Reviews
Fits: KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA
A position that will never get old.
The bike had a wide handlebar from the time of purchase, but when I thought about long distance riding, the riding posture, etc., became very difficult, so I decided to go with the OEM handlebar.
Of course, Cableetc. is also OEM.
I have ridden on vehicles with various shapes of handlebar, such as Separate handle, Wide, TRACKER, etc,
OEM Handlebar of Large Body is Pipe Handlebar, isn't it?
Pipe Handlebar
Pipe Handlebar is a handlebar made by bending a single piece of pipe, and is used in a wide range of models from naked motorcycle to American motorcycle, and is the most standard handlebar. 。 There are a variety of shapes and sizes, from flat-shaped models for sports driving to models with high handles for Americans.
Flat shaped Handlebar is Continental handle The high handlebar used for American and other products is Handlebar Up Type It is called
Why is the OEM Pipe Handlebar?
Pipe Handlebar Characteristics
。
Suitable for long-distance touring, as it does not tire easily even after long hours of driving. 。 In addition, the handlebar is easy to turn off, making it easy to turn around at low speeds and maneuver when dismounting.
=It's a Handlebar that is less tiring on Motorcycle. And Large Resistance is easier to handle.
And the material used for OEM handlebars, including ESTRELLA, is Steel.
SteelHandlebar is ...
Characterized by low strength and heavy weight.
→It looks like Demerit, but it's not Demerit.
Since the strength →Cost surface ...
The weight of the handlebar is a good measure to prevent vibration. If there is a lot of vibration, it means that the handlebar is heavier.
We considered those advantages and made it OEM.
What I also liked was the Handlebar width. It's 72.5 cm in actual size and 8 cm high, which fits my physique (laughs).
Replacement procedure.
Please remove *Mirror.
(1) Level the car body 。
↓
Remove the clutch lever and cable.
↓
Remove ?Brake lever and Cable.
↓
(4) Remove the Axel and Accelerator Wire.
↓
(5) Remove Handlebar Post 。
↓
(6) Remove the existing Handlebar.
↓
(7) Attach a new Handlebar and tighten the Handlebar Post.
↓
? ?→? undo in this order.
■ Comments
I bought a modified car and drove it as is, so I didn't know about the OEM's position. But it's not the kind of forward lean that hurts my back, it's a normal NAKED type position.
The handlebar width has been reduced, and the volume of the tank is more prominent, which I like.
View detail
Fits: KAWASAKI ELIMINATOR, KAWASAKI ELIMINATOR, KAWASAKI ELIMINATOR 250V, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ZEPHYR X, KAWASAKI ZEPHYR X, KAWASAKI ZEPHYR X, KAWASAKI ZEPHYR X
I think it is an elaborately designed OEMMirror.
I would love to have a stylish Mirror for ESTRELLA, but I have returned my SR400 to OEM Mirror, and I have reaffirmed the visibility and safety of OEM Mirror, so I have decided to buy another OEM Mirror for ESTRELLA as well.
ESTRELLA's OEMMirror, Quantity:Pair (for Left and Right) to
[Motorcycle Back Mirror]
... can check the back of the Motorcycle. Back Mirror is a safe way to travel. Security Parts 。
For motorcycles with a maximum speed of 50 km/h or more, the Quantity:Pair (for Left and Right) s Back Mirror is not installed, it is subject to violation of the Road Traffic Law.
Mirror is a must for Motorcycle.
Back Mirror is indispensable to check the backward direction while driving a motorcycle.
Considering the current traffic situation, there are many cases where it is dangerous not to check the rear of the vehicle, and it is a very important security component.
And if you don't wear Mirror, you will be punished with Gold as a violation.
Mirror safety standards
...Motorcycle's mirror surface area is more than 69 square centimeters 。 If the Mirror is circular, the diameter must be between 94mm and 150mm to comply with the safety standard.
Mirror mirror surface area, regardless of shape, must be at least 69?! 。 For example, 70mm×100mm is OK, but 70mm×90mm has an area of 63?, which is ? in terms of safety standards. 。 For a square, 83mm×83mm is ? at 68.89?.
(Since it is a 250, it is not subject to inspection, but in the rare case that it is stopped by the police on a public road, it will be subject to improper maintenance as a vehicle with unauthorized modifications. 。 He said that it would be policed as an illegal modification, Gold, a penalty of up to six months in prison or 300,000 yen. I'm not sure if it's a good idea. →It's pretty tough...there's been a lot of enforcement lately, so you have to be careful.
And Mirror is only one ?.
According to the Ministry of Land, Infrastructure, Transport and Tourism, "Motorcycles exceeding 50 km/h are Quantity:Pair (for Left and Right) Both Sides must have 1 pc. each of the posterior mirrors."
Quantity:Pair (for Left and Right) I was certainly surprised at how much easier it was to see the "A" on the "B".
[Visibility] Safety Standards We want to focus on such things as the OEM.
【good point】
◎Rounded rectangular shape Mirror.
Design is good when considered as OEM.
Visibility is of course there. The blind spots seem to have been reduced.
I like the ◎Plating is beautiful and suits the car body.
[Bad point]
The design is so delicate that it can be loosened by vibration (laughs).
▲Steel, so worry about rust. Please wipe it with a blister.
The concept of ESTRELLA Motorcycle is Retro, and I have the impression that it is a well-designed Mirror even if we consider it as an OEM.
It is easy to see, and this shape can be used with the Quantity:Pair (for Left and Right) I think Parenthesis is a good idea even if you put it on.
View detail
Fits: KAWASAKI ESTRELLA-RS CUSTOM, KAWASAKI ESTRELLA-RS CUSTOM, KAWASAKI ESTRELLA-RS, KAWASAKI ESTRELLA-RS, KAWASAKI ESTRELLA-RS, KAWASAKI ESTRELLA CUSTOM, KAWASAKI ESTRELLA CUSTOM, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA
Prepare for the unexpected.
When I bought the vehicle used, it had been changed to an external Switch and did not have a Kill Switch.
At the time of purchase, I did not think the kill switch was that important, but when I understood the meaning of the switch, I thought it would be a good idea to put it on and decided to install an OEM kill switch.
What is Kill switch?
‥ A Switch that stops the required Engine when it is directly connected Wiring. →The one that forces Engine to stop.
And it seems that the Kill switch was originally equipped for Race vehicles.
It used to be a piece of equipment on Race vehicles.
The old 2-stoke racing machine etc. did not have a battery, but only the power generation function of the Engine, and since the Engine is started by “pushing”, it is not equipped with a Cell starter, and if it is for Race cars, it is not equipped with an Ignition key. The engine is not equipped with a cell starter because it has to be pushed & rdquo; to start the engine. This means that a switch”is needed to stop the engine at the end of the run, and that is the Kill switch.
In the case of racing machines, an important reason why a kill switch is necessary is that in the event of a fall or accident, the engine may not stop and the tires may continue to rotate, which would interfere with rider rescue and machine removal operations, as well as pose a risk of igniting leaked gasoline. There is also the danger of igniting leaked Gasoline. 。
In such an emergency, we needed a kill switch that could instantly stop the engine.
This is also the case for four-wheeled races, which are required to be equipped with a kill switch on the outside of the vehicle body so that the course marshal can stop the engine from the outside even if the driver is injured or otherwise unable to stop the engine.
It seems like a device to be used in an emergency state, but as a general Rider.
In what situations would it be used?
[Occasions of use.
→Motorcycle when it falls over.
When→Throttle system failure occurs.
and used in emergencies such as
As for situations where it can be used outside of an emergency situation,
Example:For example, at a toll gate on a toll road, if you stop at a toll gate and immediately stop the engine with the Kill switch while keeping the GEAR in first gear, you can remove both hands from the handlebar without emitting Neutral, making it easier to take out the wallet, etc.
→ To re-start, simply hold Clutch and press the Cell button to start the engine (this method is also convenient for long traffic light waits, etc., as it eliminates the need to exit Neutral).
2.Kill switch installation
It is recommended to spray the inside of the coupler of the Kill switch to be replaced with a contact resister for protection.
Pass the wiring of the Kill switch through the designated position.
How do I install Kill switch?
Remove (1) Seat and Side cover.
↓
(2) Remove the Minus terminal from the battery. 。
↓
(3) Plug in the Coupler of the Kill switch.
↓
(4) Tie Wrapetc. so that Wiring does not get tangled and SwitchBody comes to the RightHandlebar.
↓
(5) Tighten the screws at the bottom of the SwitchBody.
↓
(6) Connect the Battery with the Minus terminal disconnected, put back the Seat and Side cover, and finish.
Check the operation.
Kill switch note...
Note that if you forget to turn off the kill switch and turn off the ignition key when parking the car (i.e., leave the key on), the battery will run up.
If used correctly, it is a device that can avoid the worst in the event of an emergency, so it is safer to have it on.
View detail
Fits: KAWASAKI VERSYS 1000, KAWASAKI VERSYS 1000, KAWASAKI VERSYS 1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z750, KAWASAKI Z750, KAWASAKI Z750, KAWASAKI Z750, KAWASAKI Z800
Perfect fit
A perfect fit for the Kawasaki Z1000 (ZRT00A) built in 2003.
The conversion was completed within 10 minutes without any complications. ---------------------------------------------------------- Perfect fit for the Kawasaki Z1000 (ZRT00A) from 2003. The conversion was completed within 10 minutes without any complications. Powered by Google Translator
View detail
Fits: KAWASAKI KLR650, KAWASAKI KLR650, KAWASAKI KLR250, KAWASAKI KLR250, KAWASAKI KL250R
Genuine Kawasaki LH Grip for KL250R 1990
This is the left side grip which was a neccessary part for a bike. I have started rebuilding this Kawasaki KL250R which requires a lot of genuine Kawasaki parts. I could buy random after market parts but sometimes, you just have to get the genuine ones. I decided on this OEM one as it is with fitting the era of the age of bike I am doing. The part number was not hard to find and added to my order with a few other parts as well as the right hand side grip. Using EMS all my order was shipped and delivered in 5 days solid. The package was well padded and no damage to any of the parts I ordered. This left hand grip is beautiful. I know it's just a grip but the look on it's own is great and of course the quality is erfect as always from Kawasaki. The OEM was definitely the best choice for this bike. The rubberised grip is super sticky and tactile to touch. Fits easily on the 22mm handlebars for the rebuild. There is a ton of flexibilty but even with that, it fits spot on. Super happy with this product. Thank you Webike. Absolutely love them. View detail
Fits: KAWASAKI Z1000 R EDITION, KAWASAKI Z1000 R EDITION, KAWASAKI Z1000 R EDITION, KAWASAKI Z1000 R EDITION, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI NINJA ZX-6R
Genuine Kawasaki Clutch Lever for NINJA ZX-6R 2019
Webike have a lot of help tools available so you can find the correct part pretty easily to add an OEM Kawasaki Clutch Lever to the NINJA ZX-6R. Correct part number found and added to my basket. I generally have more itme in my basket ready to order and this was another that was added. I do like to order more than one part at a time as this cuts down the shipping if I was to order items individually. The courier I chose was EMS fast service. They do what they say and get your order to you very fast. No really sure if I have ever had an order delivered by this service that has been any longer than 5 days. This arrived at my door in 5 days as expected. This makes me happy and also my customers and friends happy too. The order was all packed really well as always from Webike warehouse staff. The outer box was sealed with tape so nothing could be lost whiclst in transit. The inner of the box was all neatly packed and filled with additional bubble wrap. Everything was nice and snug but not too tight to damage anything. All the parts and even some of the small parts arrived with me in 100% perfect condition. The lever is a lovely colur black, but not glossy balck, more like a satin. The finishing is perfect, no sharp parts and all the the groove where the cable sits in is also very well machined out. The clutch fitment tab is noce and smoothly finished. Even the bolt hole is very well machined. What's not to love. All fitted in super quick time and this meant my friend could get back out on his bike in just a week from the accident. Very happy with purchase. Thank you Webike for the great services you provide as always. View detail
Fits: KAWASAKI Z1000 R EDITION, KAWASAKI Z1000 R EDITION, KAWASAKI Z1000 R EDITION, KAWASAKI Z1000 R EDITION, KAWASAKI Z1000 ABS, KAWASAKI Z1000 ABS, KAWASAKI Z1000 ABS, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI Z1000
To 250SL High Solo
Diversion of ninja250SL to convert to High Solo.
The ends need to be cut because of its long length, otherwise it can be pontooned.
Quantity:Pair (for Left and Right) Since the Grip will change with the new Grip, I thought it would be a good idea to buy another Grip and replace it while you are at it.
The amount of change is slight, even for High Solo.
I will post a picture of the opening after the replacement. (I forgot to take a pic before the replacement)
View detail
Fits: KAWASAKI Z1000 ABS, KAWASAKI Z1000 ABS, KAWASAKI Z1000 ABS, KAWASAKI Z1000, KAWASAKI Z1000, KAWASAKI NINJA ZX-6RR, KAWASAKI Z1000, KAWASAKI NINJA ZX-6RR, KAWASAKI NINJA ZX-6R ABS, KAWASAKI NINJA ZX-6R ABS, KAWASAKI NINJA ZX-6R ABS, KAWASAKI NINJA ZX-6R ABS, KAWASAKI NINJA ZX-6R ABS, KAWASAKI NINJA ZX-6R ABS, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA ZX-6R
Clutch lever is definitely OEM.
I had been using Active's 3Finger RedLever, but since I have large hands, the bend of my elbow becomes unnatural, so I replaced it with the OEM.
And it's cheap.
View detail
Fits: KAWASAKI ZRX1200R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200R, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG
Calm Design.
The bar end is heavy and the handlebar's anti-vibration effect is the best weight because it is OEM. black, calm and simple design. the Locktite influence will damage the bolt if the correct tool is not used for the replacement. View detail
Fits: KAWASAKI ZZR1200, KAWASAKI ZZR1200, KAWASAKI ZZR1200, KAWASAKI ZZR1200, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX-II
The quality is unmistakable.
OEM parts are the best choice for you, and you can be sure of the high quality and reliability. The simple design of the switch housing gives it a relaxed atmosphere. View detail
Fits: KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG, KAWASAKI ZRX1200 DAEG
OEM is the best
I had scratched the mirror and was not sure whether I should replace it with one from Another Brand Product or not, but I chose the OEM one, which has a less-than-perfect design, but the installation accuracy and visibility are unmistakable. View detail
Fits: KAWASAKI ER-6F, KAWASAKI ER-6F, KAWASAKI ER-6F, KAWASAKI ER-4N ABS, KAWASAKI ER-4N ABS, KAWASAKI ER-4N, KAWASAKI 1400GTR, KAWASAKI ER-4N, KAWASAKI 1400GTR, KAWASAKI ER-6N, KAWASAKI ER-6F, KAWASAKI ER-6N, KAWASAKI ER-6N, KAWASAKI ER-6N, KAWASAKI ER-6N, KAWASAKI NINJA 250R, KAWASAKI NINJA 250R, KAWASAKI NINJA 250R, KAWASAKI NINJA 250R, KAWASAKI ER-6N
Operability is stable.
The Normal grip is the most stable and good quality, although it is not as flashy or custom as the Other Brand Product. The thickness, softness, grip comfort, and design are well thought out and produced only by OEMs. View detail