Reviews
Screwfor Hole
I didn't check it carefully, but it seems to be an M8 Screwfor Hole, not a product for filling a hole of M8Size. So the body is around M6 size.
It does not appear to fill the M8Size hole.
View detail
It would be nice to have a Type without Luster.
[How is it used?
TZr250R (3XV) I was concerned about the bare cap bolt on the Stem of the "Stem" so I bought it to put a lid on it.
I thought about using KITACOConvenienceParts, but I chose HURRICANE because it is a PRO around the handlebar and there were more of them.
Was the one you received as per Image?
1Quantity firmly as shown in the picture:It was 1 Set of 2pcs.
Was the installation difficult?
It can be installed in about 3 seconds as it just fits into the Bolt's head.
How was your experience with it?
As you can see in the photo, it is quite shiny, so it stands out a bit. (Lol)
Well, it can't be helped that it is probably intended for use in the bar Handlebar Post.
I'll try to get rid of the luster by easing it off a bit when I have time.
[Included Parts:were they on?
Cap only.
The bags are of a type that cannot be sealed, so it would be nice to have a Zip lock, etc. for storage.
[Was there anything that disappointed you?
Not really!
【Review】
It prevents Bolt from rusting and dirt from accumulating.
It is good for those who use it in such areas because of its gloss.
Also, since there are quite a few caps in the box, I will use them for cap bolt in places I am interested in.
View detail
For M8 is a little different?
First of all, please note that this is not a product for attaching to the hex holes of the Cap bolt. Do not blame the Manufacturer if you misunderstand the usage of this product.
I thought about what to do with the Screw holes that I had left partially visible and neglected, and remembered that there was also For M6 in the product I had bought to plug the M8 holes.
If you pick it up and compare the two, you will see that the texture of the head is different for some reason (minor change?), but the basic structure is the same. However, when you try to use them, the feel is slightly different.
The M8 for M8 is small and fits into the hole very well, whereas the M8 for M8 is not so responsive. The M8 for M8 has a head that fits tightly against the Exactly and fills the hole without gaps, making it difficult to remove, while the M8 for M8 has a slight rattle and can be removed by inserting a nail and pulling hard. I wonder if it is due to the difference in Screw Pitch.
View detail
Tiny but unobtrusive.
The M10 Screw mounting hole for the Stand Hook on the Swing Arm of the ZrX1200 DAEG is not used in the future, so I installed this Hole Plug. Is it really for M10Screw because it is unexpectedly small? I thought it would work, but it fit perfectly (laughs).
Pushing and rocking so you won't get blown away. Black resin, unobtrusive and Good.
View detail
Dress-up made easy
I bought this as a Cap for Fixing MirrorBolt.
I'm glad I put it on because every time it rains, the hexagonal hole part used to be a puddle of water.
Installation is also super easy, just lightly hammer in with a plastic hammer etc.
View detail
Ideal for covering up holes, but difficult to remove.
It is used for the screw hole of Plate which is exposed with footpeg position change. Because this is much cheaper than hiding with an ordinary Bolt, and the appearance seems to be good, I tried it.
The diameter of the head is almost the same as the screw hole and it is very neat. The protrusion on the side goes in easily in the inserting direction, and there is no need to worry about it coming off due to vibration as it is designed to catch on the screw thread in the pulling direction.
After that, the footpeg was finally installed in the same position as the original and this Cap was no longer needed, so I tried to remove it, but this time I had a problem. However, the Slotted screwdriver was not able to be put in at all because of the Smallness of the head diameter and the adhesiveness.
Fortunately, the hole I used is penetrating, so I was able to push it in with a driver and pull it out from the back. If the hole is non-Penetrating, you will need to drill a hole with a drill bit and cut it out with a cutter, etc.
Before you use it, you should really think about whether it's strong enough to cover it up and Large before you use it.
View detail
Damn it!
I bought it for the Mirror Hole Cover and it is much smaller than I thought it would be
When I first saw it, I thought it was either the diameter of the hole or the Bolt cap, but it's smaller than the Image is
It went in the screw hole of the M10 tightly, but the spit? I have no complaints if the outer diameter of the
It's returned, so it doesn't look like it was left out at all
View detail
Unnecessary Screw filling up
I removed the Left Side Mirror for commuting Scooter as it gets in the way because it slips through the traffic jam, but I tried using it for filling in the remaining M8Screw hole. It has a burr and is plugged into the Screw mountain when inserting it so that it can not be taken easily. I think that it is very convenient because it helps to protect Screw holes which are no longer used.
However, it is slightly troublesome as the head is Small when you remove it.
View detail
It purchased to the cover of the number anchor bolt. Although a silver deep pool is visible to the black of a goods photograph, thing is in the state of full black. It is thought that the number mounting part became full black and became tight.
It purchased to the cover of the number anchor bolt.
Although a silver deep pool is visible to the black of a goods photograph, thing is in the state of full black.
It is thought that the number mounting part became full black and became tight.
Black & plating is recommended.
View detail