Reviews
For Meter Bulb in 6V vehicles
When I went out shopping at night with my Yamaha CHAPPY that I had restored, I could not see the Meter at all and thought it was out of bulbs, so I immediately purchased one.
YamahaOEM Parts are still available, but at a slightly higher price.
I looked up 6V3W and found this product, and since it was inexpensive and in stock, I snapped it up.
10mm BoltQuantity fixing Meter:Remove the 2pcs and the meter cable to access the wiring.
I replaced it and put it back together, and when I started the Engine, the Meter Bulb came on successfully.
Since it is 6V, it is naturally dark, and to be frank, you can only vaguely see the position of the needle when driving at night.
I don't plan to go far, so I'm satisfied that I can see for now.
View detail
Japanese Vehicle Inspection Correspondence
Before the inspection of SR400, I went to the tester place off site to check the light intensity. I had to go back and forth to Tester two years ago, but they did it without any extra charge, I switched to the new Stanley Hyper Halogen LightValve, which I brought with me again. It is just 150mm away from the specified light level, but it is OK.... Hyper Halogen Light is a high efficiency valve and can be brighter with the same power consumption as the standard valve, but it seems to have a shorter life. View detail
LED Bulb from leading manufacturer
Stanley is a leading manufacturer of OEM parts.
I am satisfied with both the brightness and the spread of light. The picture was taken with the position lamp in place.
The original brightness of the Valve is brighter than the image because the brightness is set to low.
View detail
Normal is fine.
Tail lamps that are always on are consumable.
Stop-lamps are still alive but replaced immediately when noticed to avoid maintenance failure due to trivial things.
We had thought about using LEDs, but we concluded that Standard was the best choice due to its cost performance and reliability.
In the case of DJEBEL, the OEM installed Carrier interferes with the approach of the Tail lamp cover to the Screw. This is where SEA BASS comes in:remove the rear screws from the carrier, loosen the front screws, and stand the carrier up like a Gal wing, and the replacement can be completed in a few minutes.
The durability of the bulbs is a matter of luck, but since it is a product of FOR JAPAN MODEL MANUFACTURER, it is safe to use for the time being.
View detail
For Stock
I have already purchased this product last time and bought it for Stock.
It's for old Custom parts,
In the countryside, items are difficult to obtain.
Thanks.
View detail
Tail lamp replacement for JOG for repair.
Tail lamp bulb of a 2-stroke JOG obtained through a private sale was broken and was replaced.
Lower price than Valve for OEM Parts, Quantity:1 Set of 2pcs.
I will only use 1 pc. and will keep the other one as a spare.
I thought about using LED Tail lamp bulbs, but since it is a 50cc moped, these are sufficient.
*Wattage should be matched to the OEM.
View detail
A very ordinary Halogen bulb.
Whenever I buy a used Motorcycle, I always replace all the valves with new ones, but since they were out of stock at my local store, I couldn't be bothered to come back to the store, so I bought them by mail order.
I thought the price might be a little higher than the actual store. I thought the price might be a little higher than in the actual store, but considering the time and effort involved, it was acceptable.
There is nothing wrong with the fit and there is nothing special to say about the color.
This is fine unless you don't want the Amber color to stand out over the Lens.
I thought it might be a good idea to purchase an additional one as a spare when I purchase some more Parts.
View detail
It was saved.
Large European blinker bulbs that were installed a long time ago were out of stock at home centers and car shops in the countryside, and there were no hits in the Internet search.
However, I loosened the search criteria and found it! Crying
Thank you for the help
I'll stock up next time.
View detail
It is safer to always have it at home with Spare!
The cheap Pine Stripe bulbs, but just one of these can cause a maintenance failure!
They run out without notice, so it's always safer to have one in reserve.
Depending on the model of car, the replacement work is a single +Driver.
View detail
Rare 6V bulb
I used it to repair a broken Neutral lamp on a VANVAN90 that was given to me by a friend's father.
Since it is an old motorcycle, there are no parts available, so the rare 6v bulb is a big help.
View detail
The abundant number of Watt will help.
I added Hazard and bought this one to lower the Watt number in terms of power consumption reduction.
It was really helpful to have Double Bulb as well as Single Bulb.
The abundance of Variation here is very good, as Motorcycle definitely does not look good with flashing LEDs.
View detail
Cost-effective
Used for POSH and Fath blinkers. POSH has Valve, but I bought this one because Mats Stripe products are much cheaper even though they are the same standard. I have used them on other cars and have confirmed that there are no quality problems, so I can use them with confidence. View detail
Fits: KAWASAKI KSR110, KAWASAKI KSR110, HONDA PRESS CUB 50 DELUXE, HONDA PRESS CUB 50, KAWASAKI KSR110, HONDA SUPER CUB 50, KAWASAKI SUPERSHERPA , KAWASAKI SUPERSHERPA , HONDA SUPER CUB , HONDA SUPER CUB Custom, HONDA SUPER CUB 50 Custom
turn filament
Acquired for HONDA SUPER CUB 50 CUSTOM.
Part number No.86, manufacturer STANLEY.
Excellent lamp, everything came up. STANLEY quality is excellent.
Great lamp, everything came up. The STANLEY quality is excellent. -------------------------------------------------- -------- Acquired for Honda Super Cub 50 Custom. Article of the details No.86, manufacturer Stanley. Great lamp, everything came up. The quality of Stanley is excellent. Great Lamp, EVERYTHING CAME UP. The Stanley Quality is Excellent. Powered by Google Translator
View detail
PS250 [Color] Used for pre-blinker for clearing
Blinker cover for PS250. [Color] I bought this product because I had to replace the Orange bulbs to make them Clear. I bought this product because I had to replace the Orange bulbs with Orange bulbs to make them Clear. I think it is worth the cost. View detail
Convenient Quantity:Set
CT110 HUNTER CUBCT110, purchased for 12V conversion.
It is a very nice product because there is no need to examine them one by one.
View detail
For a certain Blinker's High flasher countermeasure.
I bought a 10W one because 8W makes it a high flasher.
It worked.
View detail
Replaced with Valve here as I had PS250's previous Blinker coverClear
I bought this one because one of my beautification plans for my used PS250 was to stop using the Orange color for the Blinker cover and replace it with Clear, but then I had to replace Valve with Orange. Yes, it's a waste of time. It's a waste that I can't use what I have so far. I could have replaced it with LED Bulb anyway, but then I would have had to replace the Blinker parts (I forgot the name of them). Also, I don't dislike the fact that I can see a little bit of orange color through the transparent cover, and it gives the car a nice, modern look.
However, unlike a moped, the Valve had to be inserted horizontally, so it was somewhat difficult to do. The work was easy and it took only 10 minutes to replace 4 valves.
One thing I wondered is that the front Blinker is 23/8W since it also has a built-in Position lamp, and the back Blinker is 23w, but the front one is less expensive and the back one is more expensive. I would understand if it was the other way around, but why is that?
And previously, Clear cover and Valve were Quantities.:It looks like it was sold as a Set, but it seems to have been discontinued.:I would be more than happy if they were sold at a discount at Set.
View detail
BENLY50AA05
Used for Meter Bulb of Benly50AA05.
OEM is 1.7W, but it is now 5W and brighter.
View detail
For Meter Bulb
I purchased this for my 4LMONKEY Meter Bulb.
If you like the old-fashioned way, this is the way to go, as it is not as flashy and bright as LEDs.
View detail
Good
I used them because my interior light had run out of bulbs, and the brightness has not changed at all and the quality is absolutely fine.
Since it comes in a pack of two, I can keep it as a spare and replace it when I run out of balls again.
View detail