Reviews
It's just like that.
[How is it used?
To prevent paint from peeling and rust on my KLX125 that I bought with the intention of using it for mud play etc. Let's put a Film on the Frame." I decided to try something other than a transparent protective film, and after examining various options, I arrived at this product.
How was your experience with it?
As of 2024, similar products are available from various manufacturers at reasonable prices, but at the time of purchase (about 10 years ago), there were few of this type of product and it involved a fair amount of expense.
However, the adhesive strength of the film is high due to the fact that it is Seat made by 3M, and it is a very good product because it can be firmly attached to round pipe-shaped areas and some unevenness with heat from Dryeretc.
the last "Carbon Style" So, if you look at it up close, you can easily identify it as a fake product, but if you look at it from a distance... it is not so bad.
How did it compare to other products?
At that time, there were still few products of this kind, and there were no comparable products at the time of purchase, but compared to similar products in recent years, the adhesive strength is not inferior, and it is hard to peel off at the place where the adhesive is firmly attached by following the procedure. The adhesive is so secure that it is durable as long as you do not intentionally peel it off even when washing your car using a high-pressure washer.
[Points to note]
Free to Cut Seal." So, make sure to carry out the process before applying (Rust, dust and oil removal, etc.).
Other items that would be helpful
The deciding factor in the purchase
Strong adhesive strength to fix even OEMAeropartsetc. of a car with Double-sided Tape. Made by 3M. I think this was the most important factor in selecting this product.
[How is it used?
As mentioned above, it is used to prevent Wound on Frames and other steel product parts that would look bad due to Rust or scratches if left in place.
【Included Parts:presence or absence】.
One 300×400mm Seat and one sheet of paper with product description & how to paste Guide.
[ITEMS TO BUY TOGETHER
If you want to use it on a complicated shape or over a large area, use a degreaser (parts cleaner, Enamel thinners, etc.), and if you want to use it on a place where you can see if it is rusted, use a rust remover (wire brush, sandpaper, chemical products, etc.) and a rust remover afterwards. and a rust remover afterwards.
If you have a pen-shaped art knife (Scissors or Cutter) for shaping, it will be even easier to cut the excess portions.
Opinions and requests to Manufacturer.
It would be useful to have a larger (500×1000mm or so) film for wide-area use.
View detail
Pitta for Helmet.
This is my second purchase, I put it on my Helmet. View detail
3M Carbon Seat
Used on GSX-R1000R
Carbon Seat made by 3M.
If you are simply looking for a carbon seat, there are many different types available from various manufacturers on Amazon.
Recent Trend (?) is on top of the Carbon Style layer. [Color] It is a Clear layered Type and looks quite Real in the photo.
But when you buy it and get it in your hands, it”s not so bad. I'm not sure how much I'm going to be able to do with it, but I'm sure I'll be able to do it.
On the other hand, this is a one-layer Carbon Style Seat with a three-dimensional fiber pattern on the surface.
It may be a step down in terms of”realism”, but”Material:I think it is a reasonable Quality for a Carbon Style Seat”.
A notable Point of this product is its functionality.
The glue side is a groove (?) The surface is processed as shown in Figure 1, and can be applied without water or air bubbles.
The adhesive strength is exquisite and easy to apply and peel off, so it can be applied and reapplied many times, and it can also be peeled off cleanly without adhesive residue even if it has been applied for a while.
Also, if heat is applied at the time of pasting, it can be pasted while extending it considerably, so it has good tracking properties.
In R1000, it is attached as an anti-scratch pad on the side of the tank, which tends to be scratched by Pants' Rivet during handling.
I had originally applied a special colorless Seat, but it quickly became tattered and didn't last long.
This product, on the other hand, is resistant to slippage and has stuck on for more than two years without any problems.
This is a product that is often Repeat in Car/Motorcycle.
The only drawback is the price, but it is a very cost-effective product if you consider that you have to repeatedly buy cheap products and reapply them many times.
View detail
To MONKEY125.
I bought it together with a Brake pedal cover (Plating) made by KIJIMA, it is smaller than I expected, but the texture is good, I put it on the side cover. View detail
It can be attached to Handlebar, Mirror, and other curved surfaces!
[How is it used?
Plating on the Arm portion of the Mirror has peeled off, so we used it for protection.
Was the one you received as per Image?
It was smaller than I expected, but the design was just like the image.
Was the installation difficult?
It is easy to apply.
I curved and attached it to the Arm section.
How was your experience with it?
It has not peeled off and is firmly in place.
[Included Parts:were they on?
Included Parts:Not available.
[Was there anything that disappointed you?
Not much can be expected in terms of durability.
Parenthesis looks good when attached to ▼Cowl or Handlebar.
View detail
It was applied beautifully.
I was generally satisfied with the results, although it may or may not look like carbon depending on the brightness and light. The wrinkled areas can also be smoothed out with a scraper or disposable chopsticks for a less noticeable finish. View detail
Material:Carbon Style
Seat fabric is soft and the adhesive material is strong.
I was able to attach it perfectly.
Maybe it was a good thing I installed it on a mid-summer day.
In winter or when the temperature is low, it is easier to work with it if it is warmed up.
View detail
Expected
I tried to put my own sticker on Silencer, but it was not heat-resistant sticker, so it might melt.
So, as a result of my own consideration, I decided to put the KIJIMAHeat-resistant Sticker between the Silencer and the production Sticker to prevent heat.
I put a cut KIJIMAHeat-resistant Sticker on the Silencer and put the Sticker on top of it.
I've been driving it for a while now and there are no problems.
View detail
Cost, design, and manufacturer's products
I received it as soon as possible after ordering. Thank you very much. The color is the same as the KIJIMASticker, so I put it on the tank side. I love it. View detail
Graphic, shape and details are OK
Thank you for the fast delivery. I bought it as a design for my motorcycle. I haven't done any work on it yet, but I think it will stand out. View detail
It's going to stick.
The design is good for parenthesis and if you are a fan of KIJIMA, you will love Quantity!:1pc. is the sticker you want to have. View detail
Made by KIJIMA for your peace of mind
When I bought a Chinese Bracket before, it was deformed when I installed the Emblem and the vehicle vibration caused it to Emblem and Quantity:I bought it back as a set
It's a simple bracket, so it's a simple function, but it's not the only way to make it work The workmanship and accuracy is as expected of KIJIMA It is used with no problems at all
The difference in price is not so great, because cheap or bad is a waste of money in the end, and you can still feel safe Manufacturer's products are the best
View detail
easy to get rid of a wound
I bought it to cover the exhaust cover that was damaged when it fell in the strong wind
The unevenness of the parts and sticking them to the Slit part is up to the individual's skill, but it's not very obvious from a distance It was finished to a degree
It's difficult to reapply, so make a pattern of the part you want to apply and cut it to a little large texture I think it's a good idea to fold into the reverse side
View detail
It stuck on the Tank on Tank-back fixation. Although I thought that it was good at a clear Urethane sheet, since it was cut and put on the market in the small Size from Mr. KIJIMA, the die Knock sheet was stuck.Although it was a curved surface of the
It stuck on the Tank on Tank-back fixation.
Although I thought that it was good at a clear Urethane sheet, since it was cut and put on the market in the small Size from Mr. KIJIMA, the die Knock sheet was stuck.Although it was a curved surface of the Tank, it can stick finely and is satisfactory as a crack prevention sheet.
The remaining sheet is used when processing it in the style of a Carbon, crack hiding and.
View detail