Reviews
usually
Installed on HURRICANE's Duralumin Pipe Handlebar.
It is a very ordinary Bar end cap, but I think it is a nice slit in it.
Rubbers for inner diameters from 14mm and 18mm are included.
View detail
Mounted on the company's Swallow handle
Since the bar end was replaced with the company's Swallow handle, the bar end was also selected from the company's compatible products with SliderType and Weight.
Installation is general, and is done by attaching it to the end of the Handlebar and tightening the Bolt at the Bar End.
I drove the car after installation and felt very little hand-shaking vibration.
However, since the swallow handle itself is made of steel and is sturdy, it seems that inner weight can be added depending on the handlebar to be installed and the type of car.
As for the Slider function, I haven't tipped it over yet, so it hasn't really worked, but if it does, the Handlebar won't get stuck and around the Stem? I was hoping that it would reduce the Damage of the Stem.
View detail
Good and understated!
I chose it for its understated design. The texture is not bad, but … Hmm? If you look closely, you can see that the Bar End and the Weight are in different colors! View detail
I have been able to use it without any glitches!
[How is it used?
Bar End is required because of the hole type Grip.
Was the one you received as per Image?
It was just like the image.
Was the installation difficult?
Easy to install.
How was your experience with it?
There are no particular problems and I am able to use it.
[Included Parts:were they on?
Quantity of Rubber and Screws:Set
[Was there anything that disappointed you?
Not particularly, but Material:It is Aluminum and is easily scratched.
View detail
It's a normal Bar End.
It's a normal Bar End.
It's weighted.
Of course, this does not seem to have much effect on 4-cylinder engines.
This will work for TWIN and SINGLE.
It's more functional than something that focuses on the eyes of a desga. (Weight) Emphasis.
I'm focusing on weight, so I can't help the appearance. (A little sloppy.)
This time, I installed it on the same HURRICANE Handlebar.
The others. When you tighten the bolt, there will be a gap between the grip and the bolt. If there is a gap between the two parts, you can use a plastic hammer to remove it.
Parts cleaner will vaporize eventually, so no problem. You can't do that with Raspene.
View detail
Vibration prevention
It is a SingleMotorcycle and I bought it to prevent vibration.
Well, it seems that the vibration is reduced.
View detail
Cheap and easy
I replaced the deteriorated Bar End with a simple design plastic Bar End, which is the closest in shape to the original one.
The feeling that I tapped it in was not so strongly pressed in, but it was not the Level that seemed to fall out, so I looked at it for the time being. There seems to be no problem in matching with the old Handlebar made in Italy.
View detail
The thing itself isn't bad.
I think the thing itself is not bad, but I'm afraid that the rubber inside is too short or it might slip out.
I Check it every time I ride it (laughs).
FUSION's Normal grip is not penetrating and originally does not have a grip end, but I bought it to cover the hole because I installed a grip heater.
View detail
Made by HURRICANEHandlebar
I am using it with "Made by HURRICANEHandlebar" by Grom Since the brands are the same, fitting is not too tight and not too loose
As may be the case with this type of bar end in general, once it is installed and removed The next time you install it, you need to apply a thin layer of glue to prevent it from falling off I am
If you have a few falls, there is no harm in having it because it also has a Slider effect
View detail
Fits: KAWASAKI Estrella Custom, KAWASAKI ZRX400II, KAWASAKI ZR-7/S, KAWASAKI ZRX400, SUZUKI GSX1400, YAMAHA YZF-R1, HONDA PCX125, HONDA CB1300 SF, HONDA CB750, HONDA VFR400R, HONDA SILVER WING400, HONDA SILVER WING600, HONDA FAZE, HONDA FAZE Type S, HONDA FORZA Z ABS, HONDA FORZA(MF06), HONDA FORZA(MF06), HONDA FORZA(MF08), YAMAHA FZ400, SUZUKI GSR750
It's easy to change the image!
CB750 (RC42) attached to the
It could easily be replaced with the OEM Bar End
The image also changes dramatically However, as my preference, I think that the cannonball type is still Large human-like
The texture is very good
But it's very light, so if you have a large single cylinder or TWIN of vibration, you may suffer from vibration Isn't it?
View detail
Cospar good
This is a simple plastic plug It's not cheap and not flashy, but better than nothing, if you don't care about it, I recommend this one You may need to cut the inside diameter of the Handlebar to fit it, but it's better than a loose plug I think rainwater can get into the Handlebar View detail
Unified with Red
Large seems to be insufficient and it is casually seeming to insist on existence. It is appreciated that various colors are prepared and there are many choices. View detail
Pretty good
Since what I used before was hit by it and it got hurt, I purchased it. I purchased it with expectation for UVCoat. The feeling that I installed was surprisingly good. After that Red is easy to color, so I expect how much UVCoat will work. View detail
usually.
Simultaneous purchase at the time of Handlebar exchange.
Easy to install but good texture etc etc. Because it is an ordinary commodity,
It may be unsuitable for those looking for luxury and Custom feeling in this Parts.
View detail
Attached on the inside of Separate handle to add electrical equipment.
I attached it inside the LeftSeparate handle of GSX-R1000.
I removed the end cap of Plastic, I measured the inner diameter and bought this Size. (Owner may change the Separate handle to Made by HURRICANE and the inner diameter may be different from NORMAL)
The way of attachment, by turning the hexagon at the tip, the opposite insertion side tip is pulled and Material : The Rubber barrel spreads out and makes you feel at ease inside the inner diameter of Separate handle. As Rubber is leaning in, it does not fit with Firmly. If you move it by hand, it moves slightly but it is not feeling like falling off while driving.
Length may be felt a bit short, but I think that it is OK even in this Length if we consider only one equipment to increase one.
Currently I am using it to add USB power supply.
View detail
The Side cap was also attached simultaneously with Handle exchange of a HURRICANE.appearance also has a high grade feeling and I think that structure is also solid! Neither engine performance nor appearance has dissatisfaction! Although there were
The Side cap was also attached simultaneously with Handle exchange of a HURRICANE.
appearance also has a high grade feeling and I think that structure is also solid! Neither
engine performance nor appearance has dissatisfaction! Although there were also
, however my shortage of knowledge, since a description did not have anything, either, the first attachment was puzzled.He has understood by a friend's advice.
I was that which is said and wanted the description.
View detail
Since both were missing, the Balancer of the Motorcycle purchased in medieval times purchased this product. Attachment is easy, structure is also solid and appearance is more good-looking than the Balancer of an original manufacturer's product. Although
Since both were missing, the Balancer of the Motorcycle purchased in medieval times purchased this product. Attachment is easy, structure is also solid and appearance is more good-looking than the Balancer of an original manufacturer's product. Although it is unnecessary addition, the hezagonal wrench in a goods photograph is not attached. Although an Image which is truly attached is made to hold ... Although it is trifles, I would like to come to suspect an intention of a Manufacturer. View detail
It is attachment at DR-Z400SM. Since the wire interfered just before in attaching a clutch etc. and the burden was placed also on the cable since motard vehicles [ origin ] when separate-handle-izing, it thought whether there would be any good hands a
It is attachment at DR-Z400SM.
Since the wire interfered just before in attaching a clutch etc. and the burden was placed also on the cable since motard vehicles [ origin ] when separate-handle-izing, it thought whether there would be any good hands and purchased.
Although 25-mm mere extension may be thought, it was very saved.
Even if it attaches a grip and a throttle, there is not that the extended grip part turns etc.
the direction in which the same trouble is held is tried -- valuable -- it is -- !!.
View detail
It is the best for attaching navigation.
It is the best for attaching navigation. View detail
Fits: KAWASAKI Estrella Custom, KAWASAKI ZRX400II, KAWASAKI ZRX400, KAWASAKI ZR-7/S, HONDA PCX125, SUZUKI GSX1400, YAMAHA YZF-R1, HONDA CB1300 SF, HONDA CB750, HONDA VFR400R, HONDA SILVER WING400, HONDA SILVER WING600, HONDA FAZE, HONDA FAZE Type S, HONDA FORZA Z ABS, HONDA FORZA(MF06), HONDA FORZA(MF06), HONDA FORZA(MF08), YAMAHA FZ400, SUZUKI GSR750
Although there are few aftermarket parts of a street triple and they are expensive, this is bolt-on OK! Since plating treatment has many motorcycles itself, harmony of the circumference of a handle is further good. An attached screw is also easily
Although there are few aftermarket parts of a street triple and they are expensive, this is bolt-on OK!
Since plating treatment has many motorcycles itself, harmony of the circumference of a handle is further good.
An attached screw is also easily exchangeable for the nut in Bar with one settlement driver easily.
View detail