Reviews
substitute for an another
I bought this for a replacement for a plastic hammer that had a scratch or dent on the head. View detail
Replaced with a reliable manufacturer's product for future Motorcycle tinkering.
[How is it used?
I used to use a tool sold at Home center, but I was licking the Nut and so on.
We purchased this product as a reliable manufacturer's product.
Was the one you received as per Image?
Matte texture, Laser marking and was as per Image.
How was your experience with it?
The dimensional accuracy is also no problem at all, and it is good to fit Snap to Nut.
Matte texture also fits well in the hand.
How did it compare to other products?
It is a world of difference from the inexpensive tools sold at Home center. A little more.
I regret not buying it earlier.
Requests, etc. to Manufacturer
When the tool box is stored upright, it is unstable because of the protruding hinges,
I would like to see a structure that does not stick out.
View detail
Purchased for personal use
[How is it used?
Purchased as an on-board tool for my motorcycle
Was the one you received as per Image?
KTC, so the texture is good and just like the Image.
How was your experience with it?
It fits with Snap and has good dimensional accuracy and can be used with confidence.
It is inexpensive, so it's great for personal use.
View detail
Good texture
[How is it used?
Purchased at the same time as the 65-piece AutoMechanic set from the same manufacturer.
Was the one you received as per Image?
The Matte texture is pleasant to the touch and the Laser marking is very clear.
How was your experience with it?
There is no dimensional error and it fits Snap and Nut so it is safe to use.
View detail
OEM products of other Manufacturer?
[How is it used?
When SUZUKI/CHOINORI replaced a tire, the air valve was cracked, so this tool was used to replace it with an OEM product.
Was the one you received as per Image?
It was just as Image.
Perhaps this product is the same manufacturer as the products sold by AstroPROducts, Amazon, etc.
The color, shape, etc. are similar.
How was your experience with it?
There were no problems with use at all.
A fair amount of force is required to pull the Valve.
[Points to note]
When connecting to Valve, it is necessary to remove the Parts called Insects in Valve.
How did it compare to other products?
I have not used other Manufacturers, but I think the low-priced ones are sufficient because there is almost no difference in Gold amount.
View detail
It can be used without problems
I used it to tighten the Stem Nut on my Motorcycle during the Restore process, I used it on a Plate type Torque wrench and was satisfied with the Torque management without any problems. View detail
Stem wrench, this is all you need
[How is it used?
The XR230 Stem has a bad habit of coming loose, so I tighten it up regularly with this.
So far I have not had any problems using it.
It is very inexpensive, so it is convenient to keep one of these in your tool box.
View detail
It's a good thing to have.
The socket system was unified with a 3/8 socket angle, but only Impact had a 1/2 size socket angle, so we could not share the same socket. I bought this one because it is cheap and can be shared. I am not dissatisfied with the quality and usability. View detail
3/8Deep socket
Other than that, it is usually possible to set the Socket to Quantity:I wanted a Deep socket since I have it as a Set. I purchased 6 types of this product for my needs of Size, 8, 10, 12, 14, 17, and 16 (Plug socket). 。 The Bolt and Nut are firmly supported when tightening and unfastening, and I felt a sense of security when using the Bolt and Nut. 。 Also, the size markings are clearly written, so they are easy to read. I just started using it, so I am not sure about its durability, but it is well made, so I do not think it will be a problem. 。 I am very happy with it View detail
I am afraid of Short and I love it!
I love it because I had a scary experience with it once when I was changing batteries on my Motorcycle and I had to short it out! It is a little on the Large side for Motorcycle use, but I have no problem using it! It is a little bit Large for Motorcycle use, but I can use it without any problem! I am very happy with this product! View detail
Used to disassemble Clutch in LETS4Palette
I bought this because I needed it to loosen the 34mm nut when disassembling the Clutch on the LETS4Palette.
I chose this one because of its high cost performance, and I had no problems with its functionality or strength.
View detail
DAYTONAFilter wrench
I bought it for my motorcycle, but I can also use it in my car. View detail
DAYTONA Filter wrench
I bought it for my Motorcycle, but it can be used for my car as well. View detail
Increased work efficiency
Used to remove and install Crank Case Cover
Convenient and reliable
View detail
Used for detachment of Clutch and Flywheel
I think it is a reliable Manufacturer.
If there is oil on it, it will not hold firmly.
Large cut is to degrease the part to be removed and the place where the tool comes in contact with it!
It was easy to use
View detail
However,
You need to be careful because it is super strong, but the Series of this one is the only one you can grab. View detail
The stuff is good.
I had left it to the dealers, as I could not see the position of the plug under the tank on recent motorcycles, but I bought it to replace the Eliminator125 plug after a long time.
I chose the one that fits Plug without thinking, but the product precision is excellent and beautiful.
If you fit it directly to the Plug, it goes in easily and with very little play, Wrench is easy to handle.
View detail
Ordinary Socket
One day I looked at the Socket set and found that the 10mm was missing, which I assumed was lost because it was used so frequently.
I purchased the SK-11 as my first choice.
It came out of the tool box after purchase. I don't care how many I have, I will use it as a Socket for Touring's tools.
View detail
Ideal for Driven Sprocket Nut
I purchased the 12mm to replace the Driven Sprocket on my KLX125.
As a result, I am satisfied with Large!
If you have ever replaced the Driven Sprocket on a KLX125, you will know that when holding the Nut on the Driven Sprocket, the Neck is where the Rim/Tire is located.
LongGlasses/Spanners interfere with the Rim/Tire, so the tool must be hung on the Slant, while ShortGlasses and normal length Spanners are too short to hang the Torque.
I had been using Long spanner, but I thought it was not a good idea, so I bought this one.
Good point #1.:Moderate Offset
The handle and Glasses section are moderately offset so that the Nut can be held without interfering with the Rim/Tire.
Good point #2.:thin
Related to (1), it is made thin and does not interfere with the Rim/Tire.
Good point #3.:No counterbore in the Glasses area.
They have eliminated the counterbore, so the Nut can be held firmly even at this thinness.
Good point #4.:Simply cool
I like UNIT tools and have several of them, they are cool.
The ruggedness of the black color, the UNIT logo shining on it, and the gentleness of the handle covered with rubber.
It's a hobby of mine, but I just can't get enough of this coolness.
It is not so frequently used for personal use, but it is very useful when replacing a Driven Sprocket! It is a very useful tool when you need to replace a Driven Sprocket.
When in doubt, buy. Please try it out at Su Chest in
View detail
Tools used only occasionally are SK11
I use basic KTC and Tone for tools.
I use SK11 for tools that are used only occasionally.
Insert angle of this Deep socket:6.35mm (1/4Inch) Purchase
Sprocket Coveretc.It is necessary to remove the bolt that is deep in the bolt, and it is necessary to remove the bolt that is deep in the bolt.
Frequently used insertion angle:9.5mm (3/8Inch) Deep socket in the
If you try to use the 8mm, the Ratchet Pouch opening will be
It's thicker, so it hits the Cover.
So, insertion angle:6.35mm (1/4Inch) will be needed
But I don't use KTCetc. so I don't want to buy KTCetc. for my Wallet...
Thank goodness for SK11's Socket
Reliable quality at a reasonable price
I use KTC and Tone where I hang Large Torque.
The parts of SmallTorque that are not used much are supplemented with SK11.
View detail