Reviews
Stainless black
The silver stainless steel screws on the bends stand out oddly, so we replaced them with black stainless steel screws.
The colors match and it looks better now that it looks better.
View detail
Fits: HONDA MONKEY
If the price is a little lower, it's a good choice
I used the same product Gold as this one
You can remove and put it on and off every time you do the setting
Because I applied a little force when I tightened it, I ruined a Screwball mountain
I'm going to re-purchase the blue one this time
Since DrivenSprocket spacer is also installed, this time without washer I'll install it
(I'm changing the Bolt, which is a little long, but when I put in Washer, it doesn't take until the end to get the Nut
View detail
Fits: HONDA MONKEY
Just the right amount of tightness!
We did a RearDrivenSprocket exchange for MONKEY
I had to remove and install it about 3 times because it was a little bit displaced
One of the threads was ruined because I tightened it too much
Material:It's Aluminum, so it's better to tighten it appropriately
I'm currently a Gold Sprocket and will buy Blue again
View detail
O-ring is ...
Mounting on YZ250F and Husq 's SM450R.
Although Husk was hard but could be installed easily, YZ person was muddy in Small Small in the hole of Air Screw or O - ring did not enter at all, painted oil and repeatedly TRY I did not enter after all but I removed the carburetor and cleaned it up. Separately this product is not bad But when using it for Motocrosser, let's do it after dropping mud dirt firmly
View detail
Fits: HONDA MONKEY [MONKEY]., HONDA MONKEY [MONKEY].
One point ♪
I bought it to match the color of Chain and Sprocket.
I like it myself ♪
The object itself is lighter than the OEM.
I would like to see how long we will be durable.
View detail
Not possible
Quantity for YZ 250 F and Husq 's SM 450 R : 2pc purchase.
Since Air Screw adjusts frequently according to the temperature, it is troublesome to turn Screw with a special driver each time, so I bought it.
YZ can be adjusted to Smooth because there is no Engine Starter Motor, but Husk has Engine Starter Motor under the carburetor so how do you think it is slightly subtle. I have not installed it yet.
A bad point :
The price is expensive. I think that it does not need such a thing personally though a figure or fine workmans is attached. I think that it would be enough if the mark or the line which Screw can turn by hand and become a standard to some extent is scraped. From other Manufacturer I would like you to issue a MODEL that has reduced more in cost.
Well, since it is a thing of hobby, it is Large thing in terms of added value (Lol)
View detail
Although the Bolt has already disappeared with the photograph, it can let wiring pass by such touch. -- Although it is perfect if only this product was found however it might search, but there is one long 5 more mm ... -- it and a price -- just
Although the Bolt has already disappeared with the photograph, it can let wiring pass by such touch.
-- Although it is perfect if only this product was found however it might search, but there is one long 5 more mm ...
-- it and a price -- just for a moment ... although it is unavoidable since it is goods which seem to be technical very difficult well ...
View detail
I think that it corresponds to the general thing of the Cables of a Motorcycle since it is elastic. As for a certain grade, since it becomes easy to hook it at the end of a metalworker implement, etc. although there is intensity, the way which took
I think that it corresponds to the general thing of the Cables of a Motorcycle since it is elastic.
As for a certain grade, since it becomes easy to hook it at the end of a metalworker implement, etc. although there is intensity, the way which took care for a while may say it.
Since the both ends of the Tube at the time of equipping after
are frayed easily simply, it is necessary to wind exactly and to stop them on a heat-resistant Tape etc.
View detail
When exchanging for the LED mirror blinker of JP moto mart, it purchased in order to make wiring processing easy to carry out. Since the screw hole of the upper cowl stay which is fixing the mirror of CBR1000RR is a non-penetrating formula, it needs t
When exchanging for the LED mirror blinker of JP moto mart, it purchased in order to make wiring processing easy to carry out.
Since the screw hole of the upper cowl stay which is fixing the mirror of CBR1000RR is a non-penetrating formula, it needs the drilling process by the side of a car body in advance.
Furthermore, since this bolt is also too long, it becomes cutting off about 15 mm very well exactly.
Since the screw of M6 was only made hollow, it cannot let not much thick wiring pass.
slightly a hard still although wiring of a mirror blinker which I bought is rather the thinner one -- it feels.
Let's be as hollow truly, and since the screw itself will twist and bend if the torque bound not much tight is too strong, take care.
Although slightly high mind of 1000 yen is also carried out by two, I think that considering the time and effort and preparedness which carry out a drilling process to an upper cowl it is cheap.
View detail
Although the one way valve of the long hose was attached until now, since the price was also handy, it equipped with this product. After wearing does not have signs that it separates, either and is attached firmly. However, when it failed to get o
Although the one way valve of the long hose was attached until now, since the price was also handy, it equipped with this product.
After wearing does not have signs that it separates, either and is attached firmly.
However, when it failed to get off the ground, it was unexpected that a gasoline flowed out.
View detail