Reviews
Installation Comments
Easy to install, but will loosen as it is not a Nut lock. View detail
Mounted on a replaced external Handlebar (SWCondor)
After replacing the handlebar, I noticed a slight continuous vibration that had not been there before, and I realized the importance of the weight that is inserted in the OEM bar. The problem was that the ZETA hand guard installed on the bar end had an M8 bolt. As a result, we prepared a 10mm longer bolt and used an M8→M6 conversion joint.
When we ran the actual run, the vibration disappeared, and the effect was outstanding.
View detail
I don't like the Round Type Mirror on the 2024GROM.
I purchased this product because I could not get used to the design of GROM's Round Type Mirror, which was apparently a reuse of the for MONKEY mirror.
I chose "Made by HURRICANE" because I thought it was better than the inferior "Large Land" products. The installation is not so difficult, but there is no instruction manual, and the package is not printed, so inexperienced users may have some trouble!
The design is good, but the Mirror angle has a small vertical adjustment range and requires fine adjustment at the Lever mounting point.
Somewhat disappointing in terms of product
View detail
Excellent product, very, very well made. Installing is not an easy job, but that's due to W800 mechanics
This is an excellent product. I am installing a plush comfort seat which is slightly higher, and with these bars the geometry is perfect for touring. Quality is top notch. Everything is very well made, everything fits and well thought through. I would not try to install it unless you are capable enough to build the bike ground up. On mine, tank and light had to come off on top of obvious cables, break lines, etc. 4 hour job easily. If you are anything less than a master, give it to your trusted mechanic and pay accordingly. In case of W800, it is just how the bike is laid out, not a a fault of this product. In fact, because of everything fits so well, Hurricane have made it as easy as at all possible for this Kawasaki. View detail
Inexpensive and practical
Inexpensive and practical.
Necessary and sufficient
View detail
Inexpensive and practical
Inexpensive and practical.
Necessary and sufficient
View detail
Inexpensive and practical
Inexpensive and practical.
Necessary and sufficient
View detail
Conti II type can be NORMAL.
The OEMHandlebar is so large that if it is replaced with a narrower one, the OEM will have a little extra space.
However, it could be left as OEM, but it interfered with the RadiatorRight Side surface.
It is a product that is better to have than not to have.
View detail
Fits: HONDA CB1100, HONDA CB1300SUPER BOLDOR, HONDA FTR223, HONDA NC700X, HONDA MONKEY, KAWASAKI 250TR, KAWASAKI W400, SUZUKI RV200 VANVAN, SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER Big Boy, SUZUKI GRASS TRACKER Big Boy, YAMAHA TW200, YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW225E
Type 2 to Type 3
I was using a Police Type 2 and changed to a Type 3 to get a little more up.
The length of the wire was delicate and I had prepared a long wire, but it was better to use a narrower wire, so I was able to use an OEM wire.
I prepared another one and narrowed the width further to my liking at 655mm.
View detail
Bar handle has
I used to use 10cm Long on my HURRICANE Pipe Handlebar Kit, but it was too long, so I decided to use 5cm.
Clearance is just fine.
View detail
What about shipping?
It's been over a year, have you shipped the product yet? View detail
Replace OEMHandlebar
Separate Handlebars are too aggressive; Swallow handle is too short
Therefore, it becomes Condor Handle.
However, in the reverse position (where the Grip is lower than the Clamp), there is too little Clearance between the bar and the Blinker.
View detail
HURRICANE HURRICANE Reflector
The product was as per the Image.
There will be a gap between the Number and the Reflector, so we do not recommend this if you are concerned about this. (It will look like it is gnawing out of the Number.)
View detail
HURRICANE HURRICANE Cat's Eye Mini Tail Lamp Kit
[How is it used?
The OEM tail lamp was replaced because it was too large.
Was the one you received as per Image?
It was nice and clean as per Image.
Was the installation difficult?
It is not that difficult.
How was your experience with it?
It was nice to see it look shapely.
It is good because I have not seen many people installing them.
[Included Parts:were they on?
There is none
[Was there anything that disappointed you?
The point where the Red light from the Tail lamp illuminates the Number.
Blackish Tape was pasted inside to keep it from illuminating.
View detail
Fits: HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, HONDA CB400SF, KAWASAKI W400, KAWASAKI 250TR, HONDA MONKEY, HONDA MONKEY, HONDA HORNET250, HONDA NC700S, HONDA FTR223, HONDA FTR223, HONDA CB750, HONDA CB400SUPER BOLDOR, YAMAHA TW225E, YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW200, YAMAHA SR500, YAMAHA SR400
Best Match for Good Position XSR125.
The handlebar on my XSR125 did not fit and my shoulder stiffness got worse after the first ride, so I replaced it with this handlebar based on Net information.
I also bought a Flat continental2 type and compared it with the BMConti3 type while temporarily attaching it, and found that the BMConti3 type fit better.
It's so easy to ride that I think this should be the standard now! It is so easy to ride. I recommend it.
I had prepared a riser, but I am 175cm tall and it is just right without the riser.
Small patterned person is Quantity:SetBackRiser would be a good position.
Drilling is required, but a drill driver is sufficient for this purpose as long as the position is marked temporarily and the punch is firmly applied.
It is hang to go little by little while checking, not trying to open it all at once.
It was a good buy for the XSR125.
View detail
Price suitable
The screw holes were accurate and there are no problems with installation or appearance. View detail
Fits: SUZUKI RV200 VANVAN, SUZUKI GRASS TRACKER, SUZUKI GRASS TRACKER Big Boy
meticulous manufacturing
It was good up to the point of installing the Coupler on the body side of the NORMALIndicator with the Coupler, but the remaining Black color code was installed with Tap for Connection and the Instruction Manual's Sky blue code. The sky-blue code is used to connect to the Quantity:There are 2 pcs and the first connection failed, but I opened the Tap and connected it to the dark sky blue cord and it lit up fine. View detail
(Commuting) BattleMirror
I was concerned about the width of OEMMirror and purchased it. It is not only wide, but also tall, and is built as expected.
Compared to other products, the design is more OEM-like, so I think the balance with the overall body is good.
By the way, this is the second time I bought this because the one I bought before broke.
View detail
Fits: HONDA HORNET250, HONDA APE 50, HONDA APE 50, HONDA APE 100, HONDA VTR250, HONDA VTR250, HONDA NC700S, HONDA FTR223, KAWASAKI ZRX1100II, KAWASAKI ZRX1100, KAWASAKI W800, KAWASAKI W400, KAWASAKI ZEPHYR400, YAMAHA XJR400R, YAMAHA XJR1300, YAMAHA XJR1300, YAMAHA TW225E, YAMAHA TW200E, YAMAHA TW200E, YAMAHA TW200
This is what it looks like when installed on a KTM 2013 DUKE.
This is what a BMConti2-type Handlebar looks like when attached to an Initial ModelDUKE. Finger is about the same height as Limit. View detail
Fits: YAMAHA XJR400R, YAMAHA XJR400, YAMAHA V-MAX 1200, YAMAHA SRV250, YAMAHA SR400, YAMAHA FZR400, SUZUKI GSF1200, KAWASAKI ZR-7/S, HONDA Monkey BAJA, SUZUKI GSF750, YAMAHA XJR400, YAMAHA XJR1300, YAMAHA XJR1200R, YAMAHA XJR1200, YAMAHA SRX600, YAMAHA SRX400, YAMAHA SRX400, YAMAHA FZR250R, YAMAHA FZ400, SUZUKI BANDIT400
HURRICANE triangular table spindle nut
Exquisite workmanship, cheap price, good materials, beautiful colors, very accurate size, easy to install, and fits perfectly in the car View detail