Reviews
Sharp Reflector
The ReflectorSticker in the Included Parts:of the AELLAFender Eliminator Kit was not good, so I was looking up Reflector on the website and found this product.
I liked the casual design under the License Plate.
View detail
ACTIVE Reflector
Slim type Reflector.
It's a shame that the Bracket was twisted when installed and was not slightly straight.
View detail
Installed in Motorcycle yard.
I installed it in the parking lot for my motorcycle in my small yard on the way home from touring. It is very sturdy so even if I ride up on it with my motorcycle it doesn't scare me! It also contributes to safety as it reflects the light and shines well! The double-sided tape on the back has good adhesive strength and does not come off! View detail
Durable!
I put one on the back of my car and the rest at the entrance to Garage. I scraped it on the ground once when I fell over, but it was strong and only got a few scratches! It's a great job and it's a Recommendation! View detail
A bit expensive but high quality! Be safe!
I have experienced an accident with a child, so I put this product on my Rear Bag for safety first!
I feel that the number of times I have been forced to close the distance between cars has decreased since I completed the application! Safety first! I will be an active Rider for life! This is a recommendation!
View detail
If you're willing to rip it off, be careful.
Items convenient for products that also have a protector, so even if they are attached to protect scratches, they look like they are attached to improve visibility.
However, when peeled off, it left a mark and was a type of adhesive that was difficult to remove even with Seal peel, so I recommend using another double-sided tapeetc. if you are thinking of peeling it off.
View detail
Thick enough! Reflects well too!
We were looking for a reflective Sticker to improve safety. At first, we were looking for a reflective Sticker sold at a hundred-yen store.
I was dissatisfied with the adhesive strength and stuck this product on it.
I am satisfied with the results! When degreased properly, it does not peel off even if it rains, and it reflects the light of following cars perfectly.
It contributes to safety improvement! It is easy to apply, so it is a recommendation for everyone!
View detail
A little cheaper would be nice
Short fender was installed along with the conversion to side number.
It is easy to attach with double-sided tape.
It would be helpful if it were cheaper since it is just a Reflector.
View detail
Exquisite Items that add charm
I put it on because I felt it would add to the cuteness. View detail
Stylish & Compact despite Japanese Vehicle Inspection Correspondence
I was attracted by the compactness and slimness of this Japanese Vehicle Inspection Correspondence. I think it will look stylish in combination with the Fender Eliminator Kit. View detail
My car ZX-6R is also like Motorcycle for International Model.
What was the deciding factor in your purchase?
Side reflectors are standard equipment on motorcycles overseas, and I believe that side reflectors increase the visibility of motorcycles and also help prevent accidents if drivers around you notice them by timing their vehicles quickly. I think it will lead to the prevention of accidents. I installed side reflectors on my ZX-6R as well, just like those for International Model motorcycles.
[How was the product?
EMark Income Reflector, OD is 40Φ, M6 Bolt Fixed Nut with Washer.:1pc., so Quantity:Pair (for Left and Right) Two must be purchased if they are to be matched.
When installing on the ZX-6R, the ReflectorSingle Body hits the Front Fender, so we used KITACO's aluminum spacer collar 5mm and a polycarbonate washer. However, the Bolt's bite is reduced by the amount of spacer, so we installed the Bolt firmly to prevent it from coming off. We are now thinking of measures to be taken in the future.
[Others]
Side reflectors will also be mandatory for New Model vehicles to be certified by the government after September 2023. This revision of the safety standard applies to New Model vehicles that will be certified by the Japanese government in September 2023 or later, and side reflectors are not required to be installed on motorcycles manufactured before that date. However, these parts will increase visibility, although not absolutely, and help prevent accidents by making drivers and pedestrians around you aware of your vehicle by timing it earlier. You may want to consider installing them, especially if you drive a lot at night.
View detail
ナンバープレートなどを夜間に反射する場所に取り付けるために使用されます。そして、それはすべての車に適していると思います。そして簡単な取り付け手を置いてください。可愛い小物です。そしてパッケージも綺麗で気に入りました View detail
Required to make Fender Eliminator
I purchased this because I needed a reflector when converting to Fender Eliminator.
Installation is co-tightened with the License Plate.
Three shapes (Square, Trapezoid, Slim)
Two colors (Black, Silver)
so you can choose the one that fits your Motorcycle.
Also, note that SmallEngine Displacement Volume (125cc or less) reflector kits have different dimensions between the holes, so be careful when buying them.
View detail
Easy installation
Just tighten it together with the License Plate.
Easy to install, very nice!
View detail
Satisfied with the new look and feel
I was looking for a round mirror that could be attached to the bolt of the Right Side Opposite Thread Screw without an adapter, but I couldn't find anything like it, so I decided to purchase this product's Mirror Bracket and Fixing Bolt in quantity.:Pair (for Left and Right) Purchased at Rose.
Quantity:This is because there was no Round Type Opposite Thread ScrewSpec. available for sale as a Set (there is a Normal Thread Screw with security parts). (Normal Thread Screws with security parts are available)
I have not driven the car after installation, but I don't think I will be bothered by the slight shaking that occurs when the engine is revved up.
The Mirror part can be moved to some extent (30 degrees in all directions according to the manufacturer) even after it is fixed, making it convenient for fine adjustment.
Although a smaller Mirror would have been ideal, the Mirror's area meets safety standards.
It is a little harder to see directly behind the Mirror than the previous horizontal Mirror, but this may be adjustable by extending the Mirror section more to the tip of the Bracket. However, once fixed in place with the imonesi, that part of the Bracket can be " and marks, so it is better not to move around too much.
I used a spring washer to prevent loosening during installation.
At first, I used the ring on the base, but it was too loose, so I decided to use only the spring washer.
View detail
Reflector
I changed from a round reflector to a Slim reflector. View detail
To MONKEY125Rear.
The KITACO product is well made, and the KITACO mark is subtly placed in the middle of the reflector, which is nice. View detail
With the conversion to rear fender-less... Part 2
At first, when we finished the inexpensive Rear fender-less conversion with Home center's Bracket, we used OEM reflector, but we replaced it with this one because it seemed to be able to refresh.
[AEBS] I had already replaced the LED Blinker Lamp Set when I posted my impression of it, but here it is again as an impression of this product.
View detail
no problem
K-FACTORY's Fender Eliminator Kit requires a separate reflector, but the company's product was expensive, so we chose this relatively inexpensive and stylish product. We were able to install it without any problems. View detail
unexpected
I tried to buy an integrated type that does not require a reflector bracket to reduce the burden of the Fender Eliminator, but it was 3mm thick! I found out that this one is heavier than the one I have now with the License Frame and Reflector Bracket. I don't know if it is necessary for License Frame to be this strong, but the thickness should be written in the description. View detail