Reviews
MOTO LED for Fog LampSwitch HarnessKit
The configuration of the product is large and good, but the crimp on the wiring terminal of the Relay and Fuse part is not good enough, and it came off during the wiring. I would like you to use a solder or something to prevent the wiring from coming loose. View detail
Valve replacement
I replaced the Light on my SRX6 because it was dark. The brightness is now what I expected. View detail
It looks modern, but it's useless as a front light.
Installed and used on a V100. The quality and installation were perfectly fine, but the illumination range was too narrow to be useful as a front light. I regret that I jumped at it because it was cheap.
If you only run slowly with a 50cc, it may still be OK, but if you have to run at a reasonable speed in the suburbs at night, it's extremely dangerous. Even if a person comes out from a side road, you can't see him with this.
View detail
as one would expect
(I have already changed Relay, so I can't verify)
It's sturdy and seems to be of higher quality than the Chinese products on amazon etc.
Because it is G18 and small, it is not as bright as the explosion light, but the visibility has risen from the original Halogen, and the place where it is not annoying brightness at night is
By the way, another product of S25Size with the same mouth Gold and a lot of choices is very bright, but I think the original is G18Size, the depth is too narrow to fit
The appearance when not lit is also Refreshing because the Amber color has completely disappeared from Clear Lens.
I'm satisfied with the performance, but the price is too high.
For about 2,000 yen, I'd agree 5 stars.
View detail
The Switch width is narrow and easy to install, but the quality of the Harness itself is a bit unsatisfactory
[How is it used?
Purchased for the installation of the company's Fog light and Moto LED.
Was the one you received as per Image?
It consists of Harness, Relay, Switch, and Bullet Type Terminal, as per Image.
How was your experience with it?
Since there are Sea Rings and Cable exteriors in the necessary places beforehand, it can be pimped out if you are not particular.
[Points to note]
There are three things that bothered me. I'm sure they are fine for use with the company's LEDs.
1. The input and control wires of the Relay are on the same wire, and the car Both Sides +− and fog +− 2 sets of 6 wires are on the Wiring end.
In the Instruction Manual, the car Both Sides + line is directly linked to the battery or Accessories, but the former does not link to the main key and the latter does not link to the battery.
With the latter, I didn't think Relay made much sense because of the load on the ACC power supply.
(I modified the Relay control line to connect to ACC)
2. Since the core wire of Wiring is about 0.2sq, please be careful to connect Lamp with high load.
3. The Bullet Type Terminal for the fog is crimped with Male and Female terminals on the + and +minus; sides.
+There is a risk of shorting between Body ground when the wire is disconnected. (I have replaced it.)
How did it compare to other products?
We saw very few fog harnesses for motorcycles from other companies, and the ones we did see were almost double the price of this product.
From the price, I thought that the above-mentioned notes might be acceptable, but please be careful when you divert it.
View detail
That's about it.
The brightness is acceptable. Some kind of Bracket is necessary for installation, and whether the Wiring is on by a key or by another Switch depends on the Skill of the person who installs it. In the picture, Hexagonal Wrench is Quantity:It's a 2pc picture, but there's one in there, and it's loose enough to lick, too.
Both Bolt and Nut, which are supposed to be 10mm, are pleasantly loose. I'm not sure how durable they are yet, but hopefully they will last.
View detail
important point
important point
I checked the LIVEDio ZX-2002 in the compatibility chart and it was circle in PH11, so I bought it.
However, his own Valve is the First Model Type before ZX regulation, and the Valve shape called PH8X
Early pre-regulation ph8x
Pre- and post-regulation period - Post-regulation ph11
I should have opened it and looked at it before I bought it.
but the Head part is completely different between `96 and `97
But it is not listed in the Manufacturer's conformity chart.
Still, I could check the lights, so I ran the Engine and checked the lights, but
High flasher happened when I put Blinker on.
As the previous poster wrote, the high and low Wiring is reversed, so if you use the Bullet Terminal connection
Red Wiring on LED side should be attached to Blue (High) on Valve side Connector, Green is Black.
Fortunately, there is a car model after the regulation, and Valve of it is PH11, so I transplanted the head.
It has a blinker relay to prevent high flasher, so I'm going to put it on and see.
View detail
Good stuff
[How is it used? It is an alternative to Halogen bulb.
Was the one you received as per Image? Yes.
Was the installation difficult? It was not particularly difficult.
How was your experience with it? Brighter than Halogen bulb.
[Included Parts:were they on? None
[Was there anything that disappointed you? None
Other items that would be helpful
Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer It is not known whether it corresponds to the vehicle inspection.
View detail
It's just so bright!
Fits to Vespa Sprinit125
The OEM was Halogen, so by changing to LED, I am satisfied with the high quality and Large.
There is no special spec. and no fan attached, so it can be installed anywhere.
Now that it's in use, we just have to wait and see how long it lasts!
View detail
gutter
There is a rattle in the seat Gold of Valve, and it rattles even if it attaches to Light. So I replaced Valve's O-Ring with 1SizeLarge one and use it. View detail
It's more than twice as bright as Halogen, very nice!
Because Halogen bulbs cost from 2,000 to 4,000 yen, this one caught my eye for 6,000 yen when I was looking for an LED, and I bought and installed it.
It's bright enough, but I personally prefer 5000K instead of 6000K for the color, but you can't get that with LEDs!
As for one point of dissatisfaction, it installed in AF35 of DIO, but because the switch of HiLo became opposite, the terminal of Red and Yellow color of 3PinConnector of the LED side was pulled out using Precision Driver, it replaced and corresponded.
It would be great if the lifespan lasted more than 3 to 5 years, though!
View detail
It's so bright!
The headlight of Grom was too dark, so I changed to this LED.
Very bright and very happy.
And maybe the load on the Battery has been reduced, and the Grip heater has warmed up better.
It was a nice byproduct.
View detail
Bright!
The Fog Lamp is just so cool to have on!
You're going to the forest road! It's good when it conveys the vibe of "I'm not a fan of this"
In addition, it is possible to turn on/off the thing called this Fog Lamp with Toggle switch And that's even cooler when it comes to!
Switch&Fog Lamp will make your friends proud
No one else can understand "Switch With the
'Huh? What's this Switch? And I want to touch it, but I'm proud to see my friend who doesn't This is.. Try to explain that
I'm glad I put it on
View detail
Cosmo!
I don't know where it's made, but the quality is good considering the price!
I wasn't sure if I should use the Fog Lamp from PIAA, but this one is totally sufficient
It's rather brighter than Headlight, even from friends! I was told
It's that bright
It's good because it's an LED, which means less electricity is needed to power the product
View detail
Beware of mounting bolts!
Comparing with the LED fog of KITACO, I think that there is no large difference in shape and performance, and I think that there is a little bit less expensive LED fog I bought this Lamp
However, when trying to tighten the Bracket mounting bolts during installation, the M10 Can't slip and tighten with Spanner or Glasses, and the M9 tool won't fit?
When measured with Caliper, it was a whopping 9.5mm square Bolt and Nut
I don't have a tool of that size, so I ended up with an M10 Stainless bolt and Nut I bought the
In addition, the part of the body uses the Cap bolt of M3 I was about to lick it with Bolt, so I replaced it too
In the end, it might have been less expensive to buy a KITACO Lamp
I have no complaints about the key Lamp performance
View detail
It's brighter than I expected
I bought it for the auxiliary light on my XR250BAJA It is quite bright It is easy to install and I like it because it has a 1 year warranty It looks just like KITACO's, but KITACO doesn't seem to have a warranty, so I bought this one Purchase. wiring was taken with branching out from Light or when it switched to High beam more and more
It will be brighter It may be better to attach the Relay switch (sold separately) to make it more stable
So far, it's on without breaking, so we'll see how it goes Because it is not an expensive thing, if it breaks, I am going to replace Relay switch of a separate sale at the same time
View detail