Reviews
Fits: HONDA , SUZUKI , DUCATI , KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA1000, KAWASAKI Z1000, KAWASAKI Z800, TRIUMPH DAYTONA675, BMW S1000RR, BMW S1000RR
Good quality
Accuracy quality is good.
I should have checked the outside diameter dimensions of where the Hook hangs before purchasing.
It would be appreciated if you could indicate the size in the Catalogue Spec.
The diameter of the Attachment of the Rear stand is Small, Quantity:Set was not possible.
View detail
Fits: KAWASAKI NINJA ZX-10R, KAWASAKI NINJA ZX-6R, KAWASAKI NINJA1000, KAWASAKI Z1000, HONDA , SUZUKI , DUCATI , KAWASAKI Z800, BMW S1000RR, TRIUMPH DAYTONA675
Quality is satisfactory
The quality is satisfactory, but it is a little thicker than the STAND of DAYTONA and did not go all the way to the back of the Hook. View detail
improve labor efficiency (labour)
Maintenance is easier.
Some Screws need to be stopped with Screw locketc.
View detail
Looks good, strength might be a bit of a concern.
Normally, Axle Slider is attached with a penetrating Axle Shaft, but this Axle Slider has no Axle Shaft, and one side is installed with Included Parts:(like Universal Bar End) and the other side is installed with Axle It is a form of co-tightening with the Nut in it.
The shape is very good and it's pretty good for DressParts.
Installation is easy
The tools used are Hexagonal wrench and Torque wrench (for 100 N.m.)
Because I have never rolled, I do not know the performance at present, but I do not think that Axle does not shave Large.
However, the Right Side (Nut co-tightening side) has a thin body for the convenience of putting the Nut in, and when strong loads are applied, there is a possibility that it will be crushed.
However, when the Axle has fallen to the extent that this place is scraped, I think the time that Axle touches the ground is short, so I think it is Large sturdy as long as Nut is protected.
View detail
Satisfied (Lol)
For this price, you can't complain about this accuracy, build and quality!
At first I had to look around quite a bit to find this product But I'm glad I didn't buy expensive products from other companies (Lol)
Cost performance by quality/price is very high!
View detail
Try to install it
I installed it in TMAX 530 DX in 2007. The ground area became Large, and the sense of stability increased in places such as earth.
In the wearing picture, it was from the front, but there was no picture from the rear side, but I could not understand, but the tip of the presser foot floats a little.
I think that it is better to use glue on the Screw fastening part. Also, sometimes it is necessary to confirm that it is not loose.
View detail
Sitting sensation Imaichi
I changed from S1000XR to S1000R. I used Dimotiv when I was in front..
I could stop by just Screw and I was worried about falling. Because this item will attach Cover
I thought it looks relieved and purchased. Black Cover is slightly floating and the feeling of sitting is not good.
Reliability when stopping to loose ground, neither item is no problem.
I think that it is a problem of the BMW side.
View detail
Almost satisfied
Although Stand Hook comes out from various Manufacturers, the thing which is easy to get at the shop was scraped from the solid wood of Large Resistance Aluminum and it went on to Color Anodized Aluminum, so I was looking for somewhat elaborate design.
As a precaution, the Reverse side is hard to understand if it is a picture, but there is a cylindrical projection on the bottom side of the HookBody.
The body with the Hook attachment part on the lower side of the Swingarm is designed to adjust the step difference with Swingarm in that part, but in the case of the body with the Screw hole directly in Swingarm it will be quite unnatural shape.
Because I was here, I disconnected it with HandyGrinder and used it.
View detail