Reviews
Combined with the company's Universal Radiator Hose, it is a savior for old car riders.
The pipe itself is not made of soft aluminum or brass, but a solid iron-like pipe. The pipe itself is not made of soft aluminum or brass, but of solid iron, so there is no deformation of the pipe due to tightening of the band, and it can be tightened firmly, so there is no leakage even if pressure is applied.
The ends of the pipe are also thickened to prevent the hose from falling out, so as long as the hose band is properly tightened, the hose will not fall out even if pressure is applied.
View detail
Conversion of front brake hose to Stainless Steel Mesh Hose
The mesh hose I had was not long enough, so I used it to connect the hose to the Caliper, which I wanted to make the best size for the hose, including handling. View detail
Handlebar position changed, brake hose length increased.
The handlebar position of the Yamaha Bolt R-Spec is too far away, so I used the Handlebar Riser 2 Inch and installed the STD Handlebar. (Switch holes in place as they are) 、 2-inches (approx. 5 cm) I brought it to the front, and Position became much easier.
If the handlebar position is moved forward to the 2-inches maximum, when the handlebar is turned to the full Left position, the brake hose (and Accelerator cable) is fully extended and there is no room to spare,
Replace Brake hose with a longer one
・Brake hose joint (this product) Installation
and finally installed this product.
(At the same time, the Accelerator cable was replaced with a 15 cm longer one. HURRICANE:HB6471)
This product is a Joint between Reserver tank and Hose.
Air bleeding of the brake hose is required when installing this product.
This Joint is a Universal Product, so it can be used in a wide range of applications.
I would like to use it in this condition for the time being.
At any rate, the problem is solved and I am satisfied.
View detail
Used to connect to Vacuum gauge
[How is it used?
I bought this to convert a Vacuum gauge because the diameter of the Hose did not fit when I tried to install it.
I am satisfied with the use of the product, especially with no leaks.
Was the one you received as per Image?
Yes, it is Joint and Clip as shown in the image.
How was your experience with it?
I was able to use it without any problems.
[Points to note]
Not particularly
View detail
You need multiple Large bodies, so the result is a bit more expensive.
The inner diameter of the Fuel Hose is 4mm, and we could not find a suitable Fuel Filter,
The outer diameter of the Filter side was 5mm, so we converted the Hose of the Filter section.
It was made of Gold genus, seemed durable, and came with a Hose clip.
1 pc. seems cheap, but I think I will have to buy more than one because I need to convert it back after converting it with Large body Pattern.
View detail
Sub tank to carburetor for connection
I bought it because the hose diameter of the Sub tank was different from that of the carburetor.
Now you can connect to the Sub tank and carburetor without any problems.
View detail
Texture is GOOD
The Blowby hose of xr1200 is 5mm and the Breather Hose 650mm 6mm Diameter of DAYTONA is 6mm, so it was purchased for conversion.
There are other plastic ones, but I chose this one in Aluminum because it looks cheap and I did not know what would happen with the heat exhaust from the Engine.
I was concerned that the exhaust heat would affect the Aluminum and be bad for the Hose, but well, we'll just have to wait and see.
I also liked that it came with a Clip so I didn't have to buy an additional one.
View detail
-- KITACO: -- hose JNT/RED 5-6 product-number: -- 993-0005060 -- merchandise information goods details hose joint (5phi->6phi) RED
-- KITACO: -- hose JNT/RED 5-6 product-number: -- 993-0005060 -- merchandise information goods details hose joint (5phi->6phi) RED View detail
I used it to connect to Fuel Cock.
I used this product to connect to the Fuel Cock, which was a big help because the area near the Fuel Cock was too narrow for the Straight Type to fit! View detail
Convenient, but...
I use it on the hose of the fuel tank of my CBR250 MC17. it is convenient to remove the hose with one-touch while lifting the tank during maintenance. The only drawback is that it is too expensive. View detail
Convenient Hose
Introduced because OEMHose is not long enough for the Clutch master change.
It is a grateful product that lowers the threshold of MASTER exchange at once.
Eventually, I'm planning to redo MASTER to Release, but for now, I'll go with this.
View detail
Used to branch the Hose
I used it because I needed to change the handling of the Hose when I replaced the Radiator-.
I used it mainly for the part of the Hose that branches out, and it has been used without any water leaks.
If I had to say, this Joint itself has a Large size, and I felt that it is quite heavy when I installed it.
View detail
With Stainless Band is a nice touch.
The material is Stainless Steel, so it is a little heavier than Aluminum, but it is also rust-resistant, so it is safe for the water area.
The performance is perfectly fine, but I'm more than happy to see that it comes with two Stainless Steel Bands. It's a hassle to buy just the Band separately …
View detail
Used in Fuel Sub Tank
Webike Garage We used it in Sub Gas Tank 1L for Tuning of BigGarage.
Since the diameter of Fuel Hose of ZrX 1200 R is 10 mm, the diameter of Hose on the side of Suub gas tank is 6 mm, I bought a commodity for conversion.
It is good for Gasoline as well as strong enough to be used for a long time but good product is a little bad Image Cost.
View detail
Since the bores of a Hose differ by the Gasoline cock and a carburetor in many cases when carburetors are exchanged, it will be saved if there are such products.I want it to write in a description etc. which to be the life of this product made of a Nylon.
Since the bores of a Hose differ by the Gasoline cock and a carburetor in many cases when carburetors are exchanged, it will be saved if there are such products.I want it to write in a description etc. which to be the life of this product made of a Nylon. View detail