Reviews
In carrying out bore up this time, since it was a required tool, it purchased. I think that they are necessaries, such as future maintenance.
In carrying out bore up this time, since it was a required tool, it purchased.
I think that they are necessaries, such as future maintenance.
View detail
The split pin of phi 1.6 was required and purchased. Since the stock of other sizes also grew in no less than 20 pieces unnecessary although it was the thing which was good at least as for phi 1.6, it carried out here. It is a functional very ordi
The split pin of phi 1.6 was required and purchased.
Since the stock of other sizes also grew in no less than 20 pieces unnecessary although it was the thing which was good at least as for phi 1.6, it carried out here.
It is a functional very ordinary split pin.
View detail
It purchases in order to challenge the tappet adjustment of KSR110. It is as cheap as it says, It says by such a cheap tool. Are the die length, form, and user-friendliness of a gauge as perfect as uncertain (smile) considering the tool used by th
It purchases in order to challenge the tappet adjustment of KSR110.
It is as cheap as it says, It says by such a cheap tool.
Are the die length, form, and user-friendliness of a gauge as perfect as uncertain (smile) considering the tool used by the work which determines the engine engine performance at it?
Although there are also goods with many kinds of thickness of a gauge inexcessively, to put it bluntly, it is useless.
If there is even a kind of required gauge, it is sufficient for Koto.
It is made required and enough, if that meaning is also this product.
Let's take out * five pieces without a complaint!
View detail
In order to remove a flywheel, it will not start, if there is almost no puller. Although it had come out of various manufacturers, and it had become the same price generally, since the screw size was written with the photograph, it purchased here.
In order to remove a flywheel, it will not start, if there is almost no puller.
Although it had come out of various manufacturers, and it had become the same price generally, since the screw size was written with the photograph, it purchased here.
Although it was purchase for exchanging the crank of PW50, honesty and a screw size are not known but the internal thread of a flywheel is measured with vernier caliperses, and from that it was about 27 mm and screwing having been a reverse screw, it judges that it will probably be OK and purchases.
It equipped and was tight.
As it is, adhesion is carrying out, it does not separate, but the shaft of a flywheel (the screw of a puller is likely to be damaged) is oiled, grease is applied to night waiting and the thread part of shaft aggressiveness (?) of a puller, and it challenges again.
It escaped frankly.
Since there were also various screw sizes of a puller and how to remove, it did not understand whether it could use for all the motorcycles, but it was able to use for PW50.
I think that power will enter if it changes and turns to a longer round bar when power is more nearly required since it escapes from a handle.
View detail
It is a vessel for exclusive use for soaking the filter of a twin air in oil. Of course, other containers can be substituted. It is said that osmosis of oil can be efficiently performed by using this product in manufacturer. If it is said espe
It is a vessel for exclusive use for soaking the filter of a twin air in oil.
Of course, other containers can be substituted.
It is said that osmosis of oil can be efficiently performed by using this product in manufacturer.
If it is said especially whether good it is required although it is not necessarily bad .. ? -- since having washed using other containers was troublesome as for me, I am using this product now.
It is just going to say that it is not too bad.
It is a three stars!
View detail
It is a wire indispensable to an off-road run. Although the grip of the off vehicle is pasted up firmly mostly, if it runs to a hard, it may escape or turn. Foundations will carry out wiring too, since the risk will also increase if water pours in
It is a wire indispensable to an off-road run.
Although the grip of the off vehicle is pasted up firmly mostly, if it runs to a hard, it may escape or turn.
Foundations will carry out wiring too, since the risk will also increase if water pours in.
I think that it is convenient also for the wiring of portions other than a grip.
since it is dramatically as cheap as 150 yen -- Mr. Webike's case -- the adjustment for mailing cost no charge -- convenience that's right.
View detail
Since an adhesive bond will separate and a grip will turn if weight is applied to a handle in a trekking etc., or a handle is pulled although front up is carried out even if it fixes a grip with an adhesive bond, Since a grip is fixed more firmly, it
Since an adhesive bond will separate and a grip will turn if weight is applied to a handle in a trekking etc., or a handle is pulled although front up is carried out even if it fixes a grip with an adhesive bond,
Since a grip is fixed more firmly, it uses together with an adhesive bond and is binding the grip tight with the wire here.
You fully have to bind tight to demonstrate an effect firmly.
if it twists pulling [ it not only merely twisting, but / when twisting and binding a wire tight as a hang ] -- GITCHIRI tightness measure.
However, requiring special attention, since a wire will eat away and a grip will go out, if it fastens too much since a degree is also required.
About 2~3-set grade construction can be carried out in one piece.
Although he had gone out for the trekking after wire wearing, when it ran too on the 1st, the grip had turned like the semicircle.
It seems that there is an appropriate effect since having turned with GURITSU has been improved if weight was still applied to the handle when he had no wire.
How about winding [ the direction which rides on an off-road motorcycle ] a wire around the occasion which exchanges grips, since it is not an expensive thing?
View detail
It was used for the oil change of a front fork. Since the lid is also attached, it is dramatically good. However, since the raw material of a cylinder is a raw material like a tapper of a plastic and the container for food preservation, if it is n
It was used for the oil change of a front fork.
Since the lid is also attached, it is dramatically good.
However, since the raw material of a cylinder is a raw material like a tapper of a plastic and the container for food preservation, if it is neglected for a long time at a hot place, it is anxious whether it changes and memory becomes as measurement.
View detail
It used for exchange of fork oil. The lid of the rubber attaches goods or they are very good at care. however, since the last carries out oil level adjustment if fork oil exchange is only carried out, fine memory is unnecessary -- it is . Or [
It used for exchange of fork oil.
The lid of the rubber attaches goods or they are very good at care.
however, since the last carries out oil level adjustment if fork oil exchange is only carried out, fine memory is unnecessary -- it is .
Or [ that a plastic bottle may be sufficient since a certain amount of quantity should just be known if it uses only for fork oil exchange when it thinks ].
When it thinks so, isn't it somewhat high shopping?
View detail
It purchased by the adjust wrench set and a set for the tappet adjustment of YBR125 ('06). If die length was insufficient, it was worried for a while, but in my case, it was required sufficient die length. In the case of a motorcycle with bad serv
It purchased by the adjust wrench set and a set for the tappet adjustment of YBR125 ('06).
If die length was insufficient, it was worried for a while, but in my case, it was required sufficient die length.
In the case of a motorcycle with bad serviceability, a little longer thing may tend to work.
Since turn is only tappet adjustment and plug gap adjustment, after using, it washes by engine oil each time, wipes off lightly, and is IN at an attached case.
A few is a spell called the kana which lasts long ^^;
View detail
It is oil leakage discovery from a mission cover immediately after putting in an oil additive. it is also wasteful to change the oil completely -- was thought, and it purchased so that the oil discharged for gasket exchange could be reused. It was
It is oil leakage discovery from a mission cover immediately after putting in an oil additive.
it is also wasteful to change the oil completely -- was thought, and it purchased so that the oil discharged for gasket exchange could be reused.
It was satisfactory user-friendliness.
Since it is thick, a higher vehicle may be unable to use it for a low vehicle type.
View detail
Simultaneous purchase was carried out in order to use a vacuum gauge. When a gas tank is removed, it is used as a sub tank. The place which is possible by the fuel cock being attached and supply of a gasoline being arbitrary is wonderful. Alth
Simultaneous purchase was carried out in order to use a vacuum gauge.
When a gas tank is removed, it is used as a sub tank.
The place which is possible by the fuel cock being attached and supply of a gasoline being arbitrary is wonderful.
Although the fuel hose and size of the joint of a fuel cock of vehicles did not suit, it did not leak by an attached hose clip and fixation was also completed.
Since I think that it is somewhat expensive since it is exclusive elegance, but it becomes necessaries at the time of a carburetor or engine conditioning, work will become a smooth if it has one.
View detail
Although it had ridden on SR400, the goods here were used by tappet adjustment. Although 0.10 mm and an exhaust side perform tappet adjustment of SR at 0.15 mm in an inspired air flow path, since there is a gauge of the size exactly, it is very conven
Although it had ridden on SR400, the goods here were used by tappet adjustment.
Although 0.10 mm and an exhaust side perform tappet adjustment of SR at 0.15 mm in an inspired air flow path, since there is a gauge of the size exactly, it is very convenient! Since a price is also cheap, it is bought, and there is no loss.
View detail
It is convenient that the lid is attached. Since oil level adjustment of the adjustment of fork oil is carried out eventually, even when memory is suitable, it is satisfactory.
It is convenient that the lid is attached.
Since oil level adjustment of the adjustment of fork oil is carried out eventually, even when memory is suitable, it is satisfactory.
View detail
It was used for tappet adjustment. Since it is consumable goods, the low price of this price thinks that it is good.
It was used for tappet adjustment.
Since it is consumable goods, the low price of this price thinks that it is good.
View detail
It is used for air gap adjustment of a plug gap and a crankshaft sensor. Although other goods have not been used, it is easier-to-use than imagination -- only a required plate can be easily taken out by a screw type. A thickness display is also la
It is used for air gap adjustment of a plug gap and a crankshaft sensor.
Although other goods have not been used, it is easier-to-use than imagination -- only a required plate can be easily taken out by a screw type.
A thickness display is also large, is intelligible and thinks a quality level appropriate also in price.
When looking for the goods same incidentally in the neighboring home center, it was a price of 1.5 times or more.
View detail
It purchased for front fork oil exchange. It is since [ university's experiment ] that touches a graduated cylinder. It is an about 30-cm plastic with the lid of a rubber. However, since it adjusts by a level gauge after all, I feel that it wa
It purchased for front fork oil exchange.
It is since [ university's experiment ] that touches a graduated cylinder.
It is an about 30-cm plastic with the lid of a rubber.
However, since it adjusts by a level gauge after all, I feel that it was unnecessary for the thing so far.
View detail
The die length of the feature of this schickness gauge is a long time moderately. It can work like a photograph also at the time of adjustment of valve clearance, being able to have a margin. Although the shorter gauge was used before, troubles we
The die length of the feature of this schickness gauge is a long time moderately.
It can work like a photograph also at the time of adjustment of valve clearance, being able to have a margin.
Although the shorter gauge was used before, troubles were suffered without the ability to perform flexible bending like a photograph.
I think that they are goods excellent in cost performance.
View detail
It was used for the tappet adjustment of ST250. Though troubles were suffered since the number of bulbs was two, it was able to do by itself. Since it was quite thin, reinforcement was anxious, but it is satisfactory at all. Since it is a prec
It was used for the tappet adjustment of ST250.
Though troubles were suffered since the number of bulbs was two, it was able to do by itself.
Since it was quite thin, reinforcement was anxious, but it is satisfactory at all.
Since it is a precise tool, when using it several times, the way exchanged for the new article may say.
A price is also cheap.
View detail
It was used for the first front fork OH work. Although there were some goods of about the same price, it is charmed with a lid and purchases. Since it was stabilized since the step was solid, and the lid stuck and mixing of dust etc. was prevented
It was used for the first front fork OH work.
Although there were some goods of about the same price, it is charmed with a lid and purchases.
Since it was stabilized since the step was solid, and the lid stuck and mixing of dust etc. was prevented the inside of use, and after use, it was convenient.
Since the overall length is long so so and it surely remains in a bottom as 1 ml, I think eventually that oil level adjustment is required.
View detail