Reviews
Fits: KAWASAKI Z1000 (water-cooled), KAWASAKI Z800, KAWASAKI NINJA1000 (Z1000SX)
Stylish Stand Hook Bolt by Kawasaki
This is a Stand Hook Bolt from Aftermarket parts of Kawasaki overseas.
The installation instruction manual included in the kit is the English version, and the text is small and the printing is rough, so I could hardly read it. I took a picture of it with my cell phone and enlarged it to read it.
Although the instruction manual did not list the Z900RS as an applicable model, I was able to install it on the Swing Arm using the longest of the three included Spacers for the Left Side and the middle one for the Right Side, even though it was limited.
Maintenance Stand was used, and we could see that the resin part protects the Swing Arm to some extent.
I like the Simple design.
View detail
Fits: KAWASAKI NINJA2 Helmet50RR, KAWASAKI BALIUS2, KAWASAKI ELIMINATOR 250V, KAWASAKI ER-6f, KAWASAKI ER-6n, KAWASAKI NINJA400R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZEPHYRX, KAWASAKI ZRX1100II, KAWASAKI ZrX1200ZrX1200 DAEG, KAWASAKI ZZR1400 (ZX-14), KAWASAKI VERSYS, KAWASAKI VULCANS, KAWASAKI ZRX1100, KAWASAKI ZX-9R, KAWASAKI ZX-12R, KAWASAKI ZX-6R, KAWASAKI ZX-10R, KAWASAKI Z1000
Convenient
I use it with Maintenance Stand and it is convenient because I can hang STAND stably.
Hook bolt is very easy to use and you don't have to worry about scratching the car body.
View detail
Fits: KAWASAKI Z1000 (water-cooled), KAWASAKI Z800, KAWASAKI NINJA1000 (Z1000SX)
US KAWASAKIOEMParts
Original OEMParts from US kawasaki.
I don't know if it's because Kawasaki in Japan doesn't carry them or not, but the webike compatibility chart hasn't been updated at all.
If you can use M8 Stand Hook, it will fit, but you can check US kawasaki Site if you are interested.
As a product, Material:Bobbin and Material in Stainless Steel:Aluminum Protectordisc (with Logo) The combination of the two.
Protectordisc is somewhat matted and has a sense of unity with the Swing Arm.
On the downside, it's expensive.
If you want to buy only Bobbin, you can buy it for half the price of this Parts. If you don't care about it, you can buy it there.
View detail
Fits: KAWASAKI NINJA2 Helmet50RR, KAWASAKI BALIUS2, KAWASAKI ELIMINATOR 250V, KAWASAKI ER-6f, KAWASAKI ER-6n, KAWASAKI NINJA400R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200S, KAWASAKI ZEPHYRX, KAWASAKI ZRX1100II, KAWASAKI ZrX1200ZrX1200 DAEG, KAWASAKI ZZR1400 (ZX-14), KAWASAKI VERSYS, KAWASAKI VULCANS, KAWASAKI ZRX1100, KAWASAKI ZX-9R, KAWASAKI ZX-12R, KAWASAKI ZX-6R, KAWASAKI ZX-10R, KAWASAKI Z1000
Practicality.
The Green Light Hook bolt that I normally use for the Maintenance Stand is the only one that I use for the Custom. I use this product's Hook bolt when I actually hang the Maintenance Stand. It is very convenient to use without worrying about scratches. View detail
Fits: KAWASAKI Z1000 (water-cooled), KAWASAKI Z800, KAWASAKI NINJA1000 (Z1000SX)
After running the car, we found out why it was not included in the compatible models.
The Swing Arm has the Stand Hook mounting holes, but for some reason the Ninja 650 is not included in the Kawasaki OEM Stand Hook.
I bought the other sizes for vehicles that fit the mounting holes of the Swing Arm and tried to install them.
When the maintenance stand was used afterwards, there was not even a thing that was scratched on the body of the car.......but when I ran around the neighborhood a little after maintenance and touched the part to check the looseness of the Mounting Bolt, the exhaust hit or it was quite hot!
There was a good reason why it wasn't in the compliant models.
The resin part might melt if you run for a long time in Touring, etc., so I remove it except when using STAND. 。
View detail