Reviews
Fits: HONDA NC750X, HONDA CB1300SUPER FOUR SP, HONDA CB1300SUPER FOUR, HONDA CB1300SUPER BOLD'OR SP, HONDA CB1300SUPER BOLD'OR
Clamp set for Attachment Cross Bar
This product is listed in Honda's OEMAttachmentCatalogue and is installed in combination with the Shaft for AttachmentCross Bar.
Current NC750X (from 2021) I purchased this product because the OEM Knuckle guard is attached to the Handlebar Brace, and I thought it would not be possible to install the Handlebar Brace with a regular Handlebar Brace Clamp because of the Cable clip in the mounting position. This product has a thin wall so the cable clip can be easily fended off and installed.
Since the standard outer diameter of 22.2mm can be used for installation, it can be used for other purposes in addition to handlebars, depending on the ingenuity of the user.
I wish they were the same color because the Bolt and Washer are Silver and the color looks floaty lol.
View detail
Fits: HONDA CB1300SUPER FOUR, HONDA CB1300SUPER FOUR SP, HONDA NC750X, HONDA CB1300SUPER BOLD'OR, HONDA CB1300SUPER BOLD'OR SP
Shaft for Attachment Cross Bar
This product is listed in Honda's OEMAttachmentCatalogue and is to be installed in combination with the AttachmentCross Bar Clamp set.
The outer diameter is 22.2mm, the same as a standard handlebar, so attachments can be attached to the handlebar.
Current NC750X (from 2021) This product could be installed with a pre-2021 OEMOption Knuckle guard that does not have an Option setting on the
I do not think it will play the same role as the Handlebar Brace, but it will serve well enough to attach other attachments.
View detail
It was a little short!
After installing Extension India on PCX, Mirror and Extension India interfered with each other, so I bought this as a countermeasure. I had no choice but to adjust it by shifting the Extension India, but the interference could not be improved, so I decided to ride it as it is. I will buy OffsetHolder45 later. View detail
This curved Bracket is exquisite.
[How is it used?
Purchased this product for ease of use when installing a DAYTONA external power supply extraction Socket on my multi-purpose SEROW250.
I was looking for a short type mount bar, even if it looks a little messy, but I decided it would be better to use it easily. I was looking for a short type mount bar when I found it in Webike's product introduction section.
How was your experience with it?
I don't like the mess around the Handlebar, but when I used it, I found the USB Power Port easy to use and the Large Change convenient, and I understood why so many Mount bars are sold... (Thoughts of a middle-aged man who is about to be overtaken by the times).
The product was exactly as shown in the Image, with the smallest possible Refreshing Type.
How did it compare to other products?
This is a common Type used to bite into Mirror Holder.
The curved Mount Bar Connection Bracket is fixed to the L-shaped Bracket that is fixed to the Mirror Holder, and can be moved back and forth to allow the Mount Bar to be positioned at a convenient location for the user.:Can be set.
This curved connection bracket is exquisite and allows for a lower quantity position than is possible with a straight design bracket.:I am impressed with the wonderful Ideas because I can Set.
[Points to note]
By Mirror Holder For 8mm For 10mm Check the screw size of the Mirror of the vehicle you wish to install and be careful not to purchase the wrong one.
Manufacturer-wise. For LeftMirror The curved Bracket is not impossible to install on the Right Mirror (although the curved Bracket will be warped in the opposite direction).
Quantity to Position easy to use for Spec. cars.:Once set, please tighten and secure each part firmly, otherwise you will be in a panic if it loosens while driving... (this is my experience)
Other items that would be helpful
The deciding factor in the purchase
As mentioned above, the short type mount bar and the exquisitely curved bracket are the deciding factors.
【Included Parts:presence or absence】.
L-shaped Bracket for connecting Mount Bar Body and Mirror Holder, Washer and Nut are included.
[ITEMS TO BUY TOGETHER
Products to be installed on Mount bar.
If you purchase the products you want to install at the same time, such as a power supply outlet, Smartphone Holder, Drink Holder, Camera Mounting Holders, etc., you can proceed with the work at a stretch.
Opinions and requests to Manufacturer.
Ideas products are different from other car products.
From now on. Good products at affordable prices. Thank you in advance.
View detail
TANAX OFFSET HOLDER 45
125 years old, 125 years old, 125 years old.
I want to know more about this.
I bought the genuine Monkey 125 side mirror because I couldn't see the rear clearly.
After installing the offset holder, the mirror viewing angle will be good, allowing you to see what's behind you and drive safely. -------------------------------------------------- -------- The side mirror of the genuine Monkey 125 was purchased because it could not show the rear. After installing the offset holder, the mirror viewing angle is good, so you can show the rear so you can drive safely Powered by Google Translator
View detail
How can I use this...
The bar was installed in front of the handlebar, and I honestly wondered what I should put on this part.... I installed the Smartphone Holder in the opposite direction, and the position of the Smartphone Holder looked good, but this time, it was attached to the bar so that the area around the Meter could not be seen by the bar, I was agonizing over how to make the best use of it, but I decided to just put it on for the time being. View detail
I like it! I'm curious about some things.
Originally, I bought it as a countermeasure against Throttle's Wobble.
Look what I got.
I'm not sure I'll be able to get a gutter on this thing.
So, installation
2 dowels are designed to prevent the Throttle from contacting the Switch box, and the Ring does not need to be attached. (It is possible to put it on by making a cut in one place, but I don't think it makes sense.)
So only Seat is used.
The result is so good! I feel sick every time I twist Axel. (Compliment)
However, there is also Demerit, and after a few twists and turns, Seat's
Konnichiwa!
I may hang on to the installation as I do so ….
View detail
Instead of a simple crucon (put it on the bottom side to restrictor?)
There is also a Throttle locker that is held in place with the palm of the hand, but this one can hold the Throttle in place, which considerably reduces the burden when running at a constant speed.
Since the throttle does not return simply by releasing the hand, it can be dangerous without a certain amount of skill, but if the closing motion is made consciously, the degree of opening can be adjusted in increments of about 2 to 3 km/h.
When attached to the lower side, the Throttle opening is (can be) restricted, so it may be used in place of Restrictor.
(useful for breaking in, etc.?)
If the grips are thicker, the attached silicon band will be large and sturdy without it, but since it rubs against the grips, it is recommended to wear it to reduce abrasion.
View detail
Back MirrorImproved rearward visibility
The rearward visibility of the Grom OEM Mirror was poor (about 1/3 of the arm was reflected) and I had to retract my arm every time I checked the rearward view.
When we tried to install it as it was, it interfered with the Throttle Wire, so we had to loosen the nut that secures the Wire and adjust the angle.
The installation has improved the reflection of the arms considerably, though not completely.
View detail
I need to buy two
Quality and texture information The paint finish is clean and good It certainly looks good on the sense of use Product to Buy Together Product # BCM-10 Installation difficulty easy Perfect for cost performance and comparison monkey 125 WeBike packaging is always great, arriving in a week for delivery and packaging Advice Since the screw is in the forward direction, it should be installed after checking carefully If you install it incorrectly, the screw line may be disrupted and the package configuration is composed of one, so please buy two and save time and money Many people buy only one View detail
Buy.
If you fall often, be sure to put it on!
All the Motorcycles in my house have them.
I've never broken Clutch or Brake.
View detail
Fits: Others , HONDA MONKEY125, HONDA CL250, YAMAHA XSR125
The clutch cable looks nice.
The original version of Monkey is covered with a cover, so it is plain. I searched for parts to give it a point. I was looking for a color similar to the mesh hose connection part, and I happened to find a red-blue Takegawa cable adjuster. I am very happy because it matches well with the mesh hose and gives the plain clutch cable a more stylish look. -------------------------------------------------- -------- Monkey's genuine is covered with cover, so it's flat. I searched the parts to give points. I found a color similar to the mash hose connection, and I found Red Blue's Takega and Cable Eraster. Powered by Google Translator View detail
![[Replacement] Pivot Perch FP / Bolt Set](https://img.webike-cdn.net/catalogue/11329/ZE43-9399_TS.jpg)
I appreciate the Large change to get Repair.
Some Zita products have soft screws that are easy to lick, but since it is difficult to replace the Bolt with a home center or similar product, I am thankful that a large replacement product is available. View detail
This is a good one!
I bought it because the one I had on two years ago was getting ragged.
I used to put it on with a Gas burner to burn it at a distance, but I still prefer Heat gun.
Dryer would have to be very powerful to make it work.
I use it to prevent deterioration of the Grip heater from UV rays and to reduce vibration of the Handlebar.
When I ride my Motorcycle in the middle of winter, I use light gloves because I am a Grich + Cover.
Even in that case, many are more than warm enough to both protect and warm the grich!
View detail
It is a product that fits very naturally.
Since it hasn't been installed yet, I'll replace it with a photo of a club member. It matches as if it was originally installed by the manufacturer. Both build quality and materials are excellent. I first heard from a club member who installed it that rust does not form even without the bolt cap. It is heavy and feels solid. Very satisfied.
-------------------------------------------------- -------- It is still installed, so it is replaced by a member of the club members. It suits the manufacturer as if it was originally mounted. Both builds and materials are great. First of all, I listened to the members of the club. The weight is too heavy, so I feel hard. Very satisfactory. Powered by Google Translator
View detail
Fits: TRIUMPH TRIDENT 660, TRIUMPH STREET TWIN BONNEVILLE
For those who do not like Bar end mirror
The OEM Bar End is one size smaller than the OEM Bar End, but the size and feel are the same. The quality of the Bar End is so good that you will feel like you have replaced it with a new one. It takes about 2 months for delivery, but it is worth the wait because of the low price. I bought the babyface one, but I prefer this one. View detail
Since the Handlebar was disconnected.
Due to cutting the Handlebar of the Racing Handlebar Kit (for installation of Lever Guard) It became necessary! There are a variety of processingParts to help. View detail
If you want to use only Course
When I was riding KLX230R on Course, the Rubber at the base of the Handlebar was inevitably distorted when I fell over, and the Handlebar position became wrong.
Instead of the OEM Rubber, an Aluminum conical collar is inserted and rigidly fixed so that the Handlebar will not be misaligned when tipped over.
Instead, there is no rubber, so vibration and shock will be Direct. It is a question of whether or not to replace it for touring on public roads, but it is OK if it is considered to be for course use only.
View detail
Excellent quality
Really good quality and nice paint. Does what it says on the tin. You can buy different bar holders and they will fit. Thanks View detail
Fits: YAMAHA TZR50, HONDA NSR250, YAMAHA XJR400, YAMAHA RZ50, KAWASAKI ZEPHYR750, KAWASAKI ZEPHYR400, HONDA NSR50, HONDA CB400SF, HONDA NS-1
Easier to adjust.
I bought it because I thought it would be easier to adjust by making the Screw part larger.
Satisfied with the results, as they are easier to adjust.
View detail