Reviews
Actually, it's FOR Motorcycle. (Lol)
The outer diameter of the Handlebar Pipe is Φ22.2, which is a common standard size, and the low screw part is used for bicycles.
Back Mirror of a hand-held CUB was installed.
The product has a slightly thin coating, but the quality is reasonable for the low price.
For those who want to reduce the height when installing Back Mirror
I can recommend it.
View detail
Wow, that's expensive!
The product is great, but not quintessentially expensive. View detail
Greater scope for adjustment
Replaced the mirror at the same time, which was a bit tricky since I had to position the Offset and Mirror at the same time, and since the Brake Side was going to interfere with the Cable, I used the OEM Spacer. I used the OEM spacer because the Brake Side was going to interfere with the Cable. View detail
To prevent interference
No interference with Mirror replacement at height. View detail
Offset
Good to move Mirror forward. View detail
Custom
I have not installed it yet, but I am satisfied with the product. View detail
Mirror Holder is no longer available.
[How is it used?
I bought a used WR250R before the price went up as much as it has now, and it had a ZETA Pivot Clutch Perch CP installed at first, but the Mirror was only installed on the Right Side, so I had to replace it with a ZETA Pivot Clutch Perch CP. Is it legal to use a LargeMirror without LeftMirror, or is it scary when changing lanes?" I looked closely around the clutch and found that the ZETA clutch holder does not have a screw hole for mounting Mirror!
The OEM clutch holder of the WR250R has an integrated Mirror Holder, so when it was replaced with a ZETA one, the Left Mirror could no longer be installed.
I ordered this product as soon as possible to avoid danger, as my driving skills and ability to perceive danger are not very good.
Did you receive the item as per the Image?
I ordered the product after thoroughly checking Webike's product description section, and it was exactly as I had imagined it to be.
Was it difficult to install?
BoltQuantity this product to the space in the root river of the Clutch holder attached to the Handlebar.:It is a simple job to attach with 2pcs.
Quantity:Pair (for Left and Right) If the Mirror mounting spacing of the two mirrors can be installed at the same location, there will be less discomfort when the Motorcycle is viewed from the front.
How did you like it?
Once firmly installed, the Mirror Holder is a normal Mirror Holder without any Mirror gaps while driving.
When I purchased it from Webike, it was on sale at Timing, so I was able to purchase it at a lower price than OEM holders for other vehicles.
Was "Included Parts:" attached?
BoltQuantity for HolderBody and mounting:2pcs are included in the package.
Were there any disappointments?
I purchased a Blue alumite product and it faded faster than other Anodized dyed products.
I am thinking of painting it matte black with a cheap can of Spray if the color fades any further.
Other items that would be helpful
Point and hang of installation
As I mentioned above, I think it would be less uncomfortable when viewed from the front in Symmetry if the Holder is mounted at the same spacing as the Mirror position on the Brake Side.
[Availability and clarity of the Instruction Manual
I don't think there was an Instruction Manual...sorry my memory is a bit hazy as I purchased it quite a while ago.
[Notes]
There is nothing special in terms of functionality, but Blue alumite fades quickly, so I think it would be safer to purchase Black.
[ITEMS TO BUY TOGETHER
This is an opportunity to use your favorite MirrorQuantity:Pair (for Left and Right) I wonder if it would be customary to purchase a "Custom"?
[Opinions and requests to Manufacturer
The color fades quickly, so I would like you to take measures to prevent this, and I would like you to continue selling this product for as long as possible.
View detail
Mount expansion foundation with no gap required
[How is it used?
Used on the Clutch Side of CBR250RR (MC51) from April 11, 2020 to October 2, 2023.
Mount the iPhone miniSeries using the following parts
1.RAM MOUNTS BallMount M10xP1.25:https://www.webike.net/sd/24021956/
2.RAM MOUNTS Short arm:https://www.webike.net/sd/21313052/
3.RAM MOUNTS XGrip (M) Smartphone Holder (maybe):https://www.webike.net/sd/22558592/
4.Large amount of Screw Lock agent
Was the one you received as per Image?
The product is exactly as shown in the image.
Was the installation difficult?
I forgot to measure the distance between Bolt.
BoltQuantity:I guess it's easy enough to remove and replace the 2pcs and install. Since I feel there is a gap at the bottom, it may need to be filled with Washer or something.
How was your experience with it?
The Smartphone Mount is a good choice because it requires far fewer unnecessary parts than a dedicated bar.
Since it is installed by replacing the original parts, there is no need to consider the gap between handlebars, etc., unlike retrofit Mirror Holderet etc. The original bolt can also be used.
Smartphone mounting is possible with far fewer wasted parts than with dedicated mount bars, etc.
After mounting the ball on the car body, I shook it with the ball, and the car body shook, so it seems to be robust.
I don't remember how many times I actually ran with my phone on it.
Riding the phone on the Clutch (Left) side rather than on the Brake (Right) side met the request because I prefer the LeftMount for the possibility that the phone could escape to a non-roadway in case of an emergency.
[Included Parts:were they on?
Included Parts:None, only this product wrapped in Vinyl
[Was there anything that disappointed you?
I think I used a similar part from YAMAHA for the R6 Brake because of the similarity.
YAMAHA 5YU-26393-00:https://www.webike.net/sd/25729937/
That one did not occur when the gap was R6.
[Notes]
This product Mirror Holder It is used like the CF POSH Universal mirror holder (https://www.webike.net/sd/1125900/), but it does not say anywhere that it is for smartphone mount.
View detail
Cheap and affordable_OEM alternative
Something cheaper than OEM." I was looking for a Motorcycle supply store with the motto of
Although there are variants for Custom Ordinary." is not surprising.
I'm glad I found it on webike!
This is a great price for the front and rear parts and Screws included.
View detail
For brembo CORSA Corta MASTER
Installed on brembo CORSA Corta.
Looks.Material, good! (^^)
View detail
Buy with brake lever set change
The finish looks good and I'm satisfied with the design I want Recommended as a mirror hole replacement when changing the genuine front brake set View detail
For Radial pump master installation
I used this product when I changed my MT-09 to YZF-R1 Radial pump master cylinder. There are only a few Mirror Brackets that are compatible with Opposite Thread Screws, so I am glad that this product is available.
It would have been better if Bolt was in Black.
View detail
Required for Mirror installation on Racer
When running a foreign Enduro racer on public roads, the NORMAL does not have a Holder to install Mirror. Replacing it with this will solve the problem. View detail
Fits: その他
Cost performance good
Purchased as Mirror Bracket for bremboRCScorsacorta.
Coloring is also MATCH and no problem.
Also, there is no logo, and the shape is simple and good.
The price is modest and affordable.
View detail
I feel safe.
It gives me a sense of security. It was as expected, I use it for my SUPER CUBPRO. View detail
Unplug and replace Pin.
Remove and replace the Clamp Pin that is attached from the beginning.
It is Slim with a Fit feel because it is OEM, rather than the Mirror Clamp which is a retrofit. The color is painted the same as the Body color, so it feels very high quality.
If you do not have a pin, you need to prepare a hammer and a punch because you will need a punch when you pull out the pin.
It is Magura OEM, but I believe it can be installed on Motomaster as well.
View detail
Mounted on Right SideMirror
The entire Mirror seems to stick out a little more than in Normal, but this is good because it makes it easier to see the lane behind you and the passing lane. View detail
Mounted on LeftMirror
It is attached to LeftMirror.
I couldn't see the back of the Large half of the Mirror because it was hidden by my arm.
Now it is in full view.
The entire Mirror will be more protruding than in NORMAL.
If you drive without VANVAN of slip-throughs, you're good to go.
View detail
completely visible behind one's back
Installed on LeftMirror.
Although there is a slight sense of protrusion from the vehicle body, it allows me to see the rear of the vehicle, which was difficult to see with my own body, and it makes it easier to see how close the following vehicle is in town and to check on my companions when touring.
View detail
Thin.
I bought this because I changed the Clutch lever and no longer have the Mirror hole.
It is good because it is thin and one step higher, so it can be placed anywhere.
View detail