Reviews
Effectiveness is good, glad I bought it.
[How is it used?
Exhaust System of Z900RS was replaced and Silencer was Bullet Silencer by K-FACTORY.
The kit came with two baffles, one for the outlet and one for the inlet, and the combination of the two was supposed to allow adjustment of volume and exhaust pressure.
When the outlet type was installed, it sounded like a large dump exhaust system and I could not bring myself to use it. The exhaust resistance of the inlet type was too large and the volume went down a little, but at mid-speed or higher, the exhaust clogged and the large width performance went down.
So, I thought there must be a way to lower the volume while maintaining a reasonable exhaust resistance, so I used this product.
Was the one you received as per Image?
As per Image as I had seen the actual product at the store.
Was the installation difficult?
There is no difficulty if you choose a Size that fits within the inside diameter of Silencer.
However, the Silencer exit diameter is 55Φ for use with Bullet Silencer,
The inside of the punching pipe had to be 45Φ so it was necessary to fill the 10mm gap at the exit.
I looked for a gasket that would fit, but could not find one, so I wrapped a heat-resistant aluminum tape around it.
Also, the Silencer fixing bolt that came with the kit was a retro black ordinary Hexagon bolt, so I used a silver cap bolt that I had on hand.
How was your experience with it?
The volume did not go down as much as I had hoped, but at the moment of startup without any Absolutely not!" The explosion was so loud that it felt like "I know it's annoying, but can you forgive Limit?" This was the Level that
Unlike the Silencer-attached baffle, the Straight structure is maintained, so exhaust resistance is not increased excessively, and the sound quality is not muddy and high-frequency components seem to be suppressed.
In terms of performance, it is not too much at low speeds, but it is not too much at high rpm, and it is not too much at high rpm.
However, the Bullet Silencer, which I almost gave up using because it was too noisy even though I like the look of Large, is now available, and the Silencer is also black and retractable, so it is unobtrusive and I am glad I purchased it.
[Included Parts:were they on?
None in particular
[Was there anything that disappointed you?
It would have been nice if the volume could have been a little lower, but then it would have been a poof clogging.
Once again, I felt that the OEM Exhaust System is well made.
View detail
Cosy! Sound deadening effect, of course.
[How is it used?
Used for cbr600rr. For muffling the sound of external Exhaust System.
Was the one you received as per Image?
Street Image
Was the installation difficult?
Drilling holes in the Pipe for installation was Large strange.
I am sure it is a Type that can only be attached to Exhaust End.
How was your experience with it?
It muffles the sound a bit, but it is still loud.
[Included Parts:were they on?
[Was there anything that disappointed you?
View detail
It's just that the volume will be lowered, but..
Motorcycle:KLX125
Exhaust System:OVER Stainless Steel Carbon Exhaust System
History
KLX125 OEMExhaust System sounds too small to notice the automobile I couldn't get it, so I changed it to the Full Exhaust System of OVER, and I had a dangerous experience rarr;End It became an annoying sound explosion even with Baffle, so Inner Consider purchasing a silencer
?attachment
Because the end shape of the Silencer is not straight, it is called the exhaust pipe and Mounted between Silencer
(It's only held in place by the momentum of the exhaust rather than mounting, so if you give it a shock, it will move )
Good points
The sound of the external exhaust system's single-cylinder sound, like a group of half-greater cylinders, is not too loud Became sound enough to Appeal the presence in the automobile
It's cost effective in terms of ensuring that the volume is reduced
Bad points
After about a month of use, I found out that the rust was on the large..
Stainless steel is still the best inner silencer
View detail
With silencing effect
Added to XL 1200 C SPORTSTER 1200 External Exhaust System.
Buy this item whose inner diameter is the closest.
The cotton part is hard and hard, it will silently sound.
Because the exhaust pressure of Motorcycle is high, cotton became a mosaumosa in a relatively short time.
Although it is not currently used, I think that it is effective when lowering the volume of Exhaust System at the time of vehicle inspection
View detail
It has an effect
I used it for the XL 1200 C SPORTSTER 1200 Exhaust System.
Exhaust System was a sharp exhaust sound near the straight pipe outside the company,
After installation, the sharpness of the sound calmed down, and it became a slightly muffled sound.
It is an impression that the sound is rounded.
I think that the volume was also suppressed and it was effective enough
View detail
Muffler effect perfectly
Since the Other Company Product Expression System of CRF 230 F was a bit of explosion to run on the public road, we installed the Inner silencer.
Because it is a Universal Product, we need some ingenuity, but the effect is outstanding.
It's not too quiet, it's too noisy.
I can recommend it..
View detail
"07 years Injection vehicle. I was annoyed by the badness of the throttle response of a normal muffler, and a feeling of excrement, and I decided on muffler exchange. I chose cycle shack of 2.5IN.(it was equipped with a same baffle as SE2) However ... sou
"07 years Injection vehicle. I was annoyed by the badness of the throttle response of a normal muffler, and a feeling of excrement, and I decided on muffler exchange. I chose cycle shack of 2.5IN.(it was equipped with a same baffle as SE2) However ... sound volume is so loud and I cannot start engine in the residential street at daytime and it is further embarrassment ... It was replaced in the press wool type. Although I cannot say it becomes quiet, I can realize a sound deadening effect certainly. It is the sound I can apply engine in the garden, (limited to daytime) and the depth, such as the large displacement vehicles do not go out there deep bass, one shot of the plosive is emphasized, and good feelings are increased. The throttle response was also finished on the perfect level. If it shifts to the higher gear at the time of a low speed, a little axel is opened and it is made feeling, a feeling of a beat and sound appropriate for a harley can be enjoyed fully." View detail
an auction -- the straight pipe short muffler purchase of a silencer-less one-off!! It equips and puffs an axel... it gets -- ~ being and purchasing an inner silencer by x. it is determination from a muffler inside diameter and the die length with whi
an auction -- the straight pipe short muffler purchase of a silencer-less one-off!! It equips and puffs an axel... it gets -- ~ being and purchasing an inner silencer by x.
it is determination from a muffler inside diameter and the die length with which it can equip to this product!! Attach immediately... CHITO -- since it is a we bit bad old man although it is noisy -- OK.
.
.
In order to unite with a muffler inside diameter when attaching, some processing is required, but a price is also handy and four stars.
View detail
Although it had equipped with the custom muffler almost near a straight pipe, the nuisance to the neighbors was considered and purchased. As operative, although it does not become precocious, it becomes abbreviation half [ of the state of a straight p
Although it had equipped with the custom muffler almost near a straight pipe, the nuisance to the neighbors was considered and purchased.
As operative, although it does not become precocious, it becomes abbreviation half [ of the state of a straight pipe ], and a high sound with sufficient normal in which tone quality also bursts disappears, and sound volume becomes crisp touch, and is large satisfaction.
It is the good touch which adjusts the grade sound volume which is the quantity of glass wool.
Muffler sound can be enjoyed now, without seldom caring about a nuisance to the neighbors.
However, about attachment, it was fairly troublesome.
Since this product is made more greatly about 1 mm than a notation size for exhaust leakage prevention, it does not enter, unless it will delete the outer circumference of a fixed portion, if an apt size is purchased.
Although I used the grinder, I think that it becomes fairly serious work in case of manual operation.
And since just it has worries about exhaust leakage when becoming distorted, the way which purchased the size smaller than a size needed from the beginning, and filled the crevice with the gasket may be comfort.
View detail