![icon-webike.png](https://thimg-afcc.kxcdn.com/@wth-shop/assets/desktop/img/icon-webike.png)
Reviews
![Rear Inner Fender](https://img.webike-cdn.net/catalogue/images/100693/id5044996_1_TS.jpg)
It is not a pontoon.
It is held in place by 4 hex screws, but it is not a simple screw-in, and the screw holes on the Fender side need to be widened.
It looks Cool.
View detail
![Air Scoop Cover](https://img.webike-cdn.net/catalogue/images/118793_id5045765_2_TS.jpg)
Needs a little processing.
Mounting on zx4r
When we first aligned it, it was not accurate at all.
The warp is so shallow that when I pressed the tip of the Center, both ends floated quite a bit, the largest 8mm floated. It was too shallow to be held by double-sided tape. Finally, I heated the shallow part with a dryer and bent it. Fortunately, I was able to fix the problem by using cheap Carbon, which softened up considerably.
And the depth? I'm not sure if it's not deep enough or if it's installed in the wrong position, but I can see the Green.
View detail
![winglet](https://img.webike-cdn.net/catalogue/images/110991/id5045504_1_TS.jpg)
Good looking Fitting?
Material purchased at Axxon for about $5,000 for about 6 months.:Material of Carbon Style:I was using PlasticYAMAHA Super JOGZr Wing Blackettes. The shape and fitting were perfect, but it looked cheap, so I bought the Barrier sheet.
First of all, the holes are messed up.
Quantity:Pair (for Left and Right) asymmetry (If you force it to widen it, it looks like it could be done, but it might break.)
As mentioned in other reviews, the actual product is different from the picture shown in the introduction! (I'm ok with design-wise).
I managed to install it, and I'm glad it looks so classy. if only I can get through Fitting, it will be Recommendation. No, I'm not going to make a recommendation, but … I'm not going to make a recommendation.
View detail
![winglet](https://img.webike-cdn.net/catalogue/images/110991/id5045504_1_TS.jpg)
Different than pictured, but still nice item
The item that arrived is a different shape and design than what was pictured, however it fit up and still looks nice. I would have liked to have the wing pictured on the product page, but this is all that's available! View detail
![Center Panel Cover](https://img.webike-cdn.net/catalogue/images/118793_id5045793_3_TS.jpg)
so-so
Installation was relatively easy, partly due to the use of double-sided tape.
However, it seems to be floating a little and does not adhere well.
View detail
![Front Winglet](https://img.webike-cdn.net/catalogue/images/100693/id5044997_1_TS.jpg)
Not recommended for people who want to drive a new car to Large things.
I had attached the front with 6 pieces of strong double-sided tape.
The headwind on the windy highway took it all away.
In this case, the Parts interfere with the Front Fender.
It caused damage to both the Side cowl and the original interfering Side cowl.
It may look better temporarily, but is not recommended for those who do not want to regret it afterwards.
I have removed this Parts.
View detail
![Rear Hugger](https://img.webike-cdn.net/catalogue/images/100693/id5044996_1_TS.jpg)
They were in stock and I got them instantly!
I ordered the same product from A-TECH, waited over six months, and then was informed that it would be even later!
I ordered this product from Cancellation and it was in stock and arrived in just two days.
The product is well made and easy to install. I am satisfied.
View detail
![Winglet](https://img.webike-cdn.net/catalogue/images/110991/id5045504_1_TS.jpg)
Shape is different.
The shape differs between the photo and the actual product.
It looks quite like bucktooth.
View detail
![Front Winglet](https://img.webike-cdn.net/catalogue/images/100693/id5044997_1_TS.jpg)
It looks good, but ...
There may be Rose variation in accuracy.
On a 2022 CBR250RR, I could not install it without curving it inward due to the incorrect position of the screw holes.
If you try to install it in that state, it interferes with the Cowl side and rubs against it.
Thin double-sided tape is used for the front side to drop further down to the quantity:1 Set of 4pcs. or so stacked on top of each other.
It will look cool, but I think the double-sided tape will probably come off tomorrow.
I will likely have to machine the Screw hole location when I have time.
View detail
![Fairing Winglet](https://img.webike-cdn.net/catalogue/images/100693/id5044998_1_TS.jpg)
I guessed it, but … it doesn't fit the shape or anything. If you want to put it on, you have to DIY.
The shape does not fit in the first place, as it is made in Indonesia.
Quantity:Pair (for Left and Right) I think you should be prepared for asymmetry.
The price of 10,000 yen is a bit steep for the
I had an idea of what to do, but I knew I had to DIY if I wanted to install it.
Moreover, the carbon surface was cracked.
(I doubt it's even Carbon to begin with.)
I've repaired and reworked all the installation surfaces in File, but I'd like to write this down so that people don't buy it without knowing.
Well, if you're thinking of pimping it out, you shouldn't.
View detail