Reviews
Fits: KAWASAKI NINJA1000, KAWASAKI NINJA1000, KAWASAKI NINJA1000SX, KAWASAKI ZRX400, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS
Essentials for Full Exhaust System Replacement
Purchased to replace with Full Exhaust System.
Failure to replace the Exhaust System when it is replaced may result in waste leakage.
It has always been the case, but it often falls off when replacing Gasket,
It is easier to install if you apply a thin layer of silicon grease and stick it to the Engine side.
There is a way to lightly crush the Gasket circle to make it an oval and attach it, though,
I use Grease because it seems to be less efficient for disposal.
View detail
So bad
I bought it even though it was expensive because I thought it was a reliable manufacturer. However, I could not insert the T5 sphere in all four places because it was slightly too large.
It's a shame because I was looking forward to it.
It's twice the price of cheaper UniversalLEDs, but you'll end up having to buy them all separately.
View detail
Fits: KAWASAKI NINJA1000, KAWASAKI NINJA1000, KAWASAKI NINJA1000SX, KAWASAKI ZRX400, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS
no problem
It is inexpensive and I don't think there are any leaks.
I just put it on so I don't know yet lol.
View detail
Fits: KAWASAKI NINJA1000, KAWASAKI NINJA1000, KAWASAKI NINJA1000SX, KAWASAKI ZRX400, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS
Exhaust System replacement at the same time
Still. The mileage is low, but I changed it at the same time as Exhaust System replacement.
It is safe.
View detail
Gasket
Purchased with the Exhaust System replacement.
Good quality and cost performance.
View detail
Satisfied
Shipped fast and got it cheap! View detail
Exactly
It was just like I expected from Kefalu. View detail
Fits: KAWASAKI NINJA1000, KAWASAKI NINJA1000, KAWASAKI NINJA1000SX, KAWASAKI ZRX400, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI ZX-10R, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z900RSCAFE, KAWASAKI Z900RS
no problem
Replaced with another company's Full Exhaust System from OEM. No problems with installation and no exhaust leakage at all. 4pcsQuantity:I am satisfied with the set and the price. View detail
To install Full Exhaust System
I purchased this product to install the Full Exhaust System on my ZX25R.
I have driven about 1000 km since the replacement and have had no problems.
View detail
Fits: SUZUKI GS1200SS, SUZUKI BANDIT1200, SUZUKI BANDIT1200S, SUZUKI GSX1300R GSX1300R HAYABUSA, SUZUKI GSX1400, YAMAHA XJR1300, SUZUKI BANDIT1200, SUZUKI BANDIT1200S, SUZUKI GSX1300R GSX1300R HAYABUSA, SUZUKI GSX1300R GSX1300R HAYABUSA
Lever is a bit delicate for high price
Cut-out, although it looks luxurious.
The part where your index finger rests has a standing Edge.
The grip wasn't great.
Also, I use OEM between Clutch master and Lever.
Is it an individual difference? The diameter of the bearing tube and the hole in the lever didn't match.
I did not go with Bolt On.
Lever is 11mm and tube is 11.5mm.
It's a lot easier to adjust Lever, but
Not very satisfactory for the high price.
Recommendation is not available for this product.
View detail
Necessities for Full Exhaust System Replacement
Purchased this when I replaced the Full Exhaust System. I think it's reasonably priced. View detail
Required when replacing Exhaust System.
When I replaced the Exhaust System, I also replaced the Gasket. I chose this product because it was a little cheaper than other companies' products. There is no problem at all. I think that it is easy to work because it doesn't fall if I put a little Grease on it because it comes down when I install it as it is. View detail
It cannot be installed
It is A14, but I was not able to install T5 bulbs. Compared with the original bulb, the mating part is a little large and could not be installed. It is in use only. It was past the return deadline and I'm giving up. View detail
It was my favorite Manufacturer, but sorry!
The terminal of the LED ball is thin, the Solder is weak.
Because the polarity was wrong,
Polo, I got a terminal.
Because I set about 2,000 yen for Single Item, I put in things from other Manufacturer.
View detail
I exchanged from foldable lever with BREMBO Racing Master to this K-FACTORY Billet Lever. Same as the original lever, the BREMBO lever had the sharper edge and I didn't like it much. And then I was recommended this part from the bike shop. The
I exchanged from foldable lever with BREMBO Racing Master to this K-FACTORY Billet Lever.
Same as the original lever, the BREMBO lever had the sharper edge and I didn't like it much. And then I was recommended this part from the bike shop.
The edges of lever directory pushed by fingers are rounded and they don't hurt me. I was also recommended the adjustable type, but I said no because I will NOT fell down. I really picked on the lever length. I choose the short one. I don't operate with 4 fingers together, so this size is just good.
Air flow slits make it look more 'racing type,' not just look, the lever resisted to the wind pressure at super high speed. I feel safe and be satisfied.
I installed both right and left side with adjuster for easier operation.
View detail