Reviews
It wasn't easy.
I bought it because I needed to change the handlebar.
I used WeBig because I was certain that no local Motorcycle parts store would be able to sell the parts I needed.
I think it is unnecessary for those who can do the processing themselves, but for amateurs, it was a very helpful part.
View detail
It is EXACTLY on Blinker's Grounding Wire!
[How is it used?
I needed to add a Grounding Wire when replacing the Blinker on my CB1100.
Was the one you received as per Image?
It was generally as per the Image, but Wiring was quite long.
Was the installation difficult?
The wiring is too long, but it might be better to cut it short if necessary.
How was your experience with it?
I have used them on all my Blinkers and have been able to light them without any glitches or problems at all.
[Included Parts:were they on?
Nothing else, including Instruction Manualetc.
[Was there anything that disappointed you?
Not at all. The inner diameter of the ring is 10mm, which is just the right size for CB1100, and the outer diameter is small, so it is not noticeable.
▼Quantity:1 Set of 2pcs. so if there are 4 Blinkers, Quantity:2 Sets are required.
Also, if the blinker body is made of gold, a grounding wire is required, but if the material is gold, a grounding wire is required.:In the case of a plastic blinker, this product is not necessary because the grounding wire is wired from the blinker.
View detail
Fits: KAWASAKI Estrella Custom, KAWASAKI VULCAN900Custom, KAWASAKI VULCAN900Custom, KAWASAKI NINJA2 Helmet50RR, KAWASAKI NINJA250R, KAWASAKI ESTRELLARSCustom, KAWASAKI ESTRELLARS, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI W800, KAWASAKI Z250 (2013-), KAWASAKI W650, KAWASAKI 250TR
nice kit
Cables and connectors are fine. Work excelent. Clamps are included, so it's easy to install. These cables are for swapping handlebar from low to very high, so if you'd like to install classic medium size there will be the wire surpluse. View detail
No need to process OEM Wiring and less expensive
ZX10R (2017) Rear Window Blinker to Other Brand Product Used to replace it
The same type of products are available from other companies, but the length of the wire and This is the only one that clearly states the size of this product, so I selected it
φ4mmBullet Type Terminal is automatic for This is the most common size used for VehicleAfterMarket parts
I even had the terminals in stock at my house from the beginning
(However, if the axis of the external Blinker is an M8 hollow bolt, the mounting nut is Wiring It is very difficult to put through the
Rumor has it that Deatna's product uses a 1-sized thin Bullet Type Terminal It seems to be there, so I think it's better for you
View detail
Fits: KAWASAKI Estrella Custom, KAWASAKI VULCAN900Custom, KAWASAKI VULCAN900Custom, KAWASAKI NINJA2 Helmet50RR, KAWASAKI NINJA250R, KAWASAKI ESTRELLARSCustom, KAWASAKI ESTRELLARS, KAWASAKI ESTRELLA, KAWASAKI ESTRELLA, KAWASAKI W800, KAWASAKI Z250 (2013-), KAWASAKI W650, KAWASAKI 250TR
Somewhat satisfied
Buy at the same time to exchange Handlebar for classicI 60.
Even an amateur can change easily, but the number of Harness has increased
A little ingenuity is needed when reinstalling Light after extending it or extending it.
If you have knowledge you may remove Harness and connect chords directly.
View detail
HURRICANEHURRICANE H4 Coupler Extension Harness
Used in CBR 250 RR.
Headlight attached to purchased Cowl was H4 Bulb, so it was good to convert with Adapter, but Wiring on the car body side did not reach the light case.
Since this product was almost JUST Length at 30 cm, it is used between H4 R → H 4 conversion adapter and H 4 Headlight Bulb.
I used about 8 months from installation, but I can use it without particular problems. I think that it is a good product.
View detail
During Blinker replacement
Just plug the Wiring on the side of the Blinker side with the Coupler on the car body side, you can exchange the Blinker immediately.
It is wonderful that you do not need to process any Wiring.
Without this, it would be troublesome to turn off the carbody side coupler and attach a bullet terminal.
View detail
A crack is not given to wiring by making it bite between a pure Coupler and a Blinker at the time of Blinker exchange currently used for Ninja250R,Moreover, since plug processing also of the wiring by the side of Blinker which can be ret
A crack is not given to wiring by making it bite between a pure Coupler and a Blinker at the time of
Blinker exchange currently used for Ninja250R,Moreover, since plug processing also of the wiring by the side of
Blinker which can be returned easily is carried out also when returning, if plug processing of the Blinker side is carried out, the Set of the Coupler is also sold by the DAYTONA etc. which can be attached [ that it is unprocessed and ], but.Since a price does not change so much, either, we recommend you here.
View detail