Reviews
Good manufacturing, as good as OEM.
It can be tightened with confidence.
It is well made, so let's tighten it up with a proper Band.
View detail
Repair of external Exhaust System.
The Band of Earls Gear's Slip-on Silencer that I bought used is not usable because the Screw does not turn in RustRust.
I checked and it was the same as this product.
The band itself is stainless steel, and the screws are iron, so Copa Coat is applied to the screw threads to prevent biting and rust.
It can be tightened normally and looks normal. No exhaust leaks, probably because it is evenly tightened.
I thought it was a good, safe product.
View detail
KIJIMA Stainless Steel Exhaust Band
I used to use a different band, but when I tightened it, the bolt diameter was a little thin and it was not strong enough.
After a certain amount of use, it was easy for the screws to be ruined by heat and tightening.
This Band has a slightly thicker Bolt and has no strength problems, so this Band is now used.
View detail
Used for Overhaul
It was used for Overhaul in conjunction with the disassembly of Silencer, which was suspect.
As described in the product description, the stinging when wrapping was kept to a minimum, and the work proceeded smoothly.
However, it is just hard to stick, but not totally impenetrable, so I think working quickly is HANG.
However, the work efficiency is a world of difference, so although it is a bit expensive, it is recommended.
View detail
Used for I.D. 60.5Φ.
63-68mmSize is used for Exhaust System with inner diameter of 60.5Φ.
Looking at the cost of Bolt's surplus, it would have been better if it had been a little smaller.
However, there is no problem at all in fixing it, so I am satisfied.
View detail
This is a standard component that seals the Well and Pipe together.
[How is it used?
Black dirt was dripping under the joint between the Chamber and Silencer, so I checked the packing and found a small amount of exhaust oil leaking out. 。 Packing was replaced about 6 years ago when the Chamber was cracked and replaced, so the surface was also cracked and had reached the end of its life span! 。 Still, it is amazing that there have been no problems for six years.
How was your experience with it?
I have been using it as a standard for some time and it is Just fit.
How did it compare to other products?
It is the one and only component that cannot be compared.
[Points to note]
Although Large is strong even when used in its original state, experience has shown that there are two key points to increase durability.
(1) Do not throw away the old part Clamp you removed, but use it (1 piece) 。 The new part has two Clamps at the front and rear ends of the packing, but by adding the Clamps from the old part to the center section, three Clamps can be used to secure the packing more securely and stably for a longer period of time.
2) Apply heat-resistant SiliconSealer to the joint of the Pipe (the part where it plugs in) and the entire inside of the Packing, and assemble. (If you are concerned about the appearance, wipe off any protrusion.)
Other items that would be helpful
Items to buy together:Silicon-based oil-resistantGasket Ultra CopperRTVSilicone
View detail
Material:Stainless Steel is good
I made a mistake with the size, but I think it is a very good product, Stainless Steel and it won't rust, and considering the burning thing, it is a Material:Stainless Steel exhaust pipe and silencer with band and material:Stainless Steel is a good choice. View detail
Used in SR400
Material:The exhaust pipe and silencer are made of Stainless Steel, so the color of the Plating Exhaust Band is different from the Plating Exhaust Band, but the Material:If the band is made of Stainless Steel, the burnt color will look natural. View detail
Toshi TECSilencer.
It fits Toshi TEC's Carbon silencer. The bore fits perfectly without any problem and without any need for fixing. I was able to restore the original quiet and light sound of the Titanium without any trouble since I could easily finish the prickling work just by trimming the length. Bean-jam-filled wafers in two pieces vertically (Monaka) The time and work required to push the material into the mold was reduced. The structure and material shape make it virtually impossible to push in the material. View detail
easy to get
When I installed YOSHIMURA's Slip-on Silencer, I am a stocky person, and I broke the attached Clamp band by holding the Torque wrench too tight for some reason, perhaps because of the installation angle.
It takes time, but I looked on the Net to order from YOSHIMURA and found that KIJIMA's products are identical to YOSHIMURA's.
It was easy to obtain and inexpensive.
View detail
I was concerned about the volume and hadn't replaced it in a long time.
Used for Silencer of AfterMarket's Exhaust System that is being replaced.
Silencer Full Length (Cylinder part) Used for 470mm, Silencer outer diameter 110mm, Inner pipe outer diameter 54mm.
Quantity of this item:1 pc. Min (500mm×1100mm) The guideline for the amount to be used in the "Punching pipe 54mm, 120φSilencer" was the same as that for the Wool, but the Wool was able to fit without excess. The total length could also be fit without any problem by lightly pushing it in.
As described in the description, it is in the shape of a seat and easy to wrap around inner pipe. I worked with bare hands, as it says it is non-scattering, and it was easy to work with, with almost no stinging pain characteristic of glass wool.
If durability is not a problem, I would use this product again next time.
View detail
Acoustafil is easy to handle and great!
It doesn't tingle, it doesn't fly around, is it really Glass Wool?
It is so easy to handle that
I used protective Glasses, Mask and Vinyl gloves just in case, but I didn't need them!
However, when cut, fiber ends will come out, and if this happens, it is no different from regular Glass Wool. Be careful to cut as little as possible.
The price is much higher than other products, but the ease of handling is unmatched, so I think the cost performance is high.
I will definitely use Acoustafil again next time!
View detail
It was as advertised.
The original was Steel wool and Glass Wool, but only Glass Wool was available for vehicle inspection.
The heat from the exhaust air caused it to expand, so we didn't have to be too careful with the wrapping method to muffle the sound, and there was no stinging after the work was done.
There is also a quantity for two times.
View detail
Used for external Muffler baffle
[How is it used?
External Exhaust SystemSlip-on Silencer was used because of its explosive sound.
Was the one you received as per Image?
BaffleExactlySize is not available, so it is processed and used
Was the installation difficult?
It was a little difficult because of the special Baffle shape.
How was your experience with it?
Volume dropped moderately.
[Included Parts:were they on?
With Wire for fixing
[Was there anything that disappointed you?
I wanted more Wire.
The excess was sealed with zip-lock to prevent shattering.
View detail
Silencer Fixed
I purchased this product for my car car Silencer-less Toa. It works fine. It can be fixed tightly. View detail
Spring is well made and reliable!
This product is very well made and reliable, and the fact that it is scratch resistant even when gripped by radio pliers is also a high point! View detail
Quality ○○
I only used Rubber because Band did not fit. I did not use it, but the quality of the Band itself was solid. View detail
I'm happy with the low sound it makes while driving.
I chose the Polish end because I like the Silver Heat Guard?Exhaust End?Side plate, which is the Accent of the BOLT Shoulder Bag's appearance.
As for the sound, because it is Japanese Vehicle Inspection Correspondence, it is not the explosive sound like the illegal exhaust system, but it becomes large and low and thicker than NORMAL, and it becomes the large sound which can be heard through the helmet all the time while running. It became a large sound that can be heard through the helmet all the time while running.
The driving, fuel consumption, etc. are almost the same.
I am satisfied with this exhaust system because it is American motorcycle exhaust system which is more concerned with appearance and sound than running.
The installation can be done in about 30 minutes by an amateur if you follow the instruction manual.
Quantity of L-TypeHexagonal Wrench:Set (for removing various Bolts) and a 22mm Glasses Wrench (for removing the O2 Sensor) are all you need to replace it.
View detail
Used for 60mmSize Silencer
[How is it used?
I used it to fix the external Silencer on my TZr50R.
Silencer is 60mm, but I bought 70mm and Band because I saw that there is a gap at the Bolt fixing point when I put Elastic band.
Was the one you received as per Image?
It's hard to tell because there's no explanation, but as you can see in the picture, it comes with the BandBody and a set of bolts for installation.
There is no BALIetc. and it can be used as it is.
Was the installation difficult?
KIJIMA for Silencer heat resistant Elastic band (https://www.webike.net/sd/1033907/) I used a 60mm Silencer, but it is a bit oval and there is a little gap between the two.
Originally, even if it is not fixed, it is attached rather firmly and is a supplementary fixation, so it is enough for me personally.
How was your experience with it?
Originally, the previous owner also seemed to run without fixing, and there was no particular problem in running, but the sense of security increased.
Also, I personally like the way it looks better fixed, so I'm happy with it.
How did it compare to other products?
Compared with other Silencer band etc., it is inexpensive and the SizeLineup is abundant.
However, I thought that it would be better if there was a middle lineup of 65mmetc. for using Elastic band.
【Review】
This Silencer band is inexpensive but comes with a Bolt and is ready to use.
As long as it doesn't fall over, I don't think there will be any problems with durability.
View detail
This for KIJIMA's Silencer band!
[How is it used?
I used it to fix the external Silencer on my TZr50R.
KIJIMA's Silencer band70?Size (https://www.webike.net/sd/20522931/) It is used by wrapping it around the inside of the
How was your experience with it?
It was long enough for a 60mm Silencer.
I used it for KIJIMA's Silencer band, so the width is made with a good size feeling.
The width of your silencer band may be a little too wide, so please check the width of your silencer band.
How did it compare to other products?
The heat resistant Elastic band for Silencer is not so Single Body. (Other than that, KITACO has it out.) I used it for the silencer band of KIJIMA, so I added the manufacturer.
Naturally, I'm happy with the result because it's made in just the right width and looks great.
[Points to note]
As stated, the width may be a bit long depending on the Silencer.
KITACO Band (https://www.webike.net/sd/1343195/) is 25mm wide, so it is necessary to consider with that.
【Review】
The size is just right to use with KIJIMA's Silencer band.
The thickness of the Elastic band of KITACO can be selected, so I thought it would be better if the thickness of the KIJIMA one can be selected as well.
View detail