possible, because cutting OEM harnesses is a source of trouble.
Considering the price and construction, this is a very expensive product, but the advantage is that it does not damage the OEM's harness.
Installation is easy. In the case of the Ninja ZX-25R, remove the DummyCoupler and insert this product into the DummyCoupler.
The original DummyCoupler is simply attached to the Coupler on the other side of this product.
After installation, an energization test was also conducted.
Checked with Tester and no problem.
View detail
Fits: SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125S, SUZUKI ADDRESSV125S, YAMAHA CYGNUS X FI, YAMAHA BWS125(BWS), YAMAHA Axis Treat
High beamWiring
Mounted on Axis Treat
Purchased to add USB power supply
USB power supply cannot be used unless High beam is ON at High beam in Wiring.
View detail
Kiboshi Terminal Set
Quality and Texture Information Typical Jiboshi Terminal Set Full of Male Terminal for usability Product Inquiry Crimper To Buy With, Female Terminal Easy to install Cost performance and comparison sets with other products are affordable WeBike packaging is always great. Arrives in a week for delivery and packaging I ordered it after looking at the word "set" to see if the translation was wrong when I bought it, but only the Male Terminal came and checked the site again, and the notice came up that there were 8 Male Terminals. I need to order again because it's internalism. It goes well with Honda View detail
For branching
This is for use as a branch of a power supply.
110" 2PConnector, Pin Quantity:Set, but it would have been enough if we could have connected with other cheaper ones.
View detail
Hazard Switch.
To the Hazard switch on the CUB.
It looks like a HazardButton, which is good.
View detail
suzuki V-strom650 L8
Interrupt Harness to secure the power line because we don't want to damage the Wiring View detail
that's all right
Used with EngineWiring protection. It looks better than the Sbiral Tube. I think it is good for engine wiring protection, especially for LargeEngine Displacement Volume Motorcycle with high engine heat. Cost is high and it is difficult to install. View detail
Necessities
This Tie Wrap is just the right thickness to hold Wiring together.
It is durable and of good quality, making it resistant to deterioration over time.
They are useful in a variety of situations.
View detail
Looking forward to the performance…
I used it through the Controller's Wiring of Sub computer.
I used it for the USB cord to connect to my PC for setting, but I was worried about the heat because I had to put it along the frame.
I did the construction with this Self-wrap Sleeve expecting the flame resistance and the heat resistance. So far, the problem has not occurred, so I guess we'll see.
View detail
Easy to install as it is exclusively for the model
I bought it without knowing where to use the connector, but the Instruction Manual is attached
It was relatively easy to install. Harness is thin, I will come to you.
View detail
Fits: SUZUKI ADDRESSV125, SUZUKI ADDRESSV125, SUZUKI ADDRESSV125S, SUZUKI ADDRESSV125S, YAMAHA CYGNUS X FI, YAMAHA BWS125(BWS), YAMAHA Axis Treat
Recommendation for Custom's time
【What made you decide the purchase?】 Reducing the effort of Wiring process at Custom.
【How was it actually used?】 It's easy because Extra Processing Not Required.
【Was it difficult to install? (Hard parts case)】 It's easy to just cheat.
【Please tell me the point of installation and hang (in the case of Hard parts)】 Any
【Fit feeling and height when wearing - Please tell me the weight etc (Apparel case) 】Any
[Is there anything I was disappointed about?] None. I am satisfied with this price.
【Hope for Manufacturer - Please tell me if there are any improvement points] No. I do not want out of print.
【Have you compared items?】 None.
[Others] Any
View detail
Fits: YAMAHA NMAX, YAMAHA CYGNUS X SR, YAMAHA NMAX155
Wiring refreshing
Purchase for NMAX USB power supply retrieval. I tried connecting the USBConnector with the prepared Bullet Terminal but do not energize. Apparently when using it with NMAX, it seems that it will not normally turn on unless - side is taken from Body rather than Bullet Terminal. If you contact Manufacturer, it seems to work normally with CYGNUS. View detail
Fits: HONDA FAZE, HONDA FORZA(MF10), HONDA PCX150, HONDA PCX125
In PCX, Wiring is reverse
I purchased this product because it is Large strange to buy Socket.
It is convenient to take ACCWiring, but if you check the Wiring diagram, it seems that Red is connected with Earth, Black is connected with ACCPlus Wiring, and Image is the reverse.
I think that it is better to check Wiring without believing the color.
It's more secure than just processing Oiring Wiring, so it is recommended not to make even a color mistake.
View detail
KIJIMAKIJIMA Conversion Harness
I changed from Bullet terminal to this Coupler. Especially it is not possible and it is not impossible, but Refreshing that the removal can be done with One-touch and it looks refreshed. View detail
Although I think that it is also what much Manufacturer would produce last, the thing here can choose the Size of die length and is convenient.Since it is convenient, it often uses.Although the thing of the other company was also used, durability felt the
Although I think that it is also what much Manufacturer would produce last, the thing here can choose the Size of die length and is convenient.Since it is convenient, it often uses.Although the thing of the other company was also used, durability felt the thing here as OK ?? from the feel taken in its hand.How much it has has room for improvement. View detail
When it equips with a Side bag, it is used for connecting the fixing belt on the main part of a Motorcycle, and the Bag back side. It was not extended like the Nylon string attached to the Bag, and since it is dismountable at a Release type, it is sa
When it equips with a Side bag, it is used for connecting the fixing belt on the main part of a Motorcycle, and the Bag back side.
It was not extended like the Nylon string attached to the
Bag, and since it is dismountable at a Release type, it is satisfied in a user friendly manner.
Although it can release how many times or durability is unknown, I think that a Cost performance is also good.
View detail
It was used for attachment of a fuel filter. Since attachment in which the Screw stop is more positive than the Clip can be performed, sense of security can be incurred.
It was used for attachment of a fuel filter.
Since attachment in which the Screw stop is more positive than the
Clip can be performed,
sense of security can be incurred.
View detail
While the rubber cover has started and a waterproof effect can be expected, soldering of a terminal shows the handle side only by circular rubber packing being attached.... This point is an improvement required. Moreover, since two cords are separate,
While the rubber cover has started and a waterproof effect can be expected, soldering of a terminal shows the handle side only by circular rubber packing being attached.... This point is an improvement required.
Moreover, since two cords are separate, I hope that it can be collectively given by a tube etc. (we collected by the tube on hand).
Since texture, such as a feel of a design switch, is good, I want it to add improvement.
View detail