Reviews
good
I bought this because I was running out of Weight left when I replaced my Tire.
I found it a bit surprising that JTrip, famous for STAND, was selling Wheel's Balance weight.
However, since I usually use STAND of JTrip and feel the goodness of this brand, I think that honestly Weight is the same no matter what I use, but I chose this product this time because I wanted to use the one of the brand that I put my trust in anyway.
View detail
Fits: KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400, KAWASAKI ZRX1100, KAWASAKI ZRX1200, KAWASAKI ZRX400
Bad weld spatter marks.
[How is it used?
Installed external Stand Hook on MT-07.
The Hook is very low, so it was introduced to reduce the force required to Lift.
Was the one you received as per Image?
Unlike the STAND receivers I've purchased, there are so many weld spatter marks that they are unsightly.
A bit of a shame
How was your experience with it?
I was able to lower the Lift amount considerably by using this.
Short roller stands can also be lifted with one hand.
(Originally, you had to put your full weight on it to Lift it)
[Points to note]
Depends on the make of car.
I think that in many cases, the width is not enough unless it is STAND of Wide Type.
(Because I use about 30mm of One Side in Crank part)
View detail
I'm glad I was able to use it.
I switched to NINJA1000sx, and when I tried to use STAND, I bought the color that fits without any research.
If you are looking for the best in the market, you will find that there is a lot to choose from.
I used it because it arrived immediately after ordering and the Size was right.
View detail
Minor change
A while ago, I found out that Rear stand has changed its model.
When I asked for details, he said they just added this part.
Version up to the current model if you wear this!
View detail
Fits: KAWASAKI Ninja400, KAWASAKI Z1000, KAWASAKI ZRX1200, KAWASAKI ZX-10R, KAWASAKI ZX-12, KAWASAKI ZX-14, KAWASAKI ZX-6R, KAWASAKI ZX-6RR, KAWASAKI ZX-9R, KAWASAKI ZZ-R1400, KAWASAKI Z250, KAWASAKI ZSeries, KAWASAKI BALIUSII, KAWASAKI Ninja250, KAWASAKI Ninja300, KAWASAKI Ninja650, KAWASAKI ZRX1100, KAWASAKI Ninja1000, KAWASAKI ER4, KAWASAKI ER-6n
Required for Maintenance
Of course, if you use a V-shaped receptacle, you'll get scratches on the skin.
Anodized will be peeled off If you are worried about it, you should buy Silver.
View detail
It's a Repair Parts product, but it seems to be attached to the recent STAND.
[How is it used?
I used it on my original Rear stand made by JTrip.
I ordered this because I heard that it would eliminate the rattle.
Was the one you received as per Image?
It's a product made in such a way that I wonder why it wasn't made before, but I like this kind of improvement.
How was your experience with it?
It's definitely not rattling anymore!
However, it seems to be no good if the screw hole has been damaged. If you are using the old STAND, you might want to replace it once.
[Points to note]
As long as you pay attention to the direction you attach the Nut, you should be fine.
View detail
It was featured on the Commander's FB page, so...
There doesn't seem to be a STAND that can front up without interfering with Cowletc. in KATANA.
I was introduced to it when I took a peek at the Commander's FB page, so I thought I'd buy it before it was gone...
At that time, Webike didn't have it, so I bought it from another shop.
The installation is not a problem at all, but I don't know if it is individual difference or the hole under the Stem of front 16in. second type KATANA is larger than other vehicles, but with 19mm diameter, it feels like a governor.
He's got a long neck, he's a governor, and he's on the Commander's FB. "Attachment causes Lever to take effect, so riding with STAND-UP, for example... I don't want to overload it because I was warned that I would have to.
In the picture that has been introduced is Black, but the goods that have arrived are per Large? Is it Gold.
It was a shame that it was scratched a little, but it will be scratched with use, so I gave it a finish.
View detail
Ease of use is as good as it looks. How is the texture compared to the front and rear STAND?
I have a similar STAND from UNIT.
I chose this one because the storage Size is Large threshold.
The fact that single tubes are sold in 0.5m increments is just right for the Motorcycle.
1.5m×Quantity:I used 2pc and 1m ready-made as it is.
We have a Large Diameter Pipe cutter, so we can process as much as we want.
Cut the height direction a little more and make it Compact.
It looks like you might want to increase your stability.
STAND has a load capacity of up to 500kg.
It is very sturdy, large and heavy.
However, if the weight is not applied vertically, it will not be very stable structurally.
In the case of high weight, it will have to be used with great care.
The ease of use really is as impressive as the description and appearance.
The point that concerns me is that the insertion hole may be too large for the diameter of the single pipe, and
We use OthersRearMaintenance Standetc. but the quality of the paint is poor. (Weak) I have a feeling.
The availability seems to be poor compared to the front and rear Maintenance Stand, and
I wonder if they're cutting corners because there isn't much demand. I suspect that they are.
Having said that, Ideas is a good product and very helpful.
View detail
Fits: DUCATI 1098, MV AGUSTA Cantilever Swing Arm All Cars, DUCATI 1098, MV AGUSTA All models with cantilever swing arm, MV AGUSTA All models with cantilever swing arm
Don't forget to buy.
Some people might buy the Rear stand and forget to buy the Shaft.
Buy the correct diameter for your vehicle and do not forget it.
View detail
Loss.
When you buy a JTrip STAND, it comes with it, but if you only use it for a certain model of car, you won't use the other colors.
I lost my Large when I decided to use it for a different car model.
Next time I'll make sure to manage it so it doesn't get lost.
View detail
Fits: TRIUMPH DAYTONA675, KAWASAKI NINJA400, SUZUKI , KAWASAKI ZX6R, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI ZX10R, KAWASAKI Z800, KAWASAKI Z400, KAWASAKI Z250, KAWASAKI Z1000, KAWASAKI Ninja 1000SX, KAWASAKI ninja, DUCATI Late 999, HONDA , DUCATI 749, BMW S1000R, BMW S1000RR
Enough for its intended use.
I bought it as a necessary part to use the STAND to hook the STAND. Rather than the paint peeling off in a true aluminum colored product, etc. Good, I decided on this one.
I don't know if DURACON is a rare material or not, but it is 2000 for this one. What do you think of the Yen Over?
View detail
Fits: KAWASAKI Z250, KAWASAKI Z400, TRIUMPH DAYTONA675, SUZUKI , KAWASAKI NINJA400, KAWASAKI ninja, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI ZX6R, KAWASAKI ZX10R, KAWASAKI Z800, KAWASAKI Z1000, KAWASAKI Ninja 1000SX, DUCATI Late 999, HONDA , DUCATI 749, BMW S1000R, BMW S1000RR
It's a little light in color
Easy to install
The drawback is that the color is a little light
The price is inexpensive, so it's a good cosmetic experience
I think it's good for Dress-up Accent
View detail
Fits: TRIUMPH DAYTONA675, KAWASAKI NINJA400, SUZUKI , KAWASAKI ZX6R, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI ZX10R, KAWASAKI Z800, KAWASAKI Z400, KAWASAKI Z250, KAWASAKI Z1000, KAWASAKI Ninja 1000SX, KAWASAKI ninja, DUCATI Late 999, HONDA , DUCATI 749, BMW S1000R, BMW S1000RR
Required to use HookSTAND
HookSTAND cannot be used without it
An L shaped rear stand is fine, but in the case of my car, I have to use the Exhaust System and Swing Arm sensation is narrow, and if you don't get it right, it will interfere with the exhaust system You want to make sure that STAND is raised and stable If you want to service the vehicle, I think you should use HookSTAND Since these are the parts you need to do that, I would be surprised if I bought the vehicle, I would use the Exhaust System I bought it before the
View detail
Fits: KAWASAKI Z400, KAWASAKI Z250, TRIUMPH DAYTONA675, SUZUKI , KAWASAKI NINJA400, KAWASAKI NINJA1000 (Z1000SX), KAWASAKI ninja, KAWASAKI ZX6R, KAWASAKI ZX10R, KAWASAKI Z800, KAWASAKI Z1000, KAWASAKI Ninja 1000SX, HONDA , DUCATI Late 999, DUCATI 749, BMW S1000RR, BMW S1000R
I was just..
I bought Black for my NINJA1000SX
Installation takes only a couple of minutes with a hexagon
I don't expect it to be very durable because of the Black paint in Aluminum
There doesn't seem to be any interference with the AXIS Lapo's exhaust system, even with two people in the car
OEMs are unchecked
The downside of the largest is that the recessed area is the Swing Arm and [Color] Too little Clear, so the Y-shaped Bracket makes contact
It would be nice if they could improve the dimensions of the unevenness of the product, although it may be a universal product
View detail
No V-receiving Rubber!
Purchased at the same time with Aluminum Hook Bolt for NINJA1000SX
Adjusting the width, the first time the rubber breaks and scratches the swing arm..
I think we need a little more room to play
The performance itself is not a problem, but the Hook bolt or Y-type rubber strength needs to be improved
If you're considering buying one, you can use Tape to cure the Rubber and Swing Arm before use You should either cure it or make it L-shaped
View detail
Fits: HONDA VFR750F, HONDA RVF750, HONDA VFR400R, HONDA RVF400, HONDA NSR250R, BMW F800S, HONDA RVF400, HONDA RVF750, HONDA RVF400, HONDA RVF750
MC28 Type 94 - Matching with NSR is not enough
Application of MC28 Type 94 to NSR
Because the shaft on the STAND side is too long, it cannot be inserted to the depth of the hub (If the insertion is shallow, it will be unstable) (that is)
The shaft outside diameter is slightly smaller than the hub hole (inside diameter) (less than 1?)
When NC30 VFR is applied (no problem)
Since the shaft for CenterWheel fastening is not used, the shaft on the STAND side is not used I was able to get all the way in
The fit between the hub hole inner diameter and shaft outer diameter was appropriate
View detail
Cheesy
I bought it a few years ago and I think the quality is poor for a JAPAN
The paint is weak, rust easily, and the plating of the receiver is also weak Also the welding bead is dirty and expensive
View detail
sufficient for one's needs
It's a good thing that the hooks can't be shared with other companies' products It is
The paint peels off and rusts and becomes unsightly as you use it, so this is a rust-resistant material:I hope it's Stainless Steel, although it looks like the Plating one came out It's expensive and this one is sufficient
View detail
It's a shame because it's a manufacturer's product
I don't think that only a well-known manufacturer can ship a product in a dirty condition
There was something black and sticky like a tar on it and some of the paint was peeling off
Probably not from the manufacturing process, but from the packing process
I was convinced that it wasn't worth returning or exchanging, and that with use, it would get dirty and the paint would come off has lost confidence in it
View detail
Is the price high?
Even when compared with MaintenanceSTAND about 3,000 yen
The difference is that Roller is doing it properly. Ease of use has not changed.
I feel like I lost something.
View detail