Reviews
Slightly difficult to install, but functions well
Helmet holder for retrofit type.
Demerit is that it doesn't come with a key from the beginning like Kawasaki does these days...
It is 100 times better than hooking up to a Tandem seat.
Functionality is adequate.
There is a slight problem with the installation, because the Bolt that holds the Plate is close to the body of the car,
In a normal hexagonal Wrench, Quantity:Only 1 pc out of 2 pcs could be tightened.
I think it can be tightened by Offset wrench etc. because there was a gap of about 20mm when I temporarily tightened it by hand.
Also of note, this Helmet holder uses the Bolt hole on the back of the Tandem Footpeg.
Since these are probably bolt holes for installation of OEM SoftSide case brackets, it is necessary to confirm whether they can be used together or not.
View detail
![[K・TOUR] Helmet Holder](https://img.webike-cdn.net/catalogue/images/97787/80x564x28030xa0_TS.jpg)
I think I got the wrong model number….
I don't know if I got the year wrong, but I couldn't fix it with 2 points, but with one bolt, so I'm a little worried. I am satisfied with it. View detail
Helmet lock
I had been thinking about installing the Helmet Lock Holder, but finally decided to go with METALGEAR, View detail
Can also be installed on the GSX-S1000GX.
[How is it used?
In the photo, I used a helmet, but I was concerned about the load on the chinstrap, so I installed a wire lock and used it to lock the seat bag.
Was the one you received as per Image?
It was just as Image.
Was the installation difficult?
It was easy to install by simply removing the Bracket from the Tandem Footpeg.
The Bracket is quite heavy, so recommends that you remove it while holding your hand on it.
How was your experience with it?
I am satisfied because I don't have to take off the tandem seat any more because I don't have a helmet holder.
[Included Parts:were they on?
Key Quantity:2pcs and Instruction Manual, 2 KIJIMASticker
[Was there anything that disappointed you?
I was expecting to be able to convert it to one-key, but the keyway was the opposite type from the vehicle. If you want to convert to one-key, it is difficult to purchase on Net.
[Availability and clarity of the Instruction Manual
Even the Torque value of the BracketBolt of the Tandem Footpeg was kindly listed.
[Opinions and requests to Manufacturer
The GSX-S1000GT and RearSub-frame seem to be the same and can be installed. We would appreciate it if you could add it to the list of compatible models.
View detail
The construction is very good, but when you actually use it, it is very difficult to use.
The make is very good and looks OEM 。 I put it on my MOTO GUZZI which does not have a helmet lock, but it is attached without any discomfort. 。 However, in actual use, the helmets touch the exhaust system because of the low position of the helmets. View detail
I am very satisfied
Installation of the product is very easy. Also, the delivery of the product is very fast, and the product description page and configuration are the same. View detail
Direction of opening and ease of use as desired
I wanted a helmet holder that could be mounted with the open/close hook facing vertically, and that could be opened on the top side.
After installation, the upper hook opens from an oblique position so that the helmet is stable and secure without fear of falling off.
The design blends in with the car body and is unobtrusive and easy to install.
I'm glad I installed it.
Large was active in Touring immediately.
View detail
Shipping is good.
It is only now possible to attach an external DialWire lock to the Handlebar.
I think what you want to do is reasonable.
However, we still would like to see some improvements due to the use of existing locks.
1.Dial is Smaller
I don't want to touch it in the winter or anything.
2.Wire is too long.
Handlebar position could be half as short as it is now.
3.Lock position
Not the other way around, as they tend to pop up on the Grip side and interfere with each other.
I dare to put it on the other way around.
It would be nice if this area could be improved, but it is regrettable.
View detail
Useful if you have it ^^.
[How is it used?
When you stop at Convenience or some other place where you stop for a bit.
Was the one you received as per Image?
Large Image Street
How was your experience with it?
It did not go into the CYGNUS Hell Lock pin as is.
[Points to note]
The pin holes are unexpectedly small, so some modifications may be necessary depending on the vehicle.
How did it compare to other products?
No comparison
Other items that would be helpful
As a side note, the included Carabiner is too small.
The 100 yen shop items of today are of higher quality.
View detail
Cannot be installed with Carrier
Ease of use of Helmet lock is normal
Installation was easy with tools.
Note that if a KIJIMA Rear Carrier is attached, it will overlap the Pipe and will not be usable.
It's about making sure you use other locks.
View detail
Installation of helmet holder on XSR125
We install most of Motorcycle's helmet holders on each vehicle we deliver.
As usual, it is useful for Helmet lock when parking the bike.
It is a vehicle specific product, but I had to shave it down a little to install it because it hits the side cowl a little.
View detail
![[K・TOUR] Helmet Holder](https://img.webike-cdn.net/catalogue/images/108481/80-564-90250_1_TS.jpg)
Place Helmet on Top Bridge and lock it.
The standard helmet holder of ZX14R was placed on the Left Tandem Footpeg, but when the exhaust system was replaced, the Tandem Footpeg was removed and the helmet came in contact with the silencer. The silencer is no longer used since it is placed on the Top Bridge because the rubber may melt when the silencer is hot.
I had been leaving it unlocked, but since I bought a new helmet, I was concerned about theft and decided to purchase a retrofit helmet holder.
It was attached to the Multi Bar with Smartphone Holder so that the Shield could be opened for easy key operation.
It lacks a SMART appearance, but it has achieved its purpose for now, so I will use it for the time being.
I might remove it if I can't stand it anymore (laughs).
View detail
To relieve the anxiety of a short break.
I bought this product because the CBR1000RR SP sc77 does not have a Helmet holder in OEM and there is no Screw hole to install a Type product that mounts on the Frame.
I used to hook it up to Mirror when I took a break at a touring destination, but it was half the fun with the fear of theft.
After installing this one, I was able to leave the vehicle body with some degree of peace of mind, so I think it is actually quite cost-effective as a cost-effective solution.
Installation is not particularly difficult as long as the size of the car body is carefully checked.
If I had one request, I would have liked the key to be 4-digit instead of 3-digit. I thought that if you leave for a long time for meals, etc., it might try all patterns and be unlocked.
View detail
Very good product
I like it because it is Design cleaner than other companies' products.
Installation was easy and the feel is very good.
Spare key is also included.
The bolt is also a stainless steel bolt.
View detail
Fits: DUCATI MONSTER1100/S, DUCATI MONSTER796, DUCATI MONSTER696, DUCATI MONSTER796, DUCATI MONSTER696
Might be easier to use.
It can be said that it is easy to hook because of its large opening, but it is difficult to remove it without using both hands.
It happens to be the place where the Battery Charging Cable is out, so you should think carefully before attaching it.
View detail
Fits: Others , HONDA MONKEY125ThailandMODEL, HONDA MONKEY125, HONDA PCX160, SUZUKI GN125-2F, YAMAHA YB125SP, YAMAHA XTZ125, KAWASAKI KLX125, KAWASAKI D-TRACKER125, KAWASAKI Z125PRO, KAWASAKI KSR110PRO, KAWASAKI KSR110, YAMAHA XT250SEROW, HONDA CRF250L, HONDA CRF250RALLY, HONDA Dunk, HONDA MAGNA50, HONDA XR100 Motard, HONDA XR50 Motard, HONDA APE100 TypeD
Nice little addition to my Monkey 125
I live in an urban area and wanted to keep my helmet locked with my bike although theft is not too common here. The stock helmet lock is located at an awkward spot that's too low and inconvenient for me - I had to try out this one. Installation is easy, product works as promised. View detail
Fits: Others , YAMAHA BWS 50, YAMAHA BWS125, YAMAHA MAJESTYS, HONDA ZOOMERX, HONDA PCX125, HONDA PCX125 E:HEV, HONDA PCX125 Hybrid, HONDA PCX150, HONDA PCX160, HONDA CROSSCUB110, HONDA glom, HONDA MONKEY125, HONDA CB125R, HONDA CBR125R, HONDA CB250R, KAWASAKI Z125-PRO, HONDA DAX125, HONDA CT125CT110 HUNTER CUB, HONDA CL250
For CL250
Side Back on CL250
Because it is installed
Master Cylinder in Kochira
Type's installation on the
Helmet holder.
View detail
Fits: BMW R1200GS, BMW R1200GSAdventure, BMW R1250GS, BMW R1250GSAdventure
No need to worry about food while touring.
I used to hang my helmet on Mirror when I took a break during touring. I was worried that it might be stolen or fall off, but now I feel safe! However, I am worried about rust because the material is steel. It is easy to install and just fits. View detail
Fits: HONDA PCX125, HONDA PCX125 Hybrid, HONDA PCX150, HONDA PCX160, HONDA CB125R, HONDA CBR125R, HONDA CB250R, KAWASAKI Z125-PRO, HONDA PCX125 E:HEV, Others , YAMAHA BWS 50, YAMAHA BWS125, YAMAHA MAJESTYS, HONDA ZOOMERX, HONDA MONKEY125, HONDA glom, HONDA CROSSCUB110, HONDA DAX125, HONDA CT125CT110 HUNTER CUB, HONDA CL250
It does not mount well.
The genuine brake lever and the product are not fastened well, resulting in a part left on the handlebar. To mount the helmet, the direction was reversed. View detail
It would be more convenient to have
There is one on the Body, but I bought it because it is inconvenient to use it without removing the Seat, and also because it is essential when I tandem the body.
I am satisfied, including the price.
View detail