Reviews
The Front Fork up stand of J-TRIP. It was used for M900. -- this which it already has -- moreover It is used together with the Rear stand (penetration Type) of J-TRIP. It is easy rather and very well. In an easy Maintenance and Wax UP,
The Front Fork up stand of J-TRIP.
It was used for M900.
-- this which it already has -- moreover It is used together with the Rear stand (penetration Type) of J-TRIP.
It is easy rather and very well.
In an easy Maintenance and Wax UP, I think that it is right just by Colet.
It is exclusively for the Type which has a hole in
Fork lower end.
The
Wheel can also be removed.
It is rather good.
View detail
It purchased to the Maintenance. It also has the Front stand. The difference from the Front stand is a price first. The Front stand is higher. -- Since it is cheap, a using feeling is how... although ? was thought, it i
It purchased to the Maintenance.
It also has the
Front stand.
The difference from the
Front stand is a price first.
The
Front stand is higher.
-- Since it is cheap, a using feeling is how... although ?
was thought, it is rather surprised about [ good ].
If it is
anticipated use, it is enough here.
The power in the case of the
Lift is not needed rather than a Front stand, either.
It is different to the extent that it is surprised compared with the
Front stand.
Although the direction performed to
Front-fork attachment and detachment is a Maintenance stands, probably, the direction which
Meets and out of which it does not come will be enough here.
It is cheap, is easy to raise and does not take a place.
Is it just the best?
View detail
Usage is very easy, is put in the hole of a Fork, and only pushes down to the front. Also when pushing down, weight is not felt so much. Wheel washing at the time of the car wash became very easy.
Usage is very easy, is put in the hole of a Fork, and only pushes down to the front.
Also when pushing down, weight is not felt so much.
Wheel washing at the time of the
car wash became very easy.
View detail
In the case of FZ1, in the STAND of the conventional J Trip, since it cannot be used for the Joint of a Brake hose, interfering, it purchases. Since width is changeable, if a hole is located at the bottom of a Fork, every vehicle type can be used. W
In the case of FZ1, in the STAND of the conventional J Trip, since it cannot be used for the Joint of a Brake hose, interfering, it purchases.
Since
width is changeable, if a hole is located at the bottom of a Fork, every vehicle type can be used.
With [ even if the die length of a Fork is different by right and left like
FZ1 / since a STAND has a height regulating function ] no problem.
handling is also easy and it is large satisfaction.
View detail
Since a hand did not come out from beforehand easily although it wanted, but it is Front-brake-disc exchange, he has bought it at last.As it is, although user-friendliness was heavy at the time of a Lift up, the unstable feeling did not feel
Since a hand did not come out from beforehand easily although it wanted, but it is
Front-brake-disc exchange, he has bought it at last.As it is, although
user-friendliness was heavy at the time of a Lift up, the unstable feeling did not feel it.
It is the shin without being able to use, if there is also no Rear stand although merely written also on the description.
View detail
[Webike Monitor] Since NSRmini was got, it purchased, although maintenance of the circumference of a Front is carried out. Although the Front stand for the Mini bikes has come out of two kinds of J Trips, that of the cheaper one falls during main
[Webike Monitor] Since
NSRmini was got, it purchased, although maintenance of the circumference of a Front is carried out.
Although the Front stand for the
Mini bikes has come out of two kinds of J Trips, that of the cheaper one falls during maintenance, is so and chooses here.
Although it also has the object for
Big bikes, structure is solid even if it becomes small.
Although the
Jack can be substituted, maintenance will become markedly easy if it is.
View detail
Although JT-113S raised with F-Fork was used before, since it was inconvenient to OH F Fork, it purchased. As a result of , work becomes easy, buys it and thinks that it was good. Since a Space is required although however folded up with a thin
Although JT-113S raised with F-Fork was used before, since it was inconvenient to OH F Fork, it purchased.
As a result of
, work becomes easy, buys it and thinks that it was good.
Since a Space is required although however folded up with a thing with a high price, it may be inconvenience at rice cake progress.
When using it for an APE and XR, it is used, making a hole in F Fender, but with attached parts, unless it removes F Fender, it cannot use.
I am an ETHOS Ethos. : Up-Fender correspondence The Front stand adapter is purchased and used.
(Since the Size of an attachment does not suit, the Tape is rolled and adjusted) Work became possible now attach [ F Fender ].
Since it is an object for MINI, I would like you to correspond by Manufacturer normal from the beginning.
View detail
the Front stand was [ br ] borrowing although the Rear stand had its own thing until now -- it is very convenient if you are too. This product was easy-to-use. It is also good to be able to perform height control. It could correspond to variou
the Front stand was [ br ] borrowing although the Rear stand had its own thing until now -- it is very convenient if you are too.
This product was easy-to-use.
It is also good to be able to perform
height control.
It could correspond to various Motorcycles in an attached color.
Front-fender Brake-lever Bikini-cowl Blinker from which the metal fittings which are made to raise the STAND which
, however I bought, and are fitted over the hole under a Stainless in about 12 hours broke, and the Motorcycle broke down is damaged,
Crack countless in a right-hand side side ... Is it
individual specificity (?)? is it better ? and to seldom keep raised for a long time?
It is the minimum for the time being.
View detail
It purchased mostly for Front-wheel cleaning. Although the Wheel was turned using the Roller before , it decided on purchase taking advantage of the Tire having become a thing in which it is quite heavy to turn a Wheel falling from a Roller, if
It purchased mostly for Front-wheel cleaning.
Although the Wheel was turned using the Roller before
, it decided on purchase taking advantage of the Tire having become a thing in which it is quite heavy to turn a Wheel falling from a Roller, if it is used where a rear side is also raised.
Although early adjustment is trouble a little, the comment to purchase,
If even it finishes, power is needed for ♪ [ positively easier-to-use than a Roller ]
Raising a little, but since a Wheel can be turned single hand after that if it raises, it is also an easy victory to turn a Wheel to one hand with a Sponge.
Although the character top Front fork of the
products cannot be removed, I think that the work to there is a product good for how which the intention of carrying out twists.
View detail
It is used by zep750. Since it was a center stand wearing vehicle, although attachment and detachment of the rear wheel were easy, they needed the jack-up to remove a front. Removing an undercowl each time purchased this product as what can carry
It is used by zep750.
Since it was a center stand wearing vehicle, although attachment and detachment of the rear wheel were easy, they needed the jack-up to remove a front.
Removing an undercowl each time purchased this product as what can carry out front up that it is troublesome and simply.
Height is thrusting the bit of a receptacle portion and width has a configuration adjusted by tightening the nut of a wheel shaft.
If even reliance uses this stand as the Faulk lower part correctly after standing a center stand and making a car body and a handle straight, a lift can be simply carried out by the principle of a lever.
Although it wavered with the front up stand which carries out the lift of the stainless portion,
Since maintenance of the circumference of a stainless required the jack (motorcycle lift) as usual although there was a difference of the propriety of front fork desorption, the use was limited to wheel desorption, the point which has a small light weight was thought as important, and the fork up stand was chosen.
A size near incidentally weighs [ 350 mm in width, 650 mm in die length, and ] about 2.7 kg.
According to the description of product enclosure, combined use of a rear stand is recommended and the combination with a center stand is improper, but if it is a desorption grade of the wheel of what lacks in stability a little, it can be satisfactorily used also in combination with a center stand.
If the work which loosens an axle and which applies the power of fastening is done where a wheel is grounded beforehand, I will think that there are also few danger electricals of a fall.
Although the crack to a car body is just going to be worrisome, the bit point is + character and it receives the Faulk bottom in a crossbar portion.
I think that some cracks enter although it is a round bar.
Since the bolt which fastens an axle and is crowded has [ removing and ] directions, the screw thread of a bolt is not crushed.
In addition to the ease of carrying or storage, I think that it is an effective tool in order to carry out front up simply by a center stand wearing vehicle (they are individual comment).
There was no exaggeration like a tidy front up stand, and since he wanted to use full-marks evaluation since it had agreed enough for my use and the purpose, but price setting was slightly high, this evaluation was used.
In a function surface, it is perfect.
We recommend you.
In addition, since the combined use with a center stand is directions which a manufacturer does not recommend, please perform it also as judgment of you and that of responsibility.
View detail
Although the front stand was purchased for the first time, it is as convenient as he repents of why even Kon did not purchase. If only height is tuned finely, the rest will be lightly gone up, supporting single hand so that it may not shift uniting a
Although the front stand was purchased for the first time, it is as convenient as he repents of why even Kon did not purchase.
If only height is tuned finely, the rest will be lightly gone up, supporting single hand so that it may not shift uniting a location with the hole of the Faulk lower part, if it already pushes in by hand of one of the two.
Since it does not remove by itself although it is if a wheel can also be removed, it is used only for cleaning of a wheel and a tire.
however -- so much -- also coming out -- working efficiency carried out UP substantially.
View detail
Since there was a casual income although it regarded as ? whether it would be to a front although it had the stand of RIA and purchase was not carried out, it purchased. It was good to buy it. They are items very convenient and required now. t
Since there was a casual income although it regarded as ? whether it would be to a front although it had the stand of RIA and purchase was not carried out, it purchased.
It was good to buy it.
They are items very convenient and required now.
this -- please carry out facilities experience.
View detail
Maintenance is to a tire change, and since it did not consider desorbing Faulk, this product is purchased. Since there is no sense of stability in the state where it is raising when raising not much, considering the safety at the time of work, the typ
Maintenance is to a tire change, and since it did not consider desorbing Faulk, this product is purchased.
Since there is no sense of stability in the state where it is raising when raising not much, considering the safety at the time of work, the type which puts a stand and raises it under a stainless is better.
However, since the frame of a stand does not come beside Faulk or a wheel, it considers [ that this one may tend to work and ] here.
Merit also with big not taking a place to storage, either.
View detail
It is used in suzuki B-KING. In order to have removed the wheel on the occasion of a tire change, when enough, it chose here. However, although it is easy to be to 400, it is past a pile at a liter class. Honesty and raising are hot. A lit
It is used in suzuki B-KING.
In order to have removed the wheel on the occasion of a tire change, when enough, it chose here.
However, although it is easy to be to 400, it is past a pile at a liter class.
Honesty and raising are hot.
A liter class recommends you a front stand.
View detail
It purchased to the maintenance + car wash. It is used by CB1300 (SC54). Although purchased by the thing that it can be used for the bottom of a front fork by the vehicle type in which a hole of 8 mm or more has opened, by heavy motorcycle, a hang
It purchased to the maintenance + car wash.
It is used by CB1300 (SC54).
Although purchased by the thing that it can be used for the bottom of a front fork by the vehicle type in which a hole of 8 mm or more has opened, by heavy motorcycle, a hang is required like CB.
It will not go up, if the hole has shifted.
Although power does not need the guide peg from a hand, on foot, it is slightly difficult.
(It is better to press down so that a hole may not shift however by hand) Although a storage place does not take space, either, since it is small, if it can do, I will recommend a front up stand.
View detail
desorbing a front tire -- now -- until -- although the jack and the rope were used together and the car body was supported, since it was in that work takes time and a state with an unstable car body, this product was purchased. The place and car body
desorbing a front tire -- now -- until -- although the jack and the rope were used together and the car body was supported, since it was in that work takes time and a state with an unstable car body, this product was purchased.
The place and car body which may be used are stabilized, and working hours can also be shortened.
- A front is simply raised by the effect of a roller.
The paint application which touches - ground surface a dissatisfied place separates soon, and carries out.
It uses, and since this is convenient, it is recommended.
View detail
By tire change, car wash, etc., he thought whether it would be required and I purchased. A price is also enough to use that it is handy and ordinarily. It is convenient, if there is one since it can be used for almost all motorcycles by the type i
By tire change, car wash, etc., he thought whether it would be required and I purchased.
A price is also enough to use that it is handy and ordinarily.
It is convenient, if there is one since it can be used for almost all motorcycles by the type inserted in the hole of the Faulk bottom.
View detail
Since the opportunity to raise a front at the time of subsequent fine adjustment and maintenance increased with disk-izing of an ape, it purchased. Hereinafter, I list merit and a demerit. Merit (1) It becomes very easy to float a front, although
Since the opportunity to raise a front at the time of subsequent fine adjustment and maintenance increased with disk-izing of an ape, it purchased.
Hereinafter, I list merit and a demerit.
Merit (1) It becomes very easy to float a front, although it is natural.
(2) He can feel easy when removing a wheel by a tire change etc., since Faulk is supported firmly.
Demerit (1) Using this product, combined use with a rear stand will be the requisite.
(2) Paint application of a ground surface and the field to ground will come off inevitably.
I think that maintenance or the direction carried out custom purchases a motorcycle frequently by themselves, and it does not carry out loss. [ general comment ]
Although it is called a mini bike, if there is no stand, the work held with a front floated will be dangerous, and physical strength will also use it.
As a measure against the point which a color peels off, if a rubber board is stretched with double-stick tape to an earth side with a ground surface, it can prevent paint application coming off.
View detail