![icon-webike.png](https://thimg-afcc.kxcdn.com/@wth-shop/assets/desktop/img/icon-webike.png)
Reviews
![Vacuum Piston 40mm for CV](https://img.webike-cdn.net/catalogue/images/115332/115332_L021130_TS.jpg)
Fits: HARLEY-DAVIDSON Fits OEMCVCarburetor
No installation problems after a little sharpening.
The surface treatment of the slide valve seems a little rough, the OEM was the same, so no problem.
Because the negative pressure presses the Slide surface Rear against the sidewalls, especially the areas that are strongly hit are polished and shining.
If the corners and flat surfaces of the PAL blade wings are polished with a gold-based polishing compound and installed, the initial sliding will be smooth.
View detail
![Carburetor Air Screw Adjustments Tool for HONDA D Type Straight Type](https://img.webike-cdn.net/catalogue/13454/tool317_1_TS.jpg)
PRO TOOLS D-type carburetorTool
I purchased a similar product from CHINA, but it was not only inaccurate but unusable, so I purchased this one.
It is a little expensive compared to similar products at 770 yen, but I wish I had purchased this one from the beginning because it would have been useless if I couldn't use it.
I had the impression that it was not in the category of high-end tools Brand, but I was satisfied because it had a good texture, was comfortable in my hand, and above all, the precision was neat.
View detail
![Carburetor Jet Driver 4-Types](https://img.webike-cdn.net/catalogue/18491/2525_TS.jpg)
Frankly
[How is it used?
I had been doing my best with the tools I had on hand when tinkering with the carburetor, but the driver I wanted to use sometimes went somewhere, and I thought it would be more efficient to have a dedicated tool for the job.
Also, a certain degree of Small Type is used for Quantity:I chose this product that became a Set because it seemed easy to use.
Was the one you received as per Image?
The size was just like the Image.
How was your experience with it?
It can be used so-so when tinkering with carburetor.
Since the tip is reasonably strong and well-made, you should be a little careful when removing adhering Jets.
Small Type is easy to use with a good Point and does not take up much space for storage.
I think it is better to put it in a bag to avoid losing it when storing it, especially since it does not come with a bag etc.
[Points to note]
Be careful not to lose it, as it does not seem to be sold in Rose.
How did it compare to other products?
We use KTC's driver for carburetor for Pilot Jet, but KTC's tip is still better made.
But, well, I thought this product would be sufficient unless you are working on an abandoned car, etc.
【Review】
If you are new to carburetor for now, you can use the Quantity:I thought it would be good to be a Set.
I am happy because I no longer have to select and prepare several Drivers for it when I play with carburetor.
View detail
![Carburetor Air Screw Adjustments Tool for HONDA D Type Straight Type](https://img.webike-cdn.net/catalogue/13454/tool317_1_TS.jpg)
Not much...
[How is it used?
Used to adjust d-type Screw
Was the one you received as per Image?
Yes
How was your experience with it?
Outer diameter is Large, Clearance is tight
[Points to note]
Not very well made.
How did it compare to other products?
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
![Carburetor Jet Driver 4-Types](https://img.webike-cdn.net/catalogue/18491/2525_TS.jpg)
It was easy to use.
When adjusting the Screw, it would be nice if the Driver had a sills. View detail
![Carburetor Bore Tool](https://img.webike-cdn.net/catalogue/10054/75252_TS.jpg)
Large sturdy even with narrow Jet holes
[How is it used? CarburetorMaintenance
Was the one you received as per Image? Almost as per Image
How was your experience with it? Easy to use
[Points to note] The thinnest Wire is the easiest to habituate.
How did it compare to other products? cheap
Other items that would be helpful
Points and hang for installation/Items to be purchased together/Opinions and requests to the Manufacturer It is recommended to use with Carburetor cleaner.
View detail
![Cab Pilot Screw Adjustment Tool Set](https://global.webike-cdn.net/photo/impression/1f/1fec67484c7ad231b82922949f7f406dL.jpg)
Because I went crazy when I overhauled it.
[How is it used?
The two deepest of the four shots can also be easily adjusted.
After closing off the screws, I put them back in, and since there was no memory, I made my own.
Was the one you received as per Image?
Yes
How was your experience with it?
I did it once without and the convenience was amazing.
Once you use it, you can't do without it.
[Points to note]
No Memory, so you need to do your own Arrangement.
How did it compare to other products?
unknown
Other items that would be helpful
Installation points and hang/Items to buy together/ Opinions and requests to the Manufacturer
View detail
![Carburetor Jet Driver 4-Types](https://global.webike-cdn.net/uiu/impression/202112/09_1019487_61b159dcdd140.jpg)
An advantageous tool that you can touch even after installing the fcr!
You can touch the pilot screw even after installing the fcr. It is a tool that fixes the acceleration pump and makes it easy to replace the main jet. My bicycle is w650. View detail
![Carburetor Bore Tool](https://global.webike-cdn.net/photo/impression/0c/0ca311e688148900681491c21f1e3ccfL.jpg)
Easy to use
I used to use hard copper wire to clean the holes in my jets and carburetors, but with this product, the material is very stiff and easy to handle. This product is very easy to use because of the stiffness of the material and the concave and convex surface to scrape the dirt out of the hole.
If there was another thin one, it would be great.
View detail
![Carburetor Float Level Gauge](https://img.webike-cdn.net/catalogue/13454/tool360_1_TS.jpg)
Is this the PROSpec.
Junk. It's useless. I threw it away immediately.
You can handle this with impunity, can't you? I was a fool to trust you.
View detail
![Float Valve Seat Cleaner](https://img.webike-cdn.net/catalogue/images/54162/KEK-56-10_04_TS.jpg)
A must have in CVcarburetorRestore
The CVKcarburetor, which is commonly used on kawasaki vehicles, has a press-fit Valve seat and cannot be replaced by the SeatSingle Body.
However, it is too stupid to replace the body just for that purpose, but once the tank is rusted, the motorcycle will be damaged by the rust powder and the seat will be damaged.
I used to cry myself to sleep, but when I found out about this product, it changed my world. It actually polishes well and looks like new.
The hang should be of the right size. The large size will not fit in the valve seat and the small size will hit the slant and distort the seat.
View detail
![Carburetor Float Level Gauge](https://img.webike-cdn.net/catalogue/13454/tool360_1_TS.jpg)
there is a tendency to clash
It is difficult to measure the Comma in millimeters precisely because there is a wobble. It may be 0.5mm unit at most.
However, is it really necessary for FloatLevel measurement to be more accurate than that? I guess it depends on the user.
View detail
![Carburetor Jet Driver 4-Types](https://img.webike-cdn.net/catalogue/18491/2525_TS.jpg)
Jet Driver
I used to use a Slotted screwdriver with a little modification, but of course, using a dedicated product makes all the difference, I feel safe and the length is perfect, Large strange, I'm satisfied! I wish I had bought it sooner. View detail
![FCR Carburetor Tool](https://img.webike-cdn.net/catalogue/12250/ym08-0181_TS.jpg)
It is expensive to think of it as a driver, but it is useful in Overhaul
Nut hole in FCR Carburetor Body Carburetoretc.Float chamber I bought it for the maintenance of Carburetor, which can access to Jet from I did If you look for it, you can buy a similar Driver at a cheaper price than Carburetor's Settingetc.You don't have to remove the Carburetor and replace the Jet every time It's convenient because you can work with it on Especially for the 4 cylinder Carburetor, it is a recommendation View detail
![Carburetor Jet Driver 4-Types](https://img.webike-cdn.net/catalogue/18491/2525_TS.jpg)
It's cheap
It works just fine!
this [Contents] Longer Slotted for easy to use throw adjustment of the quadruple carburetor to If the screwdriver is a Quantity:Set would be even better! I have one, so I didn't really need it
Those who buy from scratch buy additional tools as a matter of course they need to buy additional tools, and
View detail
![Carburetor Jet Driver 4-Types](https://img.webike-cdn.net/catalogue/18491/2525_TS.jpg)
I am happy if there is selling Rose.
I bought it for Carburetor setting.
If you do not remove the carburetor you are using the carburetor of Type which impossible to replace Slow Jet due to space and structure problems.
However, working with the attached Minus is now possible with carburetor attached! From now on, it is possible to reduce the time and effort of setting for each season as much as possible!
View detail
![Carburetor Float Level Gauge](https://img.webike-cdn.net/catalogue/images/16993/4852_01_TS.jpg)
Not available
There is too much play in making products, which is inconvenient. There is an error of 1 mm from 0 to 40 mm in display of measurement, and it is impossible to accurately measure the oil level. View detail
![Carburetor Bore Tool](https://img.webike-cdn.net/catalogue/10054/75252_TS.jpg)
Carburetor It may be necessary for cleaning!
I used it for the Slow Jet route.
As the destination is like File? So lubricate oil to prevent scratching
I used it.
In my case the path is packed with things like O - ring fragments?
I was able to take out with this Tool and it was a great change to Large.
Moreover, it is saved that the price is reasonable..
View detail
![Carburetor Jet Driver 4-Types](https://img.webike-cdn.net/catalogue/18491/2525_TS.jpg)
Carburetor decomposition
Carburetor is a precision instrument
I think that it was better if there was a dedicated driver to decompose Carburetor. Because I can not get it back after making a mistake
View detail
![Float Valve Seat Cleaner](https://img.webike-cdn.net/catalogue/images/54162/KEK-56-10_04_TS.jpg)
Individually a little expensive, I want selling Rose
Shared when doing maintenance and restore dozens of people with multiple people in school days
I bought it as a tool of. I think the price has not changed from the past.
I think it is normal to do with a cotton swab, but if it is a cotton swab, it can not be removed,
Cotton Garbage is easy to get out. When the cotton swab is cleaning the cylinder part of Valve seat
I wonder if I can use it.
Because it is a stick of wood, the angle is not right, so it is slightly strict, scrape it like a Taper
Even so it collapses so so it is not good.
In that respect Seat cleaner is sticking an exquisite line. Hardness and accuracy
Good. Large resistance will not be beautiful with a single shot, but if you glide gently, it will be beautiful
Become. There are still some polishing effects, but Seat that got hurt
I can not return it.. Note this point.
(I will glitter it by attaching a fine compound to the original.. )
I think that Material is oil resistant Nylon, but it becomes scratch and stepped wear
It is hard..
Just because it can not be used forever, exchange is necessary if you use it hundreds of times,
At that time I can not buy it at Rose because it hurts. Because it is expensive, I buy it every time in Set
It is tough..
Well, since it is possible to use it without any wear and scratches, if it is individual Youth
It may not be necessary to buy Spare.
View detail