Reviews
It's convenient to use without any problems.
The only complaint was the startup time, but this has been improved with the May 2024 Up date.
The screen is easy to read, and there are no problems operating it with the Gloves on.
Merit is more Large-like, which allows you to control Navigation and music without leaving your phone in the Bag, than the fact that you can no longer control your phone in Insta360.
View detail
For my first SMARTRideMonitor.
I installed it because the slight vibration of the Motorcycle was affecting the Camera function of my phone (iPhone11Pro).
We wanted to keep Wiring simple, so we chose the Type without the drareco function.
The kit comes with a variety of brackets for installation, so I think it can be used on most large vehicles. I used the base of the RAM Mount that I originally used, so I was able to install it without any extra work.
Wiring is only required to connect to the Plus and Minus terminals of the battery and to the ACC power supply.
Both WiFi and Bluetooth connect without any problems or glitches.
It is not particularly difficult to see even under bright sunlight during the day. I expect that it will be visible even in the midsummer sun.
The downside is that other WiFi-based devices will not work. I tried to remotely control my insta360 from my phone and couldn't do it.
As a supplement, when you register as a User, you will be directed to a dedicated line for inquiries and they will respond to your detailed questions. I was lost in Wiring myself, but they were very polite and helpful.
View detail
STREET TRIPLE2023 KDR-D21 installation
I had already installed it on March 16,
This is an Impression after using it for a while and doing various settings since it did not come with a proper Instruction Manual.
First of all, installation is a simple matter of connecting the Attachment power supply, Battery power supply, and Earth.
If you know how to get power, you can DIY it. The other thing to do is to install Wiring.
In this respect, it would be good without the Instruction Manual.
It is a Camera, but I like the fact that the length of the Wiring is different for the rear and the front. However,
Why are the terminals at the connection points the same color! I don't know which way to connect...
Also, as others have mentioned, the Cap for the Air Pressure Sensor had the F and R reversed. Also, I had to disconnect the battery and reconnect it to connect to the Body.
Well, so far, it's the usual Trouble in doing DIY, so I'll leave it at that.
I'd rather have nothing. What? Nothing?" I think.
From here on, it is a feeling of use. However, since there is no Instruction Manual, it is difficult to set up the system.
Touch panel is a bit dull. I guess this area can't be helped because of the low price.
I am an iPhone and it is CARPLAY, but it takes a long time to connect.
Do you want to connect to CARPLAY 60 seconds after turning it on? appears about 2 times after turning on the power.
I can't wait, so I'm running slowly and warming up until the connection is made.
As for the connection, it's like this, so if you CHOINORI and turn the key Off
It is a hassle to reconnect each time.
The Touch panel is dull, so smooth navigation is possible when using the iPhone to search for routes.
I feel like my iPhone battery runs out faster since I started connecting to this.
All of these electrical systems are the same, but the length of the connection terminals coming out of the Body is the same.
If the terminal part is the same length, only the terminal part will swell up when it is put together...
If possible, I would like them to be connected with one wire because they are bulky, or if there are four wires coming out, I would like them to have two different lengths for each wire.
Finally, the
The good part
No need to worry about battery level since it is connected to the vehicle.
I heard that people who connect to Income can operate it by voice,
It can be operated without using the Touch panel. (I do not use Income).
This price includes Air Pressure Sensor and Front and Rear Camera.
The bad part
The iPhone battery runs out fast. (I think this is the same with all machines)
Touch panel is dull.
No Instruction Manual.
BallMount, so lower Quantity:Cannot Set. (I used SP CONNECTO)
The hardness of the Camera's feet makes it difficult to wear on round surfaces.
Is this how it is?
Frankly, I don't recommend this for those who already have a driver's license.
The price is low, so it is good for new installations.
View detail
I am satisfied with it, but there are some points that may bother some people.
I purchased the initial lot and installed it on the same day, and use it every weekend for day-touring. I originally used a smartphone Holder, but found the following points inconvenient, so I purchased this SMARTMonitor.
It is a hassle to take the phone on and off every time you get in and out of the car, especially when you stop for a short while at a convenience store.
It can't be used in the rain (it's a notebook case, so it gets wet, and USB charging from Motorcycle is likely to be shorted).
・Heat makes the phone behave strangely during extreme heat.
The phone holder that can be mounted even in a pocketbook case is too bulky and cluttered around the handlebar.
When a phone call comes in while driving, the Sleep screen appears and Navigation cannot be viewed.
The proportion of parts that are not functions of the product itself (DFS for the application of the Radio Law (60-second wait for connection), Android Auto's characteristics, and performance) is large, but I will write my impressions when I put them together and consider them as a single product.
Elimination of inconvenience points
I→m still not sure how it behaves in extreme heat, but I have almost eliminated it.
Comfort of use
→ no problem but with the following caveats
Points to note
Touch with→Gloves is not very responsive, so Touch pan is required (or TradeOff, since it didn't malfunction even with considerable rain?)
→Brightness switching may be dependent on the phone side, or it may be set to nighttime MODE even in the daytime, or daytime MODE even in the middle of the night.
→After DFS is completed, it takes a long time to connect to my phone. after DFS is completed, it goes to WiFi connection, but it connects after repeating device search, Home screen, device search 2 or 3 times (1 or 2 minutes during this time). is it compatible with my phone?
→ The screen rendering is choppy. I don't use it for Video or Game, so it doesn't affect my use, but if you're used to the slippery crispness of a smartphone, that? If you are used to the smoothness and crispness of a smartphone, you may think, "What the hell?
→And Lloyd Auto is limited in what it can do due to many restrictions.
If you don't check it beforehand, you may be surprised at how little you can do if you use it like MirrorRingMonitor on your smartphone.
Overall, I am satisfied with the price because I was able to solve the inconvenience I had expected at this price, but I think I might have been disappointed if I had purchased the product without much research.
View detail
Cospa best
It is easy to lock and the mounting strength is Firmly fixed, unmatched by other companies. View detail
Smartphone Holder KaEdia
This Holder can be easily attached with the included Hexagonal Wrench. It has an Attachment for any Motorcycle. It is very easy to operate and you can fix and remove the phone with one hand. I am very satisfied with it. View detail
Not usable, even COMPRyans in Manufacturer?
First of all, use iPhone for Navigation in Touring, Camera and other corruptions. (Mechanical anti-shake rather old iPhone) of
Purchased this product considering the possibility.
Image was purchased with the intention of being able to use Navigation on the iPhone instead of the Goo GRUMap and other devices.
First of all, as for the product packaging, etc., it is cheap with a Chinese flavor, the inner box with foil stamping but PeLePera, and the outer box is also difficult to understand the product description (This is true for HP as well.)
The quality of the product body is as follows:First of all, two LCD protective films are attached to the body.
The one with the Manufacturer logo is easily recognizable, but there is another one pasted below it.
Also, this QUALITY must be low.
It is very dusty in new condition and looks like a protective film on a smartphone that has been applied in a messy manner.
There are no instructions on how to install anti-theft brackets, etc. The Instruction Manual is almost completely silent, explaining only that you can use it by connecting ACC, Plus, and Earth.
So, what are my impressions of Body's use?
First, the screen size should be measured in advance.
The body size is almost the same as that of the iPhone 14, but like the old LCD Monitor, the bezel portion of the screen is large, so the display portion is much smaller than the body. (Design that feels old-fashioned)
It is also very thick. It is about the thickness of 2.3 cell phones stacked on top of each other, making it very bulky.
And when you use it. First, the Touch panel Response is
It's slow as shit.
It is useless. It's so bad that you can't operate it while driving, but it doesn't make you think about it.
I made the mistake of thinking it was going to be the same as an iPhone that costs about 150,000, but it's soooo bad.
And even if I operate it with my bare hands, it taps on different parts of the board.
Cheesy electronic sounds and Manufacturer logo displayed when powered on
No, you are not such a proud Manufacturer, Small one hour to see if you can't turn it off.
The most discouraging thing about this is that it doesn't connect to my phone very well.
And, due to the radio wave law, the connection cannot be established for 60 seconds after startup.
Now, do you leave your motorcycle in place for 60 seconds after starting the engine each time?
Is your neighborhood Large sturdy?
Or do I leave the Headlight on for 60 seconds without applying Engine?
Is BatteryLarge sturdy?
I contacted the Manufacturer about this.
It's on the website. (W52 indoor /W56 outdoor only; it does not say that it cannot be used for 60 seconds. Are you telling me to check the radio laws myself?)
If you make a W52, you don't have to wait. But it's illegal, so use your own judgment and do something illegal.
Huh, the Manufacturer recommends illegal activities to the User?
I bought it because it was reasonably priced and had just been released.
The website and product descriptions are appropriate. Packaging, quality control, and after sales are all appropriate and pokey.
This is the first time I have purchased from a Manufacturer, but I would not recommend a Manufacturer that is not well-known.
It's been a long time since I've had a chance to make an impression since the sale of the property was successfully finalized.
I wish that one less person would buy this product.
View detail
KaEdia is still good!
Although many companies have released SMARTMonitor, I have been waiting for CaEdia's product. I have been waiting for a product from CaEdia because, after all, it is the most cost-effective. I have purchased many of KaEdia's products and knew their high quality and high cost performance, so I had no hesitation in deciding that the SMARTMonitor would also be made by KaEdia. After more than two months of ordering, the SMARTMonitor finally arrived.
There was a small product defect there. It was a paint bald on the housing.
I immediately contacted KaEdia and they were able to promptly replace the item with a good one. As expected of JapanBrand ^ ^.
After installing it, the actual feeling on the Motorcycle is perfect!
View detail
No worry about falling off.
There is no sign at all that the 120km/h section of the New Tokyo-Nagoya, the Decoration bumpy road, or anywhere else you might fall off.
Vibration absorption capacity is also very high.
I have tried a few and they are by far the most secure in preventing drops, and if you are really worried, you can easily lock it with Lever.
It is very easy to use as it is easy to connect Charger.
The only complaint I have is that it is difficult to clean because dust tends to accumulate in the groove where it is fitted.
Also, some people have a problem with the way it looks. (Depending on Motorcycle) It may seem a bit lumpy.
View detail
It is quite good.
Although it takes 60 seconds to establish the connection due to the Radio Law, this product uses a soft power supply that shuts down 5 seconds after the ACC power is disconnected, so even if your car model shuts down the ACC power at the time of cell start, as seen in BMW etc., the power will not be turned off when the engine starts. Therefore, if you put on the Helmet and Gloves after turning on the key first, you will be connected to your smartphone by the time you step over and turn on the Cell, and you will not feel the stress of waiting for the connection.
If your vehicle is equipped with a 12~16mm GPS Mount Bracket, the Tanax AIO-5 Mounting Bracket can be used without modification.
The cost performance is great, but the screen size of 4.5-inches is a little insufficient.
View detail
Because it is small, it does not interfere with the Meter and Handlebar area, but the map is also small in its own way.
Other companies have similar products, but I was bitten by the fact that it was a new product. I purchased this product without considering the size of the screen, but it is rather small. When I installed it, it did not interfere with the Meter or other devices, which was probably a good thing,
The large size of the map is the same as that of a smartphone, which is hard on the eyes of an old person, but the instructions are only rough, so you have to learn to use it by hand. Except for the Motorcycle Rose, Wiring is not difficult to install with the color-coded connectors. However, since the Camera connector is the same color for front and rear, it is recommended to temporarily turn on the power during the installation (since the Camera in the back has a reversing function). If you do not use your motorcycle frequently, it is recommended that you connect the ACC and the constant power to ACC separately. If you do not use your motorcycle often, it is better to use only the ACC connection for constant and ACC. I put a switch in the middle of the ACC power supply because the power comes on even when it is not in use. At first I thought the Touch screen response was sluggish, but with my bare hands it was fine, and in my experience it was sluggish with Gloves, but with Gloves, which does not support smartphones, the movement was better. However, the buttons are small enough to fit the screen, so you may end up pressing the one next to it. There is no automatic screen illumination adjustment (I always set it to max except at night. You can set the screen to nighttime, but it's a bit of a hassle). The position of the HomeButton on the map screen is annoying (it can be moved temporarily).
View detail
Easy to use
[How is it used?
I chose to install a new Smartphone Holder on my TouringMotorcycle and ultimately ended up with this product.
Anything as long as it's cheap!" I am very happy to be able to do this, And not too much of Plastic's cheap stuff, either." For me, I'm a bit of an either/or kind of guy. That's it! It seemed like a good idea.
Also, my phone has many buttons on the Right side, so I could not use the type that is inserted from the side, so I chose the type that is fixed at the four corners.
Was the one you received as per Image?
I chose Black and it was just like the Image.
How was your experience with it?
First of all, the Included Parts:are substantial for the price.
There is a diameter conversion rubberretc.Pattern and it is not difficult to install.
When the middle Button is pressed, the four corners are Fit to the phone.
Release is Quantity:Pair (for Left and Right) The only thing you need to do is to press the "+" and "-" prongs, so everything can be done with one hand while doing Gloves, which is easy.
[Points to note]
Make sure it is firmly secured before starting.
How did it compare to other products?
I had been using Chinese several hundred yen ones, but I felt they were well thought out with good strength and ease of use.
【Review】
I used to think that KaEdia was cheap or bad, but when I bought it this time, I got a good impression of Included Parts:, usability, etc.
As a smartphone mount, I have no complaints.
View detail
Easy.
Large is just right.
I change equipment from time to time, and it is useful because I can exchange it easily.
View detail
Touch screen is slow to respond. Instruction Manual is too easy.
The instruction manual only describes it roughly, so you have to learn how to use it by hand. Except for disassembling the bike, wiring is not difficult with color-coded connectors. However, since the connectors for the front and rear cameras are the same color, it is recommended to temporarily turn on the power in the middle of the installation (since the rear camera has a reversing function). If you are concerned about the dark current, the instructions say to connect both ACC and constant power to ACC, but I connected ACC and constant separately because I was concerned about the inability to use the parking monitoring function and the time gap. If you use your motorcycle infrequently and are concerned about battery drain, it is better to use only the ACC connection for constant and ACC. As mentioned in the title, the response of the touch screen is sluggish. It is frustrating with gloves on. There is no automatic screen illumination adjustment (I always use max except at night). The smartphone app is supposed to be able to connect to the driver's recorder, but I don't know the password, so I still can't use it. The home button on the map screen is annoying. View detail
Depends on the use of Main.
I purchased Mirror as Main, which is easy to see during the day.
I bought this one considering the cosmetics including Included Parts:because it was difficult to see the screen in Situation where the sun shines during the daytime with my previous driver's recorder with Monitor.
The screen visibility is not as good as the Tanax SMARTRideMonitor installed on Main's Motorcycle, but if you don't compare it to the Tanax SMARTRideMonitor, you can see the screen even in daylight at a perfectly acceptable level.
In terms of the total price including the Air Pressure Monitor, I think it is a totally reasonable price.
I use it in car play, but when I want to use it in Camera screen, it tries to switch to car play by itself, so I have to operate it each time to switch the screen back.
I would appreciate it if this is fixed in a future version up, but I have no problem using it as a SMARTMonitor.
But overall satisfaction is very good.
If you are hesitant about Tanax because of the price, I totally recommend it. Quantity with the same content:Set is almost half the price, lol.
View detail
Difficult to understand the settings
It does not include a detailed instruction manual, which is a problem when it is not connected to a smartphone.
I set it up while emailing Manufacturer.
Since the Instruction Manual is the same as the Instruction Manual that comes with the DriveRecorder, it is difficult to understand whether it is not displayed due to a defect or whether it was not displayed in the first place.
View detail
Solid, compact, and unobtrusive around the handlebar
The SMARTMonitor has a growing selection, but the KaEdia KDR-D21 is characterized by its compactness, versatility, and high quality. 4.5-inches screen is smaller than a Smartphone, but it is recommended for those who want to refresh the handlebar area. The 4.5-inches screen is smaller than that of a Smartphone.
Installation is easy
Simply connect the power supply (Red and Black) to the Battery and the Attachment power supply (Yellow color).
All that remains is to connect the front and rear Camera and GPS to the Body (Monitor) to complete the SMARTMonitor equipped with a driverless camera.
There are four cords coming out of the Body, but they are soft and not difficult to maneuver.
The connection to CarPlay seems a bit slower than other models, but so far there seems to be no concern about disconnection after a long drive. Also, there is no such thing as losing direction when turning such as UTurn so far.
Since recent CarPlay includes meeting tools such as Teams and Zoom, it may be possible to do things like Touring while talking with multiple people instead of Income connection.
DriveRecorder is generally called highly functional, with beautiful images, and by using the KaEdia application, you can obtain sufficient information even with a Smartphone.
The app is stable in normal use, but in my environment (iPhone) the app crashes when setting up Camera. I hope this will improve in the future.
I have a Handlebar Brace (KDR-HB2) on my CB200X, so I put SMARTMonitor on it.
The company is also a well-known manufacturer of Smartphone Holders, so the product comes standard with an anti-vibration function and seems to have no durability issues.
This was my first experience with the Tire Air Pressure Check, but I was able to Pair it by removing the Pairing on the DeFault and re-installing it again. If it does not work, you may want to remove it from the Valve and reattach it again.
SDCard is not included, so it is recommended that you obtain the necessary Size's first.
Tests before connection can also be performed by feeding power to the USB-CConnector located next to the SDSlot.
(I know it's hard to use USBConnector when it's on-board)
Overall, the quality is good and the features are adequate for the price.SMARTMonitorQuantity recommended for those who are looking for a Compact screen.:Set
View detail
Easy to use
It is a replacement for DAYTONA's Smartphone Holder.
It is easy to install and easy to use.
Vibration absorbing Bumper was installed at the same time.
View detail
Effects not known.
I installed it to prevent my phone from malfunctioning.
The installation itself is easy, but so far the effect is unknown.
It would be nice to have three different hardnesses.
View detail
Excellent workability
Best quality as Smartphone Holder. A product with no complaints in terms of retention, security, and workability. View detail