Reviews
Good manufacturing, as good as OEM.
It can be tightened with confidence.
It is well made, so let's tighten it up with a proper Band.
View detail
Fits: HONDA gorilla (Gorilla spp., esp. western gorilla, Gorilla gorilla), HONDA monkey
Partially made of Steel, it is prone to rust.
[How is it used?
The Normal pedal was a bit tasteless, so it was attached to the Brake pedal version up.
Was the one you received as per Image?
The size was larger than expected and easy to step on.
Was the installation difficult?
Install the Normal brake pedal so that it is sandwiched between the Normal brake pedal.
Plus screw allows installation with a single Driver.
How was your experience with it?
The driving operation is easier because there is more area to step on.
However, it took some time to get used to it because of the slight increase in height.
[Included Parts:were they on?
Mounting Screws, Mounting Hardware, etc.
[Was there anything that disappointed you?
Body is Material:Aluminum, but the Plus screw and the bracket on the reverse side are rusted with steel. Especially when the Plus screw is rusted, it is difficult to remove it.
▼This is a common design, but you can enjoy a slightly Mischief atmosphere.
I think the discomfort during operation depends on the person.
View detail
Fits: HONDA DAX125, HONDA MONKEY125
Is it essential in modern times?
Good product
When you live a life where your phone is indispensable, battery is always a concern.
The USB port gives me a sense of security.
If you read the Instruction Manual carefully, I think it is gentle as a work S-Kill.
However, it is necessary to pay attention to the removal and installation of the light cover (plating parts) and the fit of the wiring.
View detail
I put it on as a spare.
External Fuel filter attached to ESTRELLA.
It has been immobile for a while, and you can often find a little bit of age-related deterioration in various parts of the car. 。
There does not appear to be any fuel seepage, especially in the Fuel Cock area, but there is no denying that the Fuel Cock has deteriorated over time.
The other day, I was worried about the rust in the fuel tank, and although I have removed rust to prevent impurities from entering Gasoline, I am not sure about it, so I will install an additional external type of fuel filter.
Fuel filter
A filter device used in automobiles to filter fine impurities contained in fuel.
It is used for the purpose of removing water, sand, and dust mixed in during refueling, etc., and maintaining sufficient fuel efficiency.
There seems to be a time for replacement, though not up to the air filter.
■ 50,000 km at Carburetor Vehicles
■Injection car with 100,000 km
■Diesel car with 50,000 km
is the standard.
Continued use of the filter past its replacement time will not only clog the fuel filter element and cause a lack of engine output, but will also cause the filter to lose its original function of capturing foreign matter and separating moisture.
[When the fuel filter clogs.
‥
Idling of ▲Engine is unstable.
Engine seems to stop when driving.
▲ Suddenly, Engine stopped spewing.
Failure to start = Engine will not start.
I haven't experienced the clogging of the Filter yet, but considering the distance and age, it should be replaced. 。
In my 90's ESTRELLA, the fuel filter is integrated with the fuel cock and inserted into the tank. That is not so bad, but I wanted to be sure.
I also added an external Type as a spare.
I chose KIJIMA's because it was inexpensive and I had used it before.
The deciding factor was the transparency, which makes it easy to see dirt.
Replacement procedure.
(1) Fuel Cock is turned off
↓
(2) To be sure, Gasoline in the carburetor should also be removed.
↓
(3) Interrupt the fuel filter between the rubber hose connecting the fuel cock and the carburetor.
It is wise to prepare Oil Resistant Hose separately because OEM Hose is not long enough.
↓
(4) Turn on Cook and apply Engine.
Operation check.
Fuel Cock flows by Engine pressure.
after replacement
No problems
They seem to be getting rid of the impurities for sure.
Durability...? I think Large is durable because it is inexpensive and will be replaced with a con stunt.
It is a good idea to have insurance on older Motorcycles.
Installation is also easy.
View detail
Fits: BMW R1200GS, BMW R1200GS Adventure, BMW R1200R, BMW R1200RS, BMW R1200RT, BMW R1250GS, BMW R1250GS Adventure, BMW R1250R, BMW R1250RS, BMW R1250RT
It's a must for Oil replacement.
BMW is said to be a Motorcycle only for the rich, but I still want to put in my favorite Oil and keep the cost down.
The only thing I decided to ask Dealer for was the price, and the price is meta-fucking-high.
So I changed the Oil by myself!
Attachment, too!
This is essential in that case!
View detail
Fits: KAWASAKI Ninja 250, KAWASAKI Ninja 400 (2014-)
Cospa strongest
OEMRear Fender was so creepy that I decided to convert it to a Fender Eliminator, because the Kit is cheap, the License Plate looks like it grows directly from the Motorcycle, and there is a Loading Hook. (In Z400, removing the OEMRear Fender means losing the Loading Hook.) The fact that you can use an OEMBlinker is also Gold-friendly.
KIJIMA's description claims that it is for NINJA400 and NINJA2 Helmet50R, and does not mention a single word about my beloved Z400, but this Quantity:I bought this one because I saw some guys on the Internet who installed Set on their Z400, and the back of Z400 is almost the same as the current NINJA400.
The Kit itself is carefully processed and absorbent to the touch. I thought I got my money's worth at this stage. The installation instruction manual is also very detailed and easy to understand. The hardest part of the installation was the removal and installation of the blinker and the coupler of the license lamp, and the porting of the OEMB blinker. I cut off the rubber cover around the Coupler and solved the Blinker by my own efforts. All of them are Kawasaki's fault, not KIJIMA's. Kawasaki designed the blinker with poor maintainability. What is going on with Kawasaki?
The Loading Hook is also very useful and in a very good position. It is a great product that makes me feel like a fool to buy a kit around 20,000 yen for the same purpose when such a great kit is available.
View detail
Fits: SUZUKI GIXXERSF 250, SUZUKI GIXXER 250, SUZUKI GIXXER150, SUZUKI GSX-R125, SUZUKI GSX-S125, SUZUKI BURGMAN 400
You should change the cheap ones often.
This is a reasonably priced Filter for a 2012 KTM DUKE200. If you are a normal rider, it is better to change the cheap one frequently than to buy an expensive Filter and use it persistently.ОRing should be changed once in a while, and at that time you should use Quantity:Buy Set's stuff!
Motorcycles that have been run a lot do not have gold dust, so it is enough without magnet.
The replacement procedure assumes that the Oil is drained.
Remove the lid of ?Filter. 8mmWrench
?This time we will use the lid side and the back ОRing.
Remove the filter and tighten the Bolt on the lid to finish. After replacing the filter, run it for a while to check for leaks.
By the way, the cheap ones seem to have large filter holes. The cheap ones may have oil leaking out from the gap, not into the filter but into the inside of the filter.
View detail
Moped Plate
It is easy to install.I just installed it,
How durable is the Sticker?
View detail
Exactly to the OVER baxter!
Rubber Only replacement is available at a lower price than OVER's Kit. View detail
DL1000 V-STROM800 used for power extraction under Seat
The DL1000 V-STROM800 has an OEMOption to install a 12VCigar lighter socket under the Rear Sets. The Attachment power supply Wiring for this purpose comes to the position shown in the photo. If you use KIJIMA's ACC Branch Harness that you purchased, you can get the power supply in Couplet-on. However, please note that the +- terminals are reversed, so the terminals need to be replaced. This is recommended for those who do not want to damage the existing Wiring. View detail
It is easy to install.!!
Anyone can easily install it.
I am satisfied with the shape as expected.
The color would have been much better if it had been matte….
It's looking good.
View detail
ITType." What does that mean, Italy?
I wanted to change to a Tail lamp with an integrated License Plate Light. I could have chosen anything, but since the car I was installing it on is an old ItalianRacer, I looked for a design that would not ruin the atmosphere and decided on this one.
I think KIJIMA is the best because the valve is sold separately, but it is a product of a well-known manufacturer, inexpensive, and easily available, and KIJIMA also supplies small repair parts such as lenses and rubber base parts. KIJIMA and Tail lamps are strong for classic vehicles.
Personally, I am disappointed only in the Fixing Screw, which is too small, and the Nut and Washer are too small to work with, and the originally drilled holes are too large in diameter. If you are going to drill a hole in a cowl, I don't think M3 or M5 will make any difference.
The base of the Rubber has a fairly solid thickness, and these points are very favorable.
Although there are only three wings, a WiringMemo is included, and it is also designed with the beginner in mind.
View detail
Fits: HUSQVARNA SVARTPILEN 401, HUSQVARNA VITPILEN 401, HUSQVARNA SVARTPILEN 200, HUSQVARNA SVARTPILEN 125, HUSQVARNA SVARTPILEN 250
The best choice for waterproof bag storage
It was useful during long distance tours.
Since the rear seat of the Svartpilen is short and narrow, this carrier can stably hold a waterproof bag of about 40 liters.
The design is simple, so it doesn't look too distracting.
Both 1st and 2nd generation fillens can be used. -------------------------------------------------- -------- It was useful during long distance tours. Since the rear seat of the Svartpilen is short and narrow, this carrier can stably hold a waterproof bag of about 40 liters. The design is simple, so it doesn't look too distracting. Both 1st and 2nd generation fillens can be used. Powered by Google Translator
View detail
tw200
The appearance has been improved by the Large change,
The instruction manual was easy to understand and I had no trouble installing it.
View detail
Fits: HONDA REBEL500, HONDA REBEL250SEdition, HONDA REBEL250
KIJIMAFrontReachSeat
I used to ride with a GelCushion, but it used to be a hassle with gapping, etc. The Cushion is no longer necessary, and the seating has become more comfortable.
Regarding the installation, there is too much play in the claws that insert into the body, so some modification is necessary, such as covering the claws with rubber material. I would like you to improve this part.
View detail
Insistence is strong
The bar is quite high and has a strong presence.
The color and texture are nice.
View detail
a perfect fit for a bike
very precise and sparkly It's easy to wear It would be nice if the prescribed torque value for the fastening bolt was written. The combination with "overracing subframe" is good My bike has become a little more shiny. View detail
GOOD GOOD Glass Wool Acoustafil
Cutting is accurate and no cutetc. is required.
The Glass fibers are braided and compressed thinly, so there is virtually no scuffing of the Glass fibers.
(but protective equipment is still required)
The compressed Seat is temporarily fixed with Tape and expands with heat after assembly.
The work of putting it in the tube is easy.
The purchase cost is usually a problem instead of the difficulty of the work being reduced compared to Glass Wool.
Silencer parts removal & disassembly, Rivet removal by Drill,
Rivet re-fixing, hole alignment, and removal of remaining gasketetc. using special tools,
Parts matching checks and other su-kills are necessary.
One 1100mm-long Seat is equivalent to one Silencer.
Two Silencers would require two pairs.
View detail
Repair of external Exhaust System.
The Band of Earls Gear's Slip-on Silencer that I bought used is not usable because the Screw does not turn in RustRust.
I checked and it was the same as this product.
The band itself is stainless steel, and the screws are iron, so Copa Coat is applied to the screw threads to prevent biting and rust.
It can be tightened normally and looks normal. No exhaust leaks, probably because it is evenly tightened.
I thought it was a good, safe product.
View detail
Good
If you read the manual, it is easy to install and fits well. It weighs more than you think. The cooling fins have a nice shape. View detail