Reviews
GOOD GOOD Glass Wool Acoustafil
Cutting is accurate and no cutetc. is required.
The Glass fibers are braided and compressed thinly, so there is virtually no scuffing of the Glass fibers.
(but protective equipment is still required)
The compressed Seat is temporarily fixed with Tape and expands with heat after assembly.
The work of putting it in the tube is easy.
The purchase cost is usually a problem instead of the difficulty of the work being reduced compared to Glass Wool.
Silencer parts removal & disassembly, Rivet removal by Drill,
Rivet re-fixing, hole alignment, and removal of remaining gasketetc. using special tools,
Parts matching checks and other su-kills are necessary.
One 1100mm-long Seat is equivalent to one Silencer.
Two Silencers would require two pairs.
View detail
Effectiveness is good, glad I bought it.
[How is it used?
Exhaust System of Z900RS was replaced and Silencer was Bullet Silencer by K-FACTORY.
The kit came with two baffles, one for the outlet and one for the inlet, and the combination of the two was supposed to allow adjustment of volume and exhaust pressure.
When the outlet type was installed, it sounded like a large dump exhaust system and I could not bring myself to use it. The exhaust resistance of the inlet type was too large and the volume went down a little, but at mid-speed or higher, the exhaust clogged and the large width performance went down.
So, I thought there must be a way to lower the volume while maintaining a reasonable exhaust resistance, so I used this product.
Was the one you received as per Image?
As per Image as I had seen the actual product at the store.
Was the installation difficult?
There is no difficulty if you choose a Size that fits within the inside diameter of Silencer.
However, the Silencer exit diameter is 55Φ for use with Bullet Silencer,
The inside of the punching pipe had to be 45Φ so it was necessary to fill the 10mm gap at the exit.
I looked for a gasket that would fit, but could not find one, so I wrapped a heat-resistant aluminum tape around it.
Also, the Silencer fixing bolt that came with the kit was a retro black ordinary Hexagon bolt, so I used a silver cap bolt that I had on hand.
How was your experience with it?
The volume did not go down as much as I had hoped, but at the moment of startup without any Absolutely not!" The explosion was so loud that it felt like "I know it's annoying, but can you forgive Limit?" This was the Level that
Unlike the Silencer-attached baffle, the Straight structure is maintained, so exhaust resistance is not increased excessively, and the sound quality is not muddy and high-frequency components seem to be suppressed.
In terms of performance, it is not too much at low speeds, but it is not too much at high rpm, and it is not too much at high rpm.
However, the Bullet Silencer, which I almost gave up using because it was too noisy even though I like the look of Large, is now available, and the Silencer is also black and retractable, so it is unobtrusive and I am glad I purchased it.
[Included Parts:were they on?
None in particular
[Was there anything that disappointed you?
It would have been nice if the volume could have been a little lower, but then it would have been a poof clogging.
Once again, I felt that the OEM Exhaust System is well made.
View detail
Decent Exhaust Spring
Used for external exhaust system of GSX1300R GSX1300R HAYABUSA
When the exhaust system was replaced with an external exhaust system, the chatter sound of the Gold genus became more loud when the RPM was raised, so it was introduced as a countermeasure against resonance/interference noise.
This product is a type of spring whose Hook rotates freely, just like the springs that come standard with AKRAPOVIC and YOSHIMURA.
It also comes with a Rubber for sound control.
(Although it is shiny and the texture is not so good.)
It seems to have good heat resistance for normal use, but if it is pressed against Cowl or other parts and directly hits the exhaust pipe, it will melt, so care is required.
The spring itself is SUS with a relatively large wire diameter, so it can be tensioned firmly and is rust-resistant and solid.
The Spring is generally as it looks, but one thing to note is the installation length.
Size100mm" means the free length is 100mm.
Note that Tension is not applied unless it is used with some extension.
As per Q&A, it seems that the mounting length is intended to be 120mm.
I tried to install it, but it was a little loose, so I went with the company's M size. (85mm) I bought a new one.
Neck would be the price.
I understand that it is a solid product, but it is a little expensive.
A 4-cylinder Full Exhaust System uses more than 10 springs depending on the type, so the spring alone will cost more than 10,000 yen.
It's a little tough, as you'd expect.
However, the product is solid, and from a quick search, it seems that this size cannot be diverted from AKRAPOVIC or YOSHIMURA's Repair products, so it would be the best solution for those who seek quality over cost.
View detail
After changing from COBRA's Exhaust System, it became dramatically easier to ride.
When I was driving a YamahaBolt and replaced the COBRA Exhaust System with the KIJIMA Exhaust System, I felt how much easier it was to ride.
The sound of KIJIMA's Exhaust System is a little insufficient because of the Japanese Vehicle Inspection Correspondence.
I like the Design, so I am satisfied.
View detail
It is quite solidly made!
[How is it used?
We needed the Exhaust Band when we replaced the Short Exhaust System, so we decided to purchase it.
Was the one you received as per Image?
Material:Being Aluminum, I was concerned about the quality, but I was glad to see that it was more solidly made than Image.
Was the installation difficult?
Simply fit the Silencer.
How was your experience with it?
It was wide and solid, so I felt secure.
Aluminum silencer has Material:Material than Stainless Steel:I think the Silencer band in Aluminum would look better.
[Included Parts:were they on?
Material:It came with a Stainless Steel Bolt and Nut.
[Was there anything that disappointed you?
Not at all. Some people may want anti-vibration Rubber.
I would have appreciated an intermediate diameter of 65mm, as the ▼Size range is 60mm in diameter followed by 70mm in diameter.
View detail
Cosy! Sound deadening effect, of course.
[How is it used?
Used for cbr600rr. For muffling the sound of external Exhaust System.
Was the one you received as per Image?
Street Image
Was the installation difficult?
Drilling holes in the Pipe for installation was Large strange.
I am sure it is a Type that can only be attached to Exhaust End.
How was your experience with it?
It muffles the sound a bit, but it is still loud.
[Included Parts:were they on?
[Was there anything that disappointed you?
View detail
I bought it as a spare.
I bought this as a spare for the Exhaust System that came with it.
I think this one is easier to use.
View detail
Since it is a rubber commodity, the crack of the absorption silencer of a certain amount of vibration is not attached easily.
Since it is a rubber commodity, the crack of the absorption silencer of a certain amount of vibration is not attached easily. View detail
It was Exactly for Repair of CB1100Normal muffler!
Normal mufflerBand was ruined by Rust, so I replaced it. The price is low, so it helps.
This product has a Band section with Material:The screw is made of Stainless Steel, so its strength and durability are assured.
View detail
The Bolt is Steel, which is −?
When I replaced the Silencer with Other Brand Product, the Bolt of the attached Band that tightens the Exhaust pipe and Silencer was too long.
The Band is made of Stainless Steel, but the Bolt is made of Steel.
View detail
Mostly OK.
It is used for the Joint of Slip-on Silencer.
I have purchased and am using it because it is wider and can be hung more tightening torque than the OEM.
If you want to say it, I think the follow-up performance will be 100% if you don't have the R-shaped inner gold part of the Bolt tightening part.
View detail
Well, that's about it.
I used it to replace Silencer's Glass Wool.
This item comes with Glass Wool and Steel Wool so it can be rolled in layers.
But because I put it on the Smallish Exhaust System, it was quite crispy.
It's like I was forced to push it in.
The volume felt spread out and cohesive.
It's a consumable product and needs to be replaced regularly.
View detail
It's just that the volume will be lowered, but..
Motorcycle：KLX125
Exhaust System：OVER Stainless Steel Carbon Exhaust System
History
KLX125 OEMExhaust System sounds too small to notice the automobile I couldn't get it, so I changed it to the Full Exhaust System of OVER, and I had a dangerous experience rarr;End It became an annoying sound explosion even with Baffle, so Inner Consider purchasing a silencer
?attachment
Because the end shape of the Silencer is not straight, it is called the exhaust pipe and Mounted between Silencer
(It's only held in place by the momentum of the exhaust rather than mounting, so if you give it a shock, it will move )
Good points
The sound of the external exhaust system's single-cylinder sound, like a group of half-greater cylinders, is not too loud Became sound enough to Appeal the presence in the automobile
It's cost effective in terms of ensuring that the volume is reduced
Bad points
After about a month of use, I found out that the rust was on the large..
Stainless steel is still the best inner silencer
View detail
Perfect fit
The ChamberSilencer's size is 60 pies and thin, so it wasn't easy to find it on the market But I bought it as soon as I found it, and I found a DIY bracket to fit it visually, and it fit nicely It's done It's a question of how long it can withstand vibration, but it's much better than no vibration We're going View detail
The size isn't great
I couldn't identify the manufacturer of the Silencer Bracket, so The width does not match, so I cut it and forced it to fit I don't think so, but it's a bit of a shame View detail
4.0
When I changed Shaffle's Baffle, I used this product because it was an explosion. The effect was absolutely Large, and it turned into an elegant sound quality. If the attached needle gold is a little longer it is none to say. View detail
With silencing effect
Added to XL 1200 C SPORTSTER 1200 External Exhaust System.
Buy this item whose inner diameter is the closest.
The cotton part is hard and hard, it will silently sound.
Because the exhaust pressure of Motorcycle is high, cotton became a mosaumosa in a relatively short time.
Although it is not currently used, I think that it is effective when lowering the volume of Exhaust System at the time of vehicle inspection
View detail
Useable.
MONKEY I installed the Exhaust System outside the place I got more than I expected volume, so in the Silencer Exhaust pipe Space in the back of the plugging part, rounded StainlessPunching metal Wrapped Steel wool, Glass Wool around the outside Stainless Steel Wire and fixed it.
Because it is dislike when it comes to resistance, Punching metal wound Large more than the inner diameter of Exhaust pipe.
The sound is suppressed throughout the whole area, plosive sounds in the middle and high speed areas that I was particularly concerned have disappeared considerably Large satisfaction.
Stainless's Steel wool is saved because it is not placed in the home center etc..
Although I do not know about durability yet, as I did with another vehicle type the same way before, I did not scatter more than 4000 km, probably Large durable?
I will check if the sound becomes loud.
View detail
It has an effect
I used it for the XL 1200 C SPORTSTER 1200 Exhaust System.
Exhaust System was a sharp exhaust sound near the straight pipe outside the company,
After installation, the sharpness of the sound calmed down, and it became a slightly muffled sound.
It is an impression that the sound is rounded.
I think that the volume was also suppressed and it was effective enough
View detail
I had some trouble with the installation
It is JMCA Correspondence. It increases the volume even by saying. Bass is also good.
For example, it looks like Ducati type.
Harley is not like Crank angle and Stroke difference. First impression.
Although it is cSpecifications, removing the OEM was easy. However, it was hard for me to replace it..
Screw Hole accuracy is too good? Watarase exhaust system Rear station (Bolt 2 points close to Rear brake)
Do not match well with.
I managed to stop losing Bolt when I managed to stop it.
Bolt stopped being stopped half way through. Do it again (Lol)
Also, Right feet Heat Guard (Double) It is supposed to divert OEM.
at first (Inner Bolt 3 points) I will put on first.
second (Outer Silver) Slide it in the gap of the footpeg after fixing the Exhaust System.
Such as. Just after installation there is almost no gap between footpeg and Guard.
It might be impossible if there is a design error.
Maintaining NORMAL in terms of performance. Full throttle may not be different Motorcycle.
View detail