Reviews
A classic?
I used it on a SEA BASS STAND, probably an OEM SEA BASS from J-TRIP that I purchased over 10 years ago.
I used to use a Swing Arm with a receiver on the Hook.
I bought a Ducati MONSTER400, so I bought this one too.
I could not find any Bolt on MONSTER400 that would attach a receiver to the Swing Arm.
Installation is simply a matter of replacing the Hook that was previously attached.
The Rubber seems thick and rigid enough to hang STAND with confidence.
I don't have a Spec. because I'm Firmly, but it would be nice if the price was a little lower.
Well, once you buy it, you can use it for more than 10 years.
View detail
Use at your own risk.
I bought a reverse attachment for the Rebel 1100 and used it, but the attachment on the Sprocket side did not fit properly and the tires did not rotate properly. I was told that if I put this Attachment for 250 or 500 on the Left Side and STAND-UP, it would solve the Stress problem;
I have not had a chance to try it yet, but I purchased it with a light feeling that if it does not work, I can just use the reverse Attachment.
The product is JTrip, so you can be sure of it.
I am satisfied with the Large change because the shipping was promptly done by WeBig.
View detail
Designated items sold separately.
As per Title, it was a Manufacturer specified product of the RearMini stand prepared for the Z125PRO, and when I checked it when I purchased it, I always have the impression that it has a solid and sturdy finish.
Package. It's not slippery." It was! It is true that it is not slippery, but there was a case that it slipped a little in the initial stage of purchase due to the oil content from the compatibility with the paint of Z's Swing Arm or from the side work.
The resin of the L-receiving part, which is often a problem in overseas products, is welded with a thick urethane-like material, and there seems to be no problem with durability or aggressiveness to the Swing Armetc.
The rotation of the L-supporting part is also light, and when lifting the swing arm, simply place it horizontally on the car body and it will be attached to the swing arm. The stability of the Swing Arm is more than just the swing arm on the L-support, and the work can be done with a sense of stability and security.
As mentioned in Manufacturer's comment, we need to pay attention to the slippage caused by oil in the lower part of the Swing Arm, and now we always clean and wipe it off thoroughly before using it.
View detail
Use L4 for medium-sized vehicles.
The L4 can be used on a Large for Vehicle, but it sticks out a little more than the width of the Swing Arm, so I had to use it without interfering with the LimitSprocket. It was safer to purchase L4 for medium size vehicles. View detail
Either is required
Either L- or V-shaped receptacles are required View detail
It is a good, solid product.
Purchased for installation on a short roller standsJT125. I am not sure about the thickness of the penetrating shaft, but the overall construction is solid, so I can use it without any problem. View detail
jtrip first time STAND
I don't know if I have ever used the L or V receptacles, but I was able to raise them easily for the first time. I use it for storage. View detail
I bought it again.
Cushioning was also available, and the receptacle on the Swing Arm itself appeared to be falling apart.
However... after I bought it, I realized that the raggedness was just visible, but in reality it was just dirt... You can't look at it when you are tired.
Compared to the cheap STAND L-shaped receptacles, the quality of the Cushion section is better, first of all.
The cheap ones are thin rubber boards, while this product is a thicker, slightly softer board.
Damage to the Swing Arm is definitely less here.
View detail
usually
It can be used normally. It is a first-class manufacturer, so you can use it with peace of mind. View detail
Rubber Receiving Straight
It is easier to use than the L receipt and can be lightly Lifted up.
I am also wondering about the durability of the Rubber.
View detail
Stand for Beginner did not fit and I purchased an additional one.
At first I was scared to do STAND Up and Down, but once I got used to it, it was easy. View detail
Better than Hook type
I used to use Hook type STAND, but I changed to VPlate and will compare the two.
The groove of the shaft and the Plate mesh with each other, so the Quantity:Pair (for Left and Right) The stability of the system is stable with little blurring of the
Material:The plastic material provides good sliding and reduces the force required for Lift.
The Hook type can be scratched by rubbing against the Swing Arm if one is not careful, but the V-Type is less likely to be scratched because the roller part runs away from the Swing Arm to the outside.
Hook type has a risk of damage to the swing arm or the female screw when it falls over, but the Plate type does not.
As for the demerit, the Plate on the body side is more expensive and heavier than the Hook type, and the Roller itself is also expensive.
Plate is definitely better than Hook if budget allows, as Merit is the only one in use.
View detail
Put it on the Body...
I can't use it without it, so I bought it, and I want it to be Standard Equipment. View detail
It's stable.
It is considerably more stable than the V-receiver. It's usable. View detail
Purchased for 92 Grom RearMaintenance
It is sold separately from Narrow Roller Stand 8-18, so there is nothing special about it, but it looks sturdy.
The BoltHandlebar for positioning is plastic, so I am concerned that it may break over time, but if it is not tightened too much, it may be large and strong.
The contact part of the Swing Arm is Silicon type? I think this is a good idea because it reduces the risk of damaging the Swing Arm by a large amount.
View detail
high
You can't float without it.
They are solid but expensive. A few years ago you could buy them for 2,000 yen, but the quality hasn't improved and they are getting more and more expensive.
The cosmetics are very poor.
View detail
Replacement from L-shaped receptacle
[How is it used?
Maintenance Hook bolt was installed on a Kawasaki Z400.
Z400 (New ModelNinja400/250Series) The ABSSensorWiring of the Rear brake is located directly under the Swing Arm, and an L-shaped bracket may cause the Wiring to become engaged and break, so a Hook bolt and this product were prepared.
Was the one you received as per Image?
As per Image.
The plating was well finished, and naturally there were no Bolt defects, so we were satisfied with the quality of the product.
How was your experience with it?
The hook bolt is also made by JTrip, so it can be fitted with a Large change and easily STANDed.
Naturally, SensorWiring is not interfered with and is stable even when STAND is applied, so maintenance is also facilitated by the Large change.
For vehicles with a hook bolt boss, it is highly recommended to install a hook bolt and STAND with the V receiver.
I regret that I should have realized this quality earlier.
[Points to note]
I may not have adjusted it properly, but the side of the V-supporting part hits the swing arm, so when it does, I think it is better to cure the gold part with something as shown in the photo.
I cure myself with Vinyl Tape.
How did it compare to other products?
Compared to JTrip's L-shaped receptacle, this product's V-shaped receptacle is definitely easier to STAND and has outstanding stability even when STAND is applied.
I have maintained all but the Off-road vehicles I have driven in my career with the L receiver, but I wish I had changed to the V receiver earlier.
[ITEMS TO BUY TOGETHER
Hook bolt
Tapeetc. curing the side Gold genus part of the receptacle.
View detail
Cheap insurance and peace of mind.
It increases peace of mind because you no longer have to worry about the receiving Bracket coming off and damaging the vehicle body. It is a cheap insurance. The question is how long it will last in terms of strength. View detail
That's j-trip!
I bought a Maintenance Stand for my MONKEY125 and this "V receive" purchased
I have only used it a few times, but will review how it feels at this stage.
First of all, the quality is very high quality, and the material seems to last for 10 years even if used hard.
This V-receiver is protected by Rubbers front and rear, so it is not likely to scratch the body of the car (even if it is used incorrectly).
The drawback would be the high price. I think the price is reasonable for this texture. However, if you get the maintenance stand and the receiver together, it will cost you quite a lot of money. But it guarantees peace of mind.
Beginners should be careful not to install in the wrong direction.
View detail
Fits: DUCATI MULTISTRADA 1000DS 1000, DUCATI STREETFIGHTER848, DUCATI MONSTER796, DUCATI Multistrada 1100/S, DUCATI MONSTER1100EVO, DUCATI HYPERSTRADA, DUCATI MONSTER1100/S, DUCATI HYPERMOTARD796, DUCATI 996, DUCATI 998, DUCATI 848, DUCATI 916, DUCATI 748, DUCATI 748, DUCATI 848, DUCATI 916, DUCATI 996, DUCATI 998, DUCATI HYPERMOTARD796, DUCATI HYPERSTRADA
Used on ducati998.
This is Shaft, a cantilevered Roller stand.
Without it, nothing is possible.
If it is a compatible caliber, it will go in easily.
I used it for about 4 years and it was not damaged, just rusted.
Rust used AZ rust inhibitor.
View detail