Reviews
Reliable Brand
Purchased due to the addition of a Large Motorcycle.
We use Chinese STAND for 125 and 400 Class Motorcycles and this one for Large Motorcycles.
With Chinese STAND, the STANDBODY is distorted by the weight of the car body when it is lifted up, but this product can be lifted up stably without any problem at all.
If I had to make a request, I would say that protective parts should be attached to the pipe that touches the ground when lifting up, otherwise the STAND will become wound wound.
View detail
Fits: HONDA Rebel1100, HONDA Rebel500, HONDA Rebel250
It's tough to go it alone.
If two people do it together, there is plenty of room, but alone it is quite scary.
If you have a Rear Carrier with Grab Bar, you may be able to do it by yourself, but it is very difficult because the REBEL is low and there is no part to grab on the Rear side.
I did it with two people at first to make sure I could do it, and then I tried it alone, but I almost beat him.
I think it would be wrong to object to the fact that it cannot be done by one person, since the Manufacturer recommends a two-person operation in the first place.
Motorcycle maintenance is basically a one-person job, so I felt like Minus in that I had to get help every time!
View detail
The product is good, but..,
The quality of the product is very good, as it is made in Japan. However, the contents of the package, especially the tires and other components, smelled like cigarettes and filled the storage room. It is a pity because the product is so good. View detail
Questionable quality inspection of products
I received it ahead of schedule, but when I was setting it up for installation to fit my Motorcycle's size,
The Clamp's corner Pipe was not penetrating the ArmHolder's insertion hole (One Side).
I had no choice but to use a slotted screwdriver as a chisel to remove the BALI.
DAYTONA, please inspect your products carefully.
View detail
How about one for Garage?
I purchased this product for the first time for Chain Maintenance.
I was nervous when I put it up for the first time, but Quantity was there without a hitch!:Set is ready.
It is so convenient that I wish I had introduced it sooner.
I am satisfied with the quality of the product, but I have one point,
The hook part was bare gold and it looked like it might scratch the Swing Arm,
I covered it with Fuel Hose, which happened to be available.
Other companies' MAJOR products have already taken countermeasures in this area, so please check this when purchasing.
View detail
Fits: SUZUKI V STROM 1050, SUZUKI V STROM 650
Some parts are pricey, but no problem.
Chain and Wheel cleaning was inconvenient and price.
Buy this one which is Reasonable.
Assembly is required, but the height can be adjusted without any problem. The Hook and the Adapter for direct use of the Swing Arm are included from the start. I purchased a ZETA Swingarm Spool at the same time and used the Hook for its stability.
When using the STAND, hang the vehicle straight with the front brake applied →STAND on the Hook →STAND rearward tip down, and you are done.
Note that there is no Cover on the Hook, so I made a mistake at first and damaged the Swing Arm as much as I could….
There is no wobble, and the feel is satisfactory. Above all, I am satisfied with the maintenance performance of the Large width up.
View detail
Slightly disappointed.
[How is it used?
Used in YZF-R6 (2019) with V-receiver.
I am new to buying Rear stand but have rented a Short from J-TRIP.
Was the one you received as per Image?
It was heavier than I expected, but not a problem at all.
The large size was as shown in the image, but it is still large compared to the short size.
How was your experience with it?
It is easy to raise and lower, and although I was worried about the short version, I made the right choice by choosing the long version.
However, even with Short, Stand for Beginner was easy and did not require much strength.
The screw holes are too large or the bracket is wobbly even when the bolt is tightened firmly.
[Points to note]
In the case of the V receiver, even at the lowest setting, it floats about 4 cm, so a little force is required to raise it.
If you want to raise it with light force, it is better to choose Stand for Beginner because Stand for Beginner will be in a lower position.
View detail
Fits: HONDA Rebel1100, HONDA Rebel500, HONDA Rebel250
DAYTONA
I'd like to see it built a little sturdier. View detail
It can be used, but only in Large size.
Cost performance is sufficient. However, care should be taken when using it on heavy motorcycles. The clearance of the support part is large, so it will be slightly slanted. We own an NSR250R and an NSR50, and it can be used for both. Both vehicles are lightweight, so even if it is skewed by hand, it can be corrected. View detail
Hard to buy, bulky, frequency of use
First of all, as a premise of Large, it is difficult to purchase OnLine anyway.
If you are a beginner, I would recommend Unit or DAYTONA products as there is a normal chance of buying the wrong one.
There's nothing in particular that makes it superior because it's a J-TRIP. I think it's almost like everyone just buys it because it's the only one they know.
There are a lot of maintenance stands overseas that are very well made, but they are all bulky, so the cost of transporting them tends to be high, and the selling price is not cheap either, which is a difficult thing for an island country.
View detail
U-shaped hook
I know it's a series of pitches, but I installed the RIDEA RIDEA Stand Hook yesterday and used it with a U-shaped hook.
It's more obvious than Swing ArmType, but it's totally stable.
However, it interferes with the bolt for hook fixation when the shaft is removed.
I removed the Bolt at that time because it won't come off once it's fixed in STAND.
U-shaped hooks can be used normally, so this is more PointUp than the last one.
But I still think it's too hard for a car with a lot of weight.
View detail
No V-receiving Rubber!
Purchased at the same time with Aluminum Hook Bolt for NINJA1000SX
Adjusting the width, the first time the rubber breaks and scratches the swing arm..
I think we need a little more room to play
The performance itself is not a problem, but the Hook bolt or Y-type rubber strength needs to be improved
If you're considering buying one, you can use Tape to cure the Rubber and Swing Arm before use You should either cure it or make it L-shaped
View detail
Cheesy
I bought it a few years ago and I think the quality is poor for a JAPAN
The paint is weak, rust easily, and the plating of the receiver is also weak Also the welding bead is dirty and expensive
View detail
sufficient for one's needs
It's a good thing that the hooks can't be shared with other companies' products It is
The paint peels off and rusts and becomes unsightly as you use it, so this is a rust-resistant material:I hope it's Stainless Steel, although it looks like the Plating one came out It's expensive and this one is sufficient
View detail
It's a shame because it's a manufacturer's product
I don't think that only a well-known manufacturer can ship a product in a dirty condition
There was something black and sticky like a tar on it and some of the paint was peeling off
Probably not from the manufacturing process, but from the packing process
I was convinced that it wasn't worth returning or exchanging, and that with use, it would get dirty and the paint would come off has lost confidence in it
View detail
I think this quality is good for the price!
I think the quality is good for the price
But it seems to be too much for a car with a large chassis
Just right for MT-03
Brake, Chain, Sprocket, etc
I think it's necessary for those who make maintenance better
I'm not using the Front
It looks fine
View detail
Is the price high?
Even when compared with MaintenanceSTAND about 3,000 yen
The difference is that Roller is doing it properly. Ease of use has not changed.
I feel like I lost something.
View detail
There is neither impossible nor impossible, but the price is too high!
I bought it with Front stand. Because the price is high, I bought it very much until I purchased it
JAPAN so I decided w It was my mistake in choice but supported the car body with Left hand Right When I hooked by hand, the Short Type felt a bit unbearable.
View detail
If you do not carefully check the bearing shape - - -
It was a shape that bearings can not be used with real cars - -
I bought it by fishing in Sail, but it became a chance to purchase additional bearings.
I think that it is a good product only if I pay attention when buying it.
The Bubble stop Rubber Band creates a sense of Cheap very much.
View detail
There is no choice because there is only this!
While thanking you for making it exclusively for DREAM 50, some points.
I am using it when exchanging Oil or Maintenance of Chain, but I need a little courage and hang to be able to ride alone.
After that, according to other people 's Review, Spolcket' s Bolt interfered quickly, Plating half Pipe (Protective Pipe?) It is easy to peel off.
But I am thankful that you have sold it with exclusive items after all.
View detail