Reviews
Installation is very easy.
This will be the Saddle Back Support on the Right Side of the vehicle body.
The Saddle Back Support is an exclusive design jointly developed by Kawasaki and DAYTONA. The quality of the product is so high that it could be considered an OEM product, and it looks as if it were standard equipment from the start. The installation is easy. The back capacity is 12L at most since it is on the Left Side of the car body. It seems that 15L or 18L can be installed, but the distance from the exhaust system is 50mm for the manufacturer's recommended 12L.
Considering the future replacement of the exhaust system, I still think it is correct to secure a spacing of 50mm.
View detail
Truly Exclusive Design
It will be a Saddle Back Support on the Left Side of the vehicle body.
The Saddle Back Support is an exclusive design jointly developed by Kawasaki and DAYTONA. The quality of the product is so high that it could be considered an OEM product, and it looks as if it were standard equipment from the start. The installation is easy. The back capacity is 22L at the most because it is on the Left Side of the vehicle body.
View detail
Fits: SUZUKI DL1000 V-STROM1050XT, SUZUKI DL1000 V-STROM1050
Using SW-MOTECH's Tank Bag
I have used SW-MOTECH's Tank Bag on other cars and wanted to use it on the GSX-8S.
The OEM Tank ring was to be released in July 2023, but it looked like it would go on as is, so I bought it.
Installation was not a problem.
View detail
Exclusive product with excellent cost performance and neat appearance !
Installed prior to purchase of sorting bag.
Therefore, the feeling of use and durability will remain to be seen,
First of all, I was satisfied with the high accuracy of the installation and the simplicity that can be tolerated even without a bag.
View detail
Stability as expected
I'm sure it's being developed ahead of time to some extent.
It would be very nice to see car model-specific PARTS available sooner rather than later.
BoltQuantity for installation:Since there are only two PCs, there is no need to hesitate.
It is important to note that OEMBolt is the OEM Color and Quantity:The resin cover is fastened with a set.
Leave the OEM Color as it is and replace only the OEMBolt.
We use the 18L Daytona Waterproof BagDHS-32.
At the beginning of the installation, I was concerned about the long, rearward skimming with the car body.
If you take a closer look at the bag, you will see that it is quite a bit like a blinker, sass, and limit, so I think the largest limit is here.
I drove on the highway and had no problems.
I was given the opportunity to see it running on Winding from behind.
It seemed to be particularly stable without any sagging.
The price is reasonable, and I think there is no harm in buying it.
View detail
No ruggedness.
I haven't run with the side bag yet, so I'm not sure how I will feel about it, but it looks neat because it is a thin Pipe.
I like the fact that the angle can be changed freely, and I think it looks not tacky (in my opinion) without the side bag.
View detail
Fits: YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR250, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100, YAMAHA DRAGSTAR1100Classic
Quantity:Pair (for Left and Right) Might we need it?
Necessary to prevent Side Back entrapment.
It is easy to install.。
Required when installing Side Back on American without load capacity.
Accident prevention.
The other side is also needed.
View detail
Installed in 2023 MODEL.
Since the MODEL has been changed from Mounting Boltm6 to m8 since 2022, a little modification was necessary. View detail
Tank LockBag is convenient to use
I used GIVITank LockTank Bag in FJR. As you know, it is very useful because it can be detached with one-touch, so I do not have to take it off when I take a break. This time, I added a CRF250L to my CRF250L, and although I can install it on the RALLY50, I cannot install it on the L. So, I decided to use the Tank LockTank Bag. Therefore, I purchased this product in order to use Tank LockBag as a seat bag. View detail
Exclusive products are still good
I had been using Universal Product's triangular side bag support, but it could not support the bag I had installed and the bag made contact with the Tire, creating a hole, so I had to install a larger one.
I did not want to spend a lot of time to select one of the many Universal Products, only to regret it when I tried to install it and had to choose a different one. I have already forgotten how many times in my life I have lost money by buying cheap products.
The large size is necessary and sufficient, and it does not change the appearance of the cool XSR700. The strength is also perfect.
My car is mat color, so I sprayed Primer surfacer and painted it matte black.
I'm satisfied
View detail
Fits: BMW R1200 RS, BMW S1000XR, BMW R1150RT (02-04), BMW R1150RT, BMW R1200 15-18, BMW R1200 R 15-18, BMW R1200GS ADVENTURE, BMW K1200R (05-08), BMW K1200RS (00-04), BMW K1200S (05-08), BMW K1300 R 09-18, BMW K1300 S 09-18, BMW R1200GS, BMW R1150R (01-06)
The picture is different.
I wanted to purchase this bag at the same time as the SHAD bag, but was hesitant to purchase it because the picture on the site was different from what I had researched, so I purchased it at another store. The part number of the item I received was the same as the webike part number.
R1250RS was just a Type to replace 4 Bolt of Fuel tank cap with Pin. if you can understand Double nut, you can easily work with 2 M5 Nut.
View detail
Hepco&Becker C-BOW
Installation is very easy and can be done by anyone with tools! No special modifications are required! View detail
This is for Large type box!
It can be mounted on MT-09GIVIFitting for Mono Rack without any modification. I had been using the B47Series on a narrower UniversalBase, but recently it started to rattle. I have changed to this WIDEBase and there is no more rattling at all.
We felt that WIDEBase is still more stable for Large type boxes.
View detail
Used for YAMAHA BOLT Shoulder Bag (2022)
Bag Rail is also made by KIJIMA.
I wish the distance from the suspension was a little closer, although it is unavoidable for safety reasons. Also, the back of the Bag hits the apex of the Support's Curve section and does not hit it straight, so it is slightly slanted, and the Mounting Bolt should have been Black.
I have written a lot of complaints, but it is a good product at a reasonable price.
View detail
Fits: TRIUMPH Bonneville bobber, TRIUMPH Bonneville Bobber Black
KIJIMA is a reliable manufacturer.
Although there is always a concern that products from overseas PartsManufacturers may have problems,
I knew that KIJIMA, a Japan-based company, had no problems at all with their products.
It is very reliable.
View detail
Why OEMAttachment, Honda, get a grip!
Honda Genuine Accessories.Side boxBracket installation was the worst.
I had heard that a person who purchased the product at the same time had found the installation to be Large strange.
I didn't think it was this Large strange.
In the end, all three stop bolt holes were machined to length.
When we checked the position of each of the three pcs, we found that they were off by about 2mm to 3mm.
All three holes were to be machined at least 1mm long,
It is made so sturdy that my Hand power was not flexible enough.
It took me about 3 hours, and I was cutting long holes little by little, believing that it was OEM, but in the second half I was using Leutor to do the hard work.
Finally got around to installing it.
I was worried about the future as I have other OEMAttachment purchases.
View detail
C-Bow
[How is it used?
For Touring
Was the one you received as per Image?
It was just like the image.
Was the installation difficult?
it's simple
How was your experience with it?
Only driven once, but not bad.
[Included Parts:were they on?
Washers, screws, etc. for installation are enclosed, and they are used to fix the unit in place.
[Was there anything that disappointed you?
Not sure yet, but so far none.
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
View detail
Fits: HONDA CRF300L, HONDA CRF300L RALLY, HONDA CRF250RALLY(S), HONDA CRF250RALLY, HONDA CRF250L(S), HONDA CRF250L
Pipe feels thick and firm.
It could be used with DAYTONA's Grab Bar Carrier.
However, Bolt needs a long one.
View detail
Available in Bag RailSingle Item
[How is it used?
As stated in the instruction manual, this product is designed to be used with Bag Support, which is sold separately.
But what I wanted to do was not to add a big Saddle Bag, I just wanted something that could be used like a Grab Bar to make it easier to load the Rear.
Therefore, we do not purchase Bag Support and use it as a Single Item.
Was the one you received as per Image?
The stick came as per Image.
Was the installation difficult?
Very easy. Even a child could work on it.
How was your experience with it?
It is very good, although it is used for other purposes from KIJIMA's point of view, because it is well made.
[Included Parts:were they on?
Yes.
[Was there anything that disappointed you?
No, there is not.
Point and hang of installation
I would just remove and replace OEM Product.
In my case, I do not use Bag Support, so the M8x75 supplied with the product is not long enough to hold the Bag RailBody in place (the OEMBolt is not long enough).
I think it is a good idea to have one, but it needs to be fixed by adding a spacer.
I was rifling through my toolbox to see if I could find anything good, and I found Nproject's Waist Color Set for M8 Found the
This was just a bingo.
[ITEMS TO BUY TOGETHER
If you want to fix a Tool Bag to this thing! If you are thinking "I want to fix my Tool Bag to this thing!
Helmet Lock Relocation Bracket would be available for OEM Helmet locks if purchased.
View detail
Unobtrusive parts, but very useful!
I purchased one of these BackRails to attach a Tool Bag and Accessory Case on the Left Side.
After that, I purchased and installed these Parts for Right Side as well, since they seemed to be useful in various ways. (Common For Left/Right Side.) 。
When using Luggage Net, the position and balance of the Net can be adjusted,
It is easy and convenient to fix Net without using Hook.
I have a Rear Carrier installed, and thanks to this Rail, the luggage Net does not interfere with the Rear Fender!
This BackRail is designed to be used in combination with the Side Bag Support, so if the BackRail is installed only, a commercially available Spacer will be required separately. (It is the difference between a Bag SupportBody Spacer or a stand-alone Spacer) 。
It is good that it is unobtrusive and unobtrusive. It is very useful and cost-effective.
Thank you, KIJIMA, for your product development.
View detail