Reviews
Price suitable
The screw holes were accurate and there are no problems with installation or appearance. View detail
good value for money
Material of Type using K-FACTORY's OEM License Lamp:I purchased this Eliminator to replace my Stainless Steel Fender Eliminator, which has a Stainless Steel base plate, black chrome plated and clear coated finish. I am satisfied with it because it is less expensive than other manufacturer's Fender Eliminator. In my case, I replaced the blinker with a POSH one, so it took time to adjust the angle and position of the blinker.
Of course, the accuracy was also fine. However, it would have been better if the bolts on the base plate were black instead of stainless steel.
View detail
It is a little regrettable.
Installation is easy due to the precision of the product.
However, the cord of the License lamp is halfway long and the attached Extension Cord is connected in a place where it is likely to be flooded.
I extended it with a solder and insulated it with a Shrinkable Tube.
The Others is a product I have no complaints about.
View detail
I would have been fine with OEMFender...
When I went through the OEM Fender to get a belt to fix the Seat bag, I found that the OEM Fender was plastic (not weak, but it would flex), so I decided to use the Fender Eliminator Kit, which was also inexpensive.
Probably the most difficult part of the installation is the removal of the OEMFender.
Instruction Manual does not have instructions for removing OEMFender.
However, if you are a do-it-yourselfer, you can remove the Rear Fender when you insert the ETCCard, so you may not have to do so much work (^^;)
The construction itself is solid, so the seat bag can be securely fastened to the belt.
I feel like it could be a little more behind the License Plate, but I am satisfied with the strength of the product.
View detail
On the GSR750
I chose this product because I like the clean Rear view. I like that it is not cluttered, but it may feel cheap to some people.
The process was easy and uneventful.
The LED Lamp is also beautiful, but the projection to attach the Lamp is a little too large.
If we drive long distances in the rain or on roads with floating dirt, our rear bags and backs will get dirty, but this is unavoidable.
The price is low and it is a good product!
View detail
Fits: HONDA CB400SF, HONDA CB400SF, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR, HONDA CB400SUPER BOLDOR
Refreshing with Slim design
I bought it because I wanted it to look Refreshing and Sexy from the back.
I am quite satisfied with the design, which is slimmer than other products.
I think most of the other companies' products are a little more blobby.
With this product, it seems as if it is integrated with Cowl.
The Instruction Manual was easy to understand and the DIY installation was a breeze.
View detail
Fits: KAWASAKI ER-6n, KAWASAKI NINJA400 (2014-), KAWASAKI Ninja 650
Fender Eliminator Kit
It arrived earlier than I expected, which was a big help. The instruction manual for installation is difficult to read … I thought it would be better to make it a little larger. I am very happy with the quality of the product and the price. View detail
HURRICANEFender Eliminator Kit
Wiring is also good because the Cover in the OEM Fender can be used as it is, so Wiring can be hidden. View detail
It was cool!
So much so that I can only ride on sunny days.
Mud splatter will be worse, but w
Installation is also easy after reading the instructions.
View detail
Looks better than stock
Does the job on my JB03 Monkey125. Lighter, more compact and better looking than stock Honda one. There are better looking ones available now, but this model was the cheapest at the time I bought it. View detail
High quality
The fitting was good, and the HarnessAdapter setting was smooth. The fitting was good and the HarnessAdapter was set up smoothly. View detail
Mounted on Gsx250r
Mostly satisfactory Level. Dry rating, a little bit of the part to be fixed to fit the body of the car is a little Quantity.:Pair (for Left and Right) There was a Gap. It is not visible unless you look through it, and there is no problem installing it. It is not too difficult to install. Included Parts:I think it is a satisfactory Level. View detail
Simple and good.
I wanted something with a crisp ParisRefreshing design as much as possible, so I chose this product.
However, as you can see, the rear tire is exposed, so my friend who was running behind me was not able to see the tire.
I never want to run behind you on a rainy day."
I was told.
View detail
Easy to install and good look
This eliminator kit is within a hour installed and contains all parts nieder. I had to readjust the angle of the Lizenzen plate due to german law. That is no problem with this product. Recommended. View detail
Fit as expected
I am satisfied with the Large change with the finish as I imagined.
The mud splatter must be great because the rear tire is fully exposed when viewed from behind, as shown in the photo.
I'm thinking of buying a slightly longer inner fender to deal with this.
The only slight disappointment was that the wiring of the license lamp was reversed in the Instruction Manual.
I also need to buy more Number base with Reflector.
View detail
Fits: KAWASAKI ZX-14R, KAWASAKI ZZR1400 (ZX-14)
Simple and good angles
Simple and easy to install. The angle is nice, but it can be bent in a vise for freedom.
I hope the price is a little lower since it is Simple.
View detail
Simple and sleek rear
If you install a fenderless kit than a basic rear-fender, it turns into a much sleeker back. It is difficult to install the Korean number plate right away, so processing work is needed. View detail
Fits: YAMAHA Bolt CSpecifications, YAMAHA Bolt, YAMAHA Bolt
Compared to other companies.
I bought this one compared to the other company's product based on appearance alone, but I actually had to purchase the Reflector separately, which is a bit of a hassle.
However, the good thing about these parts is that, like the OEM, they cover the various wiring parts and completely hide them when viewed from the reverse side. This effect will not show up in a short period of time, but I think it is highly effective in protecting the wiring from waterproofing and damage caused by possible contact with the tires.
View detail
Also fits JC91
I didn't dislike OEMFender for a long time, but Custom lust inspired me to install it.
The length is not too short, not too long, and can be easily accessed by the key under the Tail Lamp.
Although it is compatible with JC79, it can be installed on JC91 without any modification.
The installation parts consist of three simple pieces. The installation is not as complicated as other companies' products, and is simple and clear. However, because it is made to be just the right size, you may feel for a moment that the size does not fit when installing it on the car body.:Pair (for Left and Right) If you fit it while spreading it out on the "Snap", it will fit comfortably with the Snap.
The long wiring that is difficult to deal with after assembly can be neatly accommodated by crawling along the RiderSeat side together with the harness on the Tandem seatLeft Side. The BlinkerCoupler, which is just exposed, can be protected with Sponge tape to prevent rattling noise.
This kit does not include a reflector, so a separate reflector kit is required. The Number base is thick enough to be used with a Reflector, but I don't think a separate License Frame is necessary. However, I use POSH's Horizontal Type Plate Holder which I used for OEM Fender, and I can install it without any problem.
Also, following the example of the Fender Eliminator, if you run in wet areas, you will get mud all over your back, so be careful of puddles and run on sunny days or you will need a Mud Guard.
Recommendation for installation if you want to highlight the trapezoidal ShortBody of the CB-RSeries.
I was debating whether to go with the Fender Eliminator until just before I bought it, but I thought I would just install it and remove it if I didn't like it, but I now like it very much.
View detail
Fender Eliminator in HURRICANE
[How is it used?
The size is perfect to the point where the cover of the Normal blinker fits.
Easy to install and work with
Was the one you received as per Image?
Street Image
Was the installation difficult?
Easy to do if you have a Driver and Ratchet tool.
How was your experience with it?
Satisfied with Refreshing and Sharp around Fender as intended.
The material is aluminum and painted, so it looks simple but is solidly made.
[Included Parts:were they on?
with Exclusive Harness・Led License Lamp
[Was there anything that disappointed you?
When the Led License Lamp is installed, it comes into contact with the Stop-lamp, which causes vibration.
Concerns about LampCover cracking.
Items/Reflector that should be purchased together must be purchased and installed
View detail